1#ifndef _IPATH_KERNEL_H
2#define _IPATH_KERNEL_H
3/*
4 * Copyright (c) 2006, 2007, 2008 QLogic Corporation. All rights reserved.
5 * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
6 *
7 * This software is available to you under a choice of one of two
8 * licenses.  You may choose to be licensed under the terms of the GNU
9 * General Public License (GPL) Version 2, available from the file
10 * COPYING in the main directory of this source tree, or the
11 * OpenIB.org BSD license below:
12 *
13 *     Redistribution and use in source and binary forms, with or
14 *     without modification, are permitted provided that the following
15 *     conditions are met:
16 *
17 *      - Redistributions of source code must retain the above
18 *        copyright notice, this list of conditions and the following
19 *        disclaimer.
20 *
21 *      - Redistributions in binary form must reproduce the above
22 *        copyright notice, this list of conditions and the following
23 *        disclaimer in the documentation and/or other materials
24 *        provided with the distribution.
25 *
26 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
27 * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
28 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
29 * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
30 * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
31 * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
32 * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
33 * SOFTWARE.
34 */
35
36/*
37 * This header file is the base header file for infinipath kernel code
38 * ipath_user.h serves a similar purpose for user code.
39 */
40
41#include <linux/interrupt.h>
42#include <linux/pci.h>
43#include <linux/dma-mapping.h>
44#include <linux/mutex.h>
45#include <linux/list.h>
46#include <linux/scatterlist.h>
47#include <asm/io.h>
48#include <rdma/ib_verbs.h>
49
50#include "ipath_common.h"
51#include "ipath_debug.h"
52#include "ipath_registers.h"
53
54/* only s/w major version of InfiniPath we can handle */
55#define IPATH_CHIP_VERS_MAJ 2U
56
57/* don't care about this except printing */
58#define IPATH_CHIP_VERS_MIN 0U
59
60/* temporary, maybe always */
61extern struct infinipath_stats ipath_stats;
62
63#define IPATH_CHIP_SWVERSION IPATH_CHIP_VERS_MAJ
64/*
65 * First-cut critierion for "device is active" is
66 * two thousand dwords combined Tx, Rx traffic per
67 * 5-second interval. SMA packets are 64 dwords,
68 * and occur "a few per second", presumably each way.
69 */
70#define IPATH_TRAFFIC_ACTIVE_THRESHOLD (2000)
71/*
72 * Struct used to indicate which errors are logged in each of the
73 * error-counters that are logged to EEPROM. A counter is incremented
74 * _once_ (saturating at 255) for each event with any bits set in
75 * the error or hwerror register masks below.
76 */
77#define IPATH_EEP_LOG_CNT (4)
78struct ipath_eep_log_mask {
79	u64 errs_to_log;
80	u64 hwerrs_to_log;
81};
82
83struct ipath_portdata {
84	void **port_rcvegrbuf;
85	dma_addr_t *port_rcvegrbuf_phys;
86	/* rcvhdrq base, needs mmap before useful */
87	void *port_rcvhdrq;
88	/* kernel virtual address where hdrqtail is updated */
89	void *port_rcvhdrtail_kvaddr;
90	/*
91	 * temp buffer for expected send setup, allocated at open, instead
92	 * of each setup call
93	 */
94	void *port_tid_pg_list;
95	/* when waiting for rcv or pioavail */
96	wait_queue_head_t port_wait;
97	/*
98	 * rcvegr bufs base, physical, must fit
99	 * in 44 bits so 32 bit programs mmap64 44 bit works)
100	 */
101	dma_addr_t port_rcvegr_phys;
102	/* mmap of hdrq, must fit in 44 bits */
103	dma_addr_t port_rcvhdrq_phys;
104	dma_addr_t port_rcvhdrqtailaddr_phys;
105	/*
106	 * number of opens (including slave subports) on this instance
107	 * (ignoring forks, dup, etc. for now)
108	 */
109	int port_cnt;
110	/*
111	 * how much space to leave at start of eager TID entries for
112	 * protocol use, on each TID
113	 */
114	/* instead of calculating it */
115	unsigned port_port;
116	/* non-zero if port is being shared. */
117	u16 port_subport_cnt;
118	/* non-zero if port is being shared. */
119	u16 port_subport_id;
120	/* number of pio bufs for this port (all procs, if shared) */
121	u32 port_piocnt;
122	/* first pio buffer for this port */
123	u32 port_pio_base;
124	/* chip offset of PIO buffers for this port */
125	u32 port_piobufs;
126	/* how many alloc_pages() chunks in port_rcvegrbuf_pages */
127	u32 port_rcvegrbuf_chunks;
128	/* how many egrbufs per chunk */
129	u32 port_rcvegrbufs_perchunk;
130	/* order for port_rcvegrbuf_pages */
131	size_t port_rcvegrbuf_size;
132	/* rcvhdrq size (for freeing) */
133	size_t port_rcvhdrq_size;
134	/* next expected TID to check when looking for free */
135	u32 port_tidcursor;
136	/* next expected TID to check */
137	unsigned long port_flag;
138	/* what happened */
139	unsigned long int_flag;
140	/* WAIT_RCV that timed out, no interrupt */
141	u32 port_rcvwait_to;
142	/* WAIT_PIO that timed out, no interrupt */
143	u32 port_piowait_to;
144	/* WAIT_RCV already happened, no wait */
145	u32 port_rcvnowait;
146	/* WAIT_PIO already happened, no wait */
147	u32 port_pionowait;
148	/* total number of rcvhdrqfull errors */
149	u32 port_hdrqfull;
150	/*
151	 * Used to suppress multiple instances of same
152	 * port staying stuck at same point.
153	 */
154	u32 port_lastrcvhdrqtail;
155	/* saved total number of rcvhdrqfull errors for poll edge trigger */
156	u32 port_hdrqfull_poll;
157	/* total number of polled urgent packets */
158	u32 port_urgent;
159	/* saved total number of polled urgent packets for poll edge trigger */
160	u32 port_urgent_poll;
161	/* pid of process using this port */
162	struct pid *port_pid;
163	struct pid *port_subpid[INFINIPATH_MAX_SUBPORT];
164	/* same size as task_struct .comm[] */
165	char port_comm[16];
166	/* pkeys set by this use of this port */
167	u16 port_pkeys[4];
168	/* so file ops can get at unit */
169	struct ipath_devdata *port_dd;
170	/* A page of memory for rcvhdrhead, rcvegrhead, rcvegrtail * N */
171	void *subport_uregbase;
172	/* An array of pages for the eager receive buffers * N */
173	void *subport_rcvegrbuf;
174	/* An array of pages for the eager header queue entries * N */
175	void *subport_rcvhdr_base;
176	/* The version of the library which opened this port */
177	u32 userversion;
178	/* Bitmask of active slaves */
179	u32 active_slaves;
180	/* Type of packets or conditions we want to poll for */
181	u16 poll_type;
182	/* port rcvhdrq head offset */
183	u32 port_head;
184	/* receive packet sequence counter */
185	u32 port_seq_cnt;
186};
187
188struct sk_buff;
189struct ipath_sge_state;
190struct ipath_verbs_txreq;
191
192/*
193 * control information for layered drivers
194 */
195struct _ipath_layer {
196	void *l_arg;
197};
198
199struct ipath_skbinfo {
200	struct sk_buff *skb;
201	dma_addr_t phys;
202};
203
204struct ipath_sdma_txreq {
205	int                 flags;
206	int                 sg_count;
207	union {
208		struct scatterlist *sg;
209		void *map_addr;
210	};
211	void              (*callback)(void *, int);
212	void               *callback_cookie;
213	int                 callback_status;
214	u16                 start_idx;  /* sdma private */
215	u16                 next_descq_idx;  /* sdma private */
216	struct list_head    list;       /* sdma private */
217};
218
219struct ipath_sdma_desc {
220	__le64 qw[2];
221};
222
223#define IPATH_SDMA_TXREQ_F_USELARGEBUF  0x1
224#define IPATH_SDMA_TXREQ_F_HEADTOHOST   0x2
225#define IPATH_SDMA_TXREQ_F_INTREQ       0x4
226#define IPATH_SDMA_TXREQ_F_FREEBUF      0x8
227#define IPATH_SDMA_TXREQ_F_FREEDESC     0x10
228#define IPATH_SDMA_TXREQ_F_VL15         0x20
229
230#define IPATH_SDMA_TXREQ_S_OK        0
231#define IPATH_SDMA_TXREQ_S_SENDERROR 1
232#define IPATH_SDMA_TXREQ_S_ABORTED   2
233#define IPATH_SDMA_TXREQ_S_SHUTDOWN  3
234
235#define IPATH_SDMA_STATUS_SCORE_BOARD_DRAIN_IN_PROG	(1ull << 63)
236#define IPATH_SDMA_STATUS_ABORT_IN_PROG			(1ull << 62)
237#define IPATH_SDMA_STATUS_INTERNAL_SDMA_ENABLE		(1ull << 61)
238#define IPATH_SDMA_STATUS_SCB_EMPTY			(1ull << 30)
239
240/* max dwords in small buffer packet */
241#define IPATH_SMALLBUF_DWORDS (dd->ipath_piosize2k >> 2)
242
243/*
244 * Possible IB config parameters for ipath_f_get/set_ib_cfg()
245 */
246#define IPATH_IB_CFG_LIDLMC 0 /* Get/set LID (LS16b) and Mask (MS16b) */
247#define IPATH_IB_CFG_HRTBT 1 /* Get/set Heartbeat off/enable/auto */
248#define IPATH_IB_HRTBT_ON 3 /* Heartbeat enabled, sent every 100msec */
249#define IPATH_IB_HRTBT_OFF 0 /* Heartbeat off */
250#define IPATH_IB_CFG_LWID_ENB 2 /* Get/set allowed Link-width */
251#define IPATH_IB_CFG_LWID 3 /* Get currently active Link-width */
252#define IPATH_IB_CFG_SPD_ENB 4 /* Get/set allowed Link speeds */
253#define IPATH_IB_CFG_SPD 5 /* Get current Link spd */
254#define IPATH_IB_CFG_RXPOL_ENB 6 /* Get/set Auto-RX-polarity enable */
255#define IPATH_IB_CFG_LREV_ENB 7 /* Get/set Auto-Lane-reversal enable */
256#define IPATH_IB_CFG_LINKLATENCY 8 /* Get Auto-Lane-reversal enable */
257
258
259struct ipath_devdata {
260	struct list_head ipath_list;
261
262	struct ipath_kregs const *ipath_kregs;
263	struct ipath_cregs const *ipath_cregs;
264
265	/* mem-mapped pointer to base of chip regs */
266	u64 __iomem *ipath_kregbase;
267	/* end of mem-mapped chip space; range checking */
268	u64 __iomem *ipath_kregend;
269	/* physical address of chip for io_remap, etc. */
270	unsigned long ipath_physaddr;
271	/* base of memory alloced for ipath_kregbase, for free */
272	u64 *ipath_kregalloc;
273	/* ipath_cfgports pointers */
274	struct ipath_portdata **ipath_pd;
275	/* sk_buffs used by port 0 eager receive queue */
276	struct ipath_skbinfo *ipath_port0_skbinfo;
277	/* kvirt address of 1st 2k pio buffer */
278	void __iomem *ipath_pio2kbase;
279	/* kvirt address of 1st 4k pio buffer */
280	void __iomem *ipath_pio4kbase;
281	/*
282	 * points to area where PIOavail registers will be DMA'ed.
283	 * Has to be on a page of it's own, because the page will be
284	 * mapped into user program space.  This copy is *ONLY* ever
285	 * written by DMA, not by the driver!  Need a copy per device
286	 * when we get to multiple devices
287	 */
288	volatile __le64 *ipath_pioavailregs_dma;
289	/* physical address where updates occur */
290	dma_addr_t ipath_pioavailregs_phys;
291	struct _ipath_layer ipath_layer;
292	/* setup intr */
293	int (*ipath_f_intrsetup)(struct ipath_devdata *);
294	/* fallback to alternate interrupt type if possible */
295	int (*ipath_f_intr_fallback)(struct ipath_devdata *);
296	/* setup on-chip bus config */
297	int (*ipath_f_bus)(struct ipath_devdata *, struct pci_dev *);
298	/* hard reset chip */
299	int (*ipath_f_reset)(struct ipath_devdata *);
300	int (*ipath_f_get_boardname)(struct ipath_devdata *, char *,
301				     size_t);
302	void (*ipath_f_init_hwerrors)(struct ipath_devdata *);
303	void (*ipath_f_handle_hwerrors)(struct ipath_devdata *, char *,
304					size_t);
305	void (*ipath_f_quiet_serdes)(struct ipath_devdata *);
306	int (*ipath_f_bringup_serdes)(struct ipath_devdata *);
307	int (*ipath_f_early_init)(struct ipath_devdata *);
308	void (*ipath_f_clear_tids)(struct ipath_devdata *, unsigned);
309	void (*ipath_f_put_tid)(struct ipath_devdata *, u64 __iomem*,
310				u32, unsigned long);
311	void (*ipath_f_tidtemplate)(struct ipath_devdata *);
312	void (*ipath_f_cleanup)(struct ipath_devdata *);
313	void (*ipath_f_setextled)(struct ipath_devdata *, u64, u64);
314	/* fill out chip-specific fields */
315	int (*ipath_f_get_base_info)(struct ipath_portdata *, void *);
316	/* free irq */
317	void (*ipath_f_free_irq)(struct ipath_devdata *);
318	struct ipath_message_header *(*ipath_f_get_msgheader)
319					(struct ipath_devdata *, __le32 *);
320	void (*ipath_f_config_ports)(struct ipath_devdata *, ushort);
321	int (*ipath_f_get_ib_cfg)(struct ipath_devdata *, int);
322	int (*ipath_f_set_ib_cfg)(struct ipath_devdata *, int, u32);
323	void (*ipath_f_config_jint)(struct ipath_devdata *, u16 , u16);
324	void (*ipath_f_read_counters)(struct ipath_devdata *,
325					struct infinipath_counters *);
326	void (*ipath_f_xgxs_reset)(struct ipath_devdata *);
327	/* per chip actions needed for IB Link up/down changes */
328	int (*ipath_f_ib_updown)(struct ipath_devdata *, int, u64);
329
330	unsigned ipath_lastegr_idx;
331	struct ipath_ibdev *verbs_dev;
332	struct timer_list verbs_timer;
333	/* total dwords sent (summed from counter) */
334	u64 ipath_sword;
335	/* total dwords rcvd (summed from counter) */
336	u64 ipath_rword;
337	/* total packets sent (summed from counter) */
338	u64 ipath_spkts;
339	/* total packets rcvd (summed from counter) */
340	u64 ipath_rpkts;
341	/* ipath_statusp initially points to this. */
342	u64 _ipath_status;
343	/* GUID for this interface, in network order */
344	__be64 ipath_guid;
345	/*
346	 * aggregrate of error bits reported since last cleared, for
347	 * limiting of error reporting
348	 */
349	ipath_err_t ipath_lasterror;
350	/*
351	 * aggregrate of error bits reported since last cleared, for
352	 * limiting of hwerror reporting
353	 */
354	ipath_err_t ipath_lasthwerror;
355	/* errors masked because they occur too fast */
356	ipath_err_t ipath_maskederrs;
357	u64 ipath_lastlinkrecov; /* link recoveries at last ACTIVE */
358	/* these 5 fields are used to establish deltas for IB Symbol
359	 * errors and linkrecovery errors. They can be reported on
360	 * some chips during link negotiation prior to INIT, and with
361	 * DDR when faking DDR negotiations with non-IBTA switches.
362	 * The chip counters are adjusted at driver unload if there is
363	 * a non-zero delta.
364	 */
365	u64 ibdeltainprog;
366	u64 ibsymdelta;
367	u64 ibsymsnap;
368	u64 iblnkerrdelta;
369	u64 iblnkerrsnap;
370
371	/* time in jiffies at which to re-enable maskederrs */
372	unsigned long ipath_unmasktime;
373	/* count of egrfull errors, combined for all ports */
374	u64 ipath_last_tidfull;
375	/* for ipath_qcheck() */
376	u64 ipath_lastport0rcv_cnt;
377	/* template for writing TIDs  */
378	u64 ipath_tidtemplate;
379	/* value to write to free TIDs */
380	u64 ipath_tidinvalid;
381	/* IBA6120 rcv interrupt setup */
382	u64 ipath_rhdrhead_intr_off;
383
384	/* size of memory at ipath_kregbase */
385	u32 ipath_kregsize;
386	/* number of registers used for pioavail */
387	u32 ipath_pioavregs;
388	/* IPATH_POLL, etc. */
389	u32 ipath_flags;
390	/* ipath_flags driver is waiting for */
391	u32 ipath_state_wanted;
392	/* last buffer for user use, first buf for kernel use is this
393	 * index. */
394	u32 ipath_lastport_piobuf;
395	/* is a stats timer active */
396	u32 ipath_stats_timer_active;
397	/* number of interrupts for this device -- saturates... */
398	u32 ipath_int_counter;
399	/* dwords sent read from counter */
400	u32 ipath_lastsword;
401	/* dwords received read from counter */
402	u32 ipath_lastrword;
403	/* sent packets read from counter */
404	u32 ipath_lastspkts;
405	/* received packets read from counter */
406	u32 ipath_lastrpkts;
407	/* pio bufs allocated per port */
408	u32 ipath_pbufsport;
409	/* if remainder on bufs/port, ports < extrabuf get 1 extra */
410	u32 ipath_ports_extrabuf;
411	u32 ipath_pioupd_thresh; /* update threshold, some chips */
412	/*
413	 * number of ports configured as max; zero is set to number chip
414	 * supports, less gives more pio bufs/port, etc.
415	 */
416	u32 ipath_cfgports;
417	/* count of port 0 hdrqfull errors */
418	u32 ipath_p0_hdrqfull;
419	/* port 0 number of receive eager buffers */
420	u32 ipath_p0_rcvegrcnt;
421
422	/*
423	 * index of last piobuffer we used.  Speeds up searching, by
424	 * starting at this point.  Doesn't matter if multiple cpu's use and
425	 * update, last updater is only write that matters.  Whenever it
426	 * wraps, we update shadow copies.  Need a copy per device when we
427	 * get to multiple devices
428	 */
429	u32 ipath_lastpioindex;
430	u32 ipath_lastpioindexl;
431	/* max length of freezemsg */
432	u32 ipath_freezelen;
433	/*
434	 * consecutive times we wanted a PIO buffer but were unable to
435	 * get one
436	 */
437	u32 ipath_consec_nopiobuf;
438	/*
439	 * hint that we should update ipath_pioavailshadow before
440	 * looking for a PIO buffer
441	 */
442	u32 ipath_upd_pio_shadow;
443	/* so we can rewrite it after a chip reset */
444	u32 ipath_pcibar0;
445	/* so we can rewrite it after a chip reset */
446	u32 ipath_pcibar1;
447	u32 ipath_x1_fix_tries;
448	u32 ipath_autoneg_tries;
449	u32 serdes_first_init_done;
450
451	struct ipath_relock {
452		atomic_t ipath_relock_timer_active;
453		struct timer_list ipath_relock_timer;
454		unsigned int ipath_relock_interval; /* in jiffies */
455	} ipath_relock_singleton;
456
457	/* interrupt number */
458	int ipath_irq;
459	/* HT/PCI Vendor ID (here for NodeInfo) */
460	u16 ipath_vendorid;
461	/* HT/PCI Device ID (here for NodeInfo) */
462	u16 ipath_deviceid;
463	/* offset in HT config space of slave/primary interface block */
464	u8 ipath_ht_slave_off;
465	/* for write combining settings */
466	unsigned long ipath_wc_cookie;
467	unsigned long ipath_wc_base;
468	unsigned long ipath_wc_len;
469	/* ref count for each pkey */
470	atomic_t ipath_pkeyrefs[4];
471	/* shadow copy of struct page *'s for exp tid pages */
472	struct page **ipath_pageshadow;
473	/* shadow copy of dma handles for exp tid pages */
474	dma_addr_t *ipath_physshadow;
475	u64 __iomem *ipath_egrtidbase;
476	/* lock to workaround chip bug 9437 and others */
477	spinlock_t ipath_kernel_tid_lock;
478	spinlock_t ipath_user_tid_lock;
479	spinlock_t ipath_sendctrl_lock;
480	/* around ipath_pd and (user ports) port_cnt use (intr vs free) */
481	spinlock_t ipath_uctxt_lock;
482
483	/*
484	 * IPATH_STATUS_*,
485	 * this address is mapped readonly into user processes so they can
486	 * get status cheaply, whenever they want.
487	 */
488	u64 *ipath_statusp;
489	/* freeze msg if hw error put chip in freeze */
490	char *ipath_freezemsg;
491	/* pci access data structure */
492	struct pci_dev *pcidev;
493	struct cdev *user_cdev;
494	struct cdev *diag_cdev;
495	struct device *user_dev;
496	struct device *diag_dev;
497	/* timer used to prevent stats overflow, error throttling, etc. */
498	struct timer_list ipath_stats_timer;
499	/* timer to verify interrupts work, and fallback if possible */
500	struct timer_list ipath_intrchk_timer;
501	void *ipath_dummy_hdrq;	/* used after port close */
502	dma_addr_t ipath_dummy_hdrq_phys;
503
504	/* SendDMA related entries */
505	spinlock_t            ipath_sdma_lock;
506	unsigned long         ipath_sdma_status;
507	unsigned long         ipath_sdma_abort_jiffies;
508	unsigned long         ipath_sdma_abort_intr_timeout;
509	unsigned long         ipath_sdma_buf_jiffies;
510	struct ipath_sdma_desc *ipath_sdma_descq;
511	u64		      ipath_sdma_descq_added;
512	u64		      ipath_sdma_descq_removed;
513	int		      ipath_sdma_desc_nreserved;
514	u16                   ipath_sdma_descq_cnt;
515	u16                   ipath_sdma_descq_tail;
516	u16                   ipath_sdma_descq_head;
517	u16                   ipath_sdma_next_intr;
518	u16                   ipath_sdma_reset_wait;
519	u8                    ipath_sdma_generation;
520	struct tasklet_struct ipath_sdma_abort_task;
521	struct tasklet_struct ipath_sdma_notify_task;
522	struct list_head      ipath_sdma_activelist;
523	struct list_head      ipath_sdma_notifylist;
524	atomic_t              ipath_sdma_vl15_count;
525	struct timer_list     ipath_sdma_vl15_timer;
526
527	dma_addr_t       ipath_sdma_descq_phys;
528	volatile __le64 *ipath_sdma_head_dma;
529	dma_addr_t       ipath_sdma_head_phys;
530
531	unsigned long ipath_ureg_align; /* user register alignment */
532
533	struct delayed_work ipath_autoneg_work;
534	wait_queue_head_t ipath_autoneg_wait;
535
536	/* HoL blocking / user app forward-progress state */
537	unsigned          ipath_hol_state;
538	unsigned          ipath_hol_next;
539	struct timer_list ipath_hol_timer;
540
541	/*
542	 * Shadow copies of registers; size indicates read access size.
543	 * Most of them are readonly, but some are write-only register,
544	 * where we manipulate the bits in the shadow copy, and then write
545	 * the shadow copy to infinipath.
546	 *
547	 * We deliberately make most of these 32 bits, since they have
548	 * restricted range.  For any that we read, we won't to generate 32
549	 * bit accesses, since Opteron will generate 2 separate 32 bit HT
550	 * transactions for a 64 bit read, and we want to avoid unnecessary
551	 * HT transactions.
552	 */
553
554	/* This is the 64 bit group */
555
556	/*
557	 * shadow of pioavail, check to be sure it's large enough at
558	 * init time.
559	 */
560	unsigned long ipath_pioavailshadow[8];
561	/* bitmap of send buffers available for the kernel to use with PIO. */
562	unsigned long ipath_pioavailkernel[8];
563	/* shadow of kr_gpio_out, for rmw ops */
564	u64 ipath_gpio_out;
565	/* shadow the gpio mask register */
566	u64 ipath_gpio_mask;
567	/* shadow the gpio output enable, etc... */
568	u64 ipath_extctrl;
569	/* kr_revision shadow */
570	u64 ipath_revision;
571	/*
572	 * shadow of ibcctrl, for interrupt handling of link changes,
573	 * etc.
574	 */
575	u64 ipath_ibcctrl;
576	/*
577	 * last ibcstatus, to suppress "duplicate" status change messages,
578	 * mostly from 2 to 3
579	 */
580	u64 ipath_lastibcstat;
581	/* hwerrmask shadow */
582	ipath_err_t ipath_hwerrmask;
583	ipath_err_t ipath_errormask; /* errormask shadow */
584	/* interrupt config reg shadow */
585	u64 ipath_intconfig;
586	/* kr_sendpiobufbase value */
587	u64 ipath_piobufbase;
588	/* kr_ibcddrctrl shadow */
589	u64 ipath_ibcddrctrl;
590
591	/* these are the "32 bit" regs */
592
593	/*
594	 * number of GUIDs in the flash for this interface; may need some
595	 * rethinking for setting on other ifaces
596	 */
597	u32 ipath_nguid;
598	/*
599	 * the following two are 32-bit bitmasks, but {test,clear,set}_bit
600	 * all expect bit fields to be "unsigned long"
601	 */
602	/* shadow kr_rcvctrl */
603	unsigned long ipath_rcvctrl;
604	/* shadow kr_sendctrl */
605	unsigned long ipath_sendctrl;
606	/* to not count armlaunch after cancel */
607	unsigned long ipath_lastcancel;
608	/* count cases where special trigger was needed (double write) */
609	unsigned long ipath_spectriggerhit;
610
611	/* value we put in kr_rcvhdrcnt */
612	u32 ipath_rcvhdrcnt;
613	/* value we put in kr_rcvhdrsize */
614	u32 ipath_rcvhdrsize;
615	/* value we put in kr_rcvhdrentsize */
616	u32 ipath_rcvhdrentsize;
617	/* offset of last entry in rcvhdrq */
618	u32 ipath_hdrqlast;
619	/* kr_portcnt value */
620	u32 ipath_portcnt;
621	/* kr_pagealign value */
622	u32 ipath_palign;
623	/* number of "2KB" PIO buffers */
624	u32 ipath_piobcnt2k;
625	/* size in bytes of "2KB" PIO buffers */
626	u32 ipath_piosize2k;
627	/* number of "4KB" PIO buffers */
628	u32 ipath_piobcnt4k;
629	/* size in bytes of "4KB" PIO buffers */
630	u32 ipath_piosize4k;
631	u32 ipath_pioreserved; /* reserved special-inkernel; */
632	/* kr_rcvegrbase value */
633	u32 ipath_rcvegrbase;
634	/* kr_rcvegrcnt value */
635	u32 ipath_rcvegrcnt;
636	/* kr_rcvtidbase value */
637	u32 ipath_rcvtidbase;
638	/* kr_rcvtidcnt value */
639	u32 ipath_rcvtidcnt;
640	/* kr_sendregbase */
641	u32 ipath_sregbase;
642	/* kr_userregbase */
643	u32 ipath_uregbase;
644	/* kr_counterregbase */
645	u32 ipath_cregbase;
646	/* shadow the control register contents */
647	u32 ipath_control;
648	/* PCI revision register (HTC rev on FPGA) */
649	u32 ipath_pcirev;
650
651	/* chip address space used by 4k pio buffers */
652	u32 ipath_4kalign;
653	/* The MTU programmed for this unit */
654	u32 ipath_ibmtu;
655	/*
656	 * The max size IB packet, included IB headers that we can send.
657	 * Starts same as ipath_piosize, but is affected when ibmtu is
658	 * changed, or by size of eager buffers
659	 */
660	u32 ipath_ibmaxlen;
661	/*
662	 * ibmaxlen at init time, limited by chip and by receive buffer
663	 * size.  Not changed after init.
664	 */
665	u32 ipath_init_ibmaxlen;
666	/* size of each rcvegrbuffer */
667	u32 ipath_rcvegrbufsize;
668	/* localbus width (1, 2,4,8,16,32) from config space  */
669	u32 ipath_lbus_width;
670	/* localbus speed (HT: 200,400,800,1000; PCIe 2500) */
671	u32 ipath_lbus_speed;
672	/*
673	 * number of sequential ibcstatus change for polling active/quiet
674	 * (i.e., link not coming up).
675	 */
676	u32 ipath_ibpollcnt;
677	/* low and high portions of MSI capability/vector */
678	u32 ipath_msi_lo;
679	/* saved after PCIe init for restore after reset */
680	u32 ipath_msi_hi;
681	/* MSI data (vector) saved for restore */
682	u16 ipath_msi_data;
683	/* MLID programmed for this instance */
684	u16 ipath_mlid;
685	/* LID programmed for this instance */
686	u16 ipath_lid;
687	/* list of pkeys programmed; 0 if not set */
688	u16 ipath_pkeys[4];
689	/*
690	 * ASCII serial number, from flash, large enough for original
691	 * all digit strings, and longer QLogic serial number format
692	 */
693	u8 ipath_serial[16];
694	/* human readable board version */
695	u8 ipath_boardversion[96];
696	u8 ipath_lbus_info[32]; /* human readable localbus info */
697	/* chip major rev, from ipath_revision */
698	u8 ipath_majrev;
699	/* chip minor rev, from ipath_revision */
700	u8 ipath_minrev;
701	/* board rev, from ipath_revision */
702	u8 ipath_boardrev;
703	/* saved for restore after reset */
704	u8 ipath_pci_cacheline;
705	/* LID mask control */
706	u8 ipath_lmc;
707	/* link width supported */
708	u8 ipath_link_width_supported;
709	/* link speed supported */
710	u8 ipath_link_speed_supported;
711	u8 ipath_link_width_enabled;
712	u8 ipath_link_speed_enabled;
713	u8 ipath_link_width_active;
714	u8 ipath_link_speed_active;
715	/* Rx Polarity inversion (compensate for ~tx on partner) */
716	u8 ipath_rx_pol_inv;
717
718	u8 ipath_r_portenable_shift;
719	u8 ipath_r_intravail_shift;
720	u8 ipath_r_tailupd_shift;
721	u8 ipath_r_portcfg_shift;
722
723	/* unit # of this chip, if present */
724	int ipath_unit;
725
726	/* local link integrity counter */
727	u32 ipath_lli_counter;
728	/* local link integrity errors */
729	u32 ipath_lli_errors;
730	/*
731	 * Above counts only cases where _successive_ LocalLinkIntegrity
732	 * errors were seen in the receive headers of kern-packets.
733	 * Below are the three (monotonically increasing) counters
734	 * maintained via GPIO interrupts on iba6120-rev2.
735	 */
736	u32 ipath_rxfc_unsupvl_errs;
737	u32 ipath_overrun_thresh_errs;
738	u32 ipath_lli_errs;
739
740	/*
741	 * Not all devices managed by a driver instance are the same
742	 * type, so these fields must be per-device.
743	 */
744	u64 ipath_i_bitsextant;
745	ipath_err_t ipath_e_bitsextant;
746	ipath_err_t ipath_hwe_bitsextant;
747
748	/*
749	 * Below should be computable from number of ports,
750	 * since they are never modified.
751	 */
752	u64 ipath_i_rcvavail_mask;
753	u64 ipath_i_rcvurg_mask;
754	u16 ipath_i_rcvurg_shift;
755	u16 ipath_i_rcvavail_shift;
756
757	/*
758	 * Register bits for selecting i2c direction and values, used for
759	 * I2C serial flash.
760	 */
761	u8 ipath_gpio_sda_num;
762	u8 ipath_gpio_scl_num;
763	u8 ipath_i2c_chain_type;
764	u64 ipath_gpio_sda;
765	u64 ipath_gpio_scl;
766
767	/* lock for doing RMW of shadows/regs for ExtCtrl and GPIO */
768	spinlock_t ipath_gpio_lock;
769
770	/*
771	 * IB link and linktraining states and masks that vary per chip in
772	 * some way.  Set at init, to avoid each IB status change interrupt
773	 */
774	u8 ibcs_ls_shift;
775	u8 ibcs_lts_mask;
776	u32 ibcs_mask;
777	u32 ib_init;
778	u32 ib_arm;
779	u32 ib_active;
780
781	u16 ipath_rhf_offset; /* offset of RHF within receive header entry */
782
783	/*
784	 * shift/mask for linkcmd, linkinitcmd, maxpktlen in ibccontol
785	 * reg. Changes for IBA7220
786	 */
787	u8 ibcc_lic_mask; /* LinkInitCmd */
788	u8 ibcc_lc_shift; /* LinkCmd */
789	u8 ibcc_mpl_shift; /* Maxpktlen */
790
791	u8 delay_mult;
792
793	/* used to override LED behavior */
794	u8 ipath_led_override;  /* Substituted for normal value, if non-zero */
795	u16 ipath_led_override_timeoff; /* delta to next timer event */
796	u8 ipath_led_override_vals[2]; /* Alternates per blink-frame */
797	u8 ipath_led_override_phase; /* Just counts, LSB picks from vals[] */
798	atomic_t ipath_led_override_timer_active;
799	/* Used to flash LEDs in override mode */
800	struct timer_list ipath_led_override_timer;
801
802	/* Support (including locks) for EEPROM logging of errors and time */
803	/* control access to actual counters, timer */
804	spinlock_t ipath_eep_st_lock;
805	/* control high-level access to EEPROM */
806	struct mutex ipath_eep_lock;
807	/* Below inc'd by ipath_snap_cntrs(), locked by ipath_eep_st_lock */
808	uint64_t ipath_traffic_wds;
809	/* active time is kept in seconds, but logged in hours */
810	atomic_t ipath_active_time;
811	/* Below are nominal shadow of EEPROM, new since last EEPROM update */
812	uint8_t ipath_eep_st_errs[IPATH_EEP_LOG_CNT];
813	uint8_t ipath_eep_st_new_errs[IPATH_EEP_LOG_CNT];
814	uint16_t ipath_eep_hrs;
815	/*
816	 * masks for which bits of errs, hwerrs that cause
817	 * each of the counters to increment.
818	 */
819	struct ipath_eep_log_mask ipath_eep_st_masks[IPATH_EEP_LOG_CNT];
820
821	/* interrupt mitigation reload register info */
822	u16 ipath_jint_idle_ticks;	/* idle clock ticks */
823	u16 ipath_jint_max_packets;	/* max packets across all ports */
824
825	/*
826	 * lock for access to SerDes, and flags to sequence preset
827	 * versus steady-state. 7220-only at the moment.
828	 */
829	spinlock_t ipath_sdepb_lock;
830	u8 ipath_presets_needed; /* Set if presets to be restored next DOWN */
831};
832
833/* ipath_hol_state values (stopping/starting user proc, send flushing) */
834#define IPATH_HOL_UP       0
835#define IPATH_HOL_DOWN     1
836/* ipath_hol_next toggle values, used when hol_state IPATH_HOL_DOWN */
837#define IPATH_HOL_DOWNSTOP 0
838#define IPATH_HOL_DOWNCONT 1
839
840/* bit positions for sdma_status */
841#define IPATH_SDMA_ABORTING  0
842#define IPATH_SDMA_DISARMED  1
843#define IPATH_SDMA_DISABLED  2
844#define IPATH_SDMA_LAYERBUF  3
845#define IPATH_SDMA_RUNNING  30
846#define IPATH_SDMA_SHUTDOWN 31
847
848/* bit combinations that correspond to abort states */
849#define IPATH_SDMA_ABORT_NONE 0
850#define IPATH_SDMA_ABORT_ABORTING (1UL << IPATH_SDMA_ABORTING)
851#define IPATH_SDMA_ABORT_DISARMED ((1UL << IPATH_SDMA_ABORTING) | \
852	(1UL << IPATH_SDMA_DISARMED))
853#define IPATH_SDMA_ABORT_DISABLED ((1UL << IPATH_SDMA_ABORTING) | \
854	(1UL << IPATH_SDMA_DISABLED))
855#define IPATH_SDMA_ABORT_ABORTED ((1UL << IPATH_SDMA_ABORTING) | \
856	(1UL << IPATH_SDMA_DISARMED) | (1UL << IPATH_SDMA_DISABLED))
857#define IPATH_SDMA_ABORT_MASK ((1UL<<IPATH_SDMA_ABORTING) | \
858	(1UL << IPATH_SDMA_DISARMED) | (1UL << IPATH_SDMA_DISABLED))
859
860#define IPATH_SDMA_BUF_NONE 0
861#define IPATH_SDMA_BUF_MASK (1UL<<IPATH_SDMA_LAYERBUF)
862
863/* Private data for file operations */
864struct ipath_filedata {
865	struct ipath_portdata *pd;
866	unsigned subport;
867	unsigned tidcursor;
868	struct ipath_user_sdma_queue *pq;
869};
870extern struct list_head ipath_dev_list;
871extern spinlock_t ipath_devs_lock;
872extern struct ipath_devdata *ipath_lookup(int unit);
873
874int ipath_init_chip(struct ipath_devdata *, int);
875int ipath_enable_wc(struct ipath_devdata *dd);
876void ipath_disable_wc(struct ipath_devdata *dd);
877int ipath_count_units(int *npresentp, int *nupp, int *maxportsp);
878void ipath_shutdown_device(struct ipath_devdata *);
879void ipath_clear_freeze(struct ipath_devdata *);
880
881struct file_operations;
882int ipath_cdev_init(int minor, char *name, const struct file_operations *fops,
883		    struct cdev **cdevp, struct device **devp);
884void ipath_cdev_cleanup(struct cdev **cdevp,
885			struct device **devp);
886
887int ipath_diag_add(struct ipath_devdata *);
888void ipath_diag_remove(struct ipath_devdata *);
889
890extern wait_queue_head_t ipath_state_wait;
891
892int ipath_user_add(struct ipath_devdata *dd);
893void ipath_user_remove(struct ipath_devdata *dd);
894
895struct sk_buff *ipath_alloc_skb(struct ipath_devdata *dd, gfp_t);
896
897extern int ipath_diag_inuse;
898
899irqreturn_t ipath_intr(int irq, void *devid);
900int ipath_decode_err(struct ipath_devdata *dd, char *buf, size_t blen,
901		     ipath_err_t err);
902#if __IPATH_INFO || __IPATH_DBG
903extern const char *ipath_ibcstatus_str[];
904#endif
905
906/* clean up any per-chip chip-specific stuff */
907void ipath_chip_cleanup(struct ipath_devdata *);
908/* clean up any chip type-specific stuff */
909void ipath_chip_done(void);
910
911void ipath_disarm_piobufs(struct ipath_devdata *, unsigned first,
912			  unsigned cnt);
913void ipath_cancel_sends(struct ipath_devdata *, int);
914
915int ipath_create_rcvhdrq(struct ipath_devdata *, struct ipath_portdata *);
916void ipath_free_pddata(struct ipath_devdata *, struct ipath_portdata *);
917
918int ipath_parse_ushort(const char *str, unsigned short *valp);
919
920void ipath_kreceive(struct ipath_portdata *);
921int ipath_setrcvhdrsize(struct ipath_devdata *, unsigned);
922int ipath_reset_device(int);
923void ipath_get_faststats(unsigned long);
924int ipath_wait_linkstate(struct ipath_devdata *, u32, int);
925int ipath_set_linkstate(struct ipath_devdata *, u8);
926int ipath_set_mtu(struct ipath_devdata *, u16);
927int ipath_set_lid(struct ipath_devdata *, u32, u8);
928int ipath_set_rx_pol_inv(struct ipath_devdata *dd, u8 new_pol_inv);
929void ipath_enable_armlaunch(struct ipath_devdata *);
930void ipath_disable_armlaunch(struct ipath_devdata *);
931void ipath_hol_down(struct ipath_devdata *);
932void ipath_hol_up(struct ipath_devdata *);
933void ipath_hol_event(unsigned long);
934void ipath_toggle_rclkrls(struct ipath_devdata *);
935void ipath_sd7220_clr_ibpar(struct ipath_devdata *);
936void ipath_set_relock_poll(struct ipath_devdata *, int);
937void ipath_shutdown_relock_poll(struct ipath_devdata *);
938
939/* for use in system calls, where we want to know device type, etc. */
940#define port_fp(fp) ((struct ipath_filedata *)(fp)->private_data)->pd
941#define subport_fp(fp) \
942	((struct ipath_filedata *)(fp)->private_data)->subport
943#define tidcursor_fp(fp) \
944	((struct ipath_filedata *)(fp)->private_data)->tidcursor
945#define user_sdma_queue_fp(fp) \
946	((struct ipath_filedata *)(fp)->private_data)->pq
947
948/*
949 * values for ipath_flags
950 */
951		/* chip can report link latency (IB 1.2) */
952#define IPATH_HAS_LINK_LATENCY 0x1
953		/* The chip is up and initted */
954#define IPATH_INITTED       0x2
955		/* set if any user code has set kr_rcvhdrsize */
956#define IPATH_RCVHDRSZ_SET  0x4
957		/* The chip is present and valid for accesses */
958#define IPATH_PRESENT       0x8
959		/* HT link0 is only 8 bits wide, ignore upper byte crc
960		 * errors, etc. */
961#define IPATH_8BIT_IN_HT0   0x10
962		/* HT link1 is only 8 bits wide, ignore upper byte crc
963		 * errors, etc. */
964#define IPATH_8BIT_IN_HT1   0x20
965		/* The link is down */
966#define IPATH_LINKDOWN      0x40
967		/* The link level is up (0x11) */
968#define IPATH_LINKINIT      0x80
969		/* The link is in the armed (0x21) state */
970#define IPATH_LINKARMED     0x100
971		/* The link is in the active (0x31) state */
972#define IPATH_LINKACTIVE    0x200
973		/* link current state is unknown */
974#define IPATH_LINKUNK       0x400
975		/* Write combining flush needed for PIO */
976#define IPATH_PIO_FLUSH_WC  0x1000
977		/* DMA Receive tail pointer */
978#define IPATH_NODMA_RTAIL   0x2000
979		/* no IB cable, or no device on IB cable */
980#define IPATH_NOCABLE       0x4000
981		/* Supports port zero per packet receive interrupts via
982		 * GPIO */
983#define IPATH_GPIO_INTR     0x8000
984		/* uses the coded 4byte TID, not 8 byte */
985#define IPATH_4BYTE_TID     0x10000
986		/* packet/word counters are 32 bit, else those 4 counters
987		 * are 64bit */
988#define IPATH_32BITCOUNTERS 0x20000
989		/* Interrupt register is 64 bits */
990#define IPATH_INTREG_64     0x40000
991		/* can miss port0 rx interrupts */
992#define IPATH_DISABLED      0x80000 /* administratively disabled */
993		/* Use GPIO interrupts for new counters */
994#define IPATH_GPIO_ERRINTRS 0x100000
995#define IPATH_SWAP_PIOBUFS  0x200000
996		/* Supports Send DMA */
997#define IPATH_HAS_SEND_DMA  0x400000
998		/* Supports Send Count (not just word count) in PBC */
999#define IPATH_HAS_PBC_CNT   0x800000
1000		/* Suppress heartbeat, even if turning off loopback */
1001#define IPATH_NO_HRTBT      0x1000000
1002#define IPATH_HAS_THRESH_UPDATE 0x4000000
1003#define IPATH_HAS_MULT_IB_SPEED 0x8000000
1004#define IPATH_IB_AUTONEG_INPROG 0x10000000
1005#define IPATH_IB_AUTONEG_FAILED 0x20000000
1006		/* Linkdown-disable intentionally, Do not attempt to bring up */
1007#define IPATH_IB_LINK_DISABLED 0x40000000
1008#define IPATH_IB_FORCE_NOTIFY 0x80000000 /* force notify on next ib change */
1009
1010/* Bits in GPIO for the added interrupts */
1011#define IPATH_GPIO_PORT0_BIT 2
1012#define IPATH_GPIO_RXUVL_BIT 3
1013#define IPATH_GPIO_OVRUN_BIT 4
1014#define IPATH_GPIO_LLI_BIT 5
1015#define IPATH_GPIO_ERRINTR_MASK 0x38
1016
1017/* portdata flag bit offsets */
1018		/* waiting for a packet to arrive */
1019#define IPATH_PORT_WAITING_RCV   2
1020		/* master has not finished initializing */
1021#define IPATH_PORT_MASTER_UNINIT 4
1022		/* waiting for an urgent packet to arrive */
1023#define IPATH_PORT_WAITING_URG 5
1024
1025/* free up any allocated data at closes */
1026void ipath_free_data(struct ipath_portdata *dd);
1027u32 __iomem *ipath_getpiobuf(struct ipath_devdata *, u32, u32 *);
1028void ipath_chg_pioavailkernel(struct ipath_devdata *dd, unsigned start,
1029				unsigned len, int avail);
1030void ipath_init_iba6110_funcs(struct ipath_devdata *);
1031void ipath_get_eeprom_info(struct ipath_devdata *);
1032int ipath_update_eeprom_log(struct ipath_devdata *dd);
1033void ipath_inc_eeprom_err(struct ipath_devdata *dd, u32 eidx, u32 incr);
1034u64 ipath_snap_cntr(struct ipath_devdata *, ipath_creg);
1035void ipath_disarm_senderrbufs(struct ipath_devdata *);
1036void ipath_force_pio_avail_update(struct ipath_devdata *);
1037void signal_ib_event(struct ipath_devdata *dd, enum ib_event_type ev);
1038
1039/*
1040 * Set LED override, only the two LSBs have "public" meaning, but
1041 * any non-zero value substitutes them for the Link and LinkTrain
1042 * LED states.
1043 */
1044#define IPATH_LED_PHYS 1 /* Physical (linktraining) GREEN LED */
1045#define IPATH_LED_LOG 2  /* Logical (link) YELLOW LED */
1046void ipath_set_led_override(struct ipath_devdata *dd, unsigned int val);
1047
1048/* send dma routines */
1049int setup_sdma(struct ipath_devdata *);
1050void teardown_sdma(struct ipath_devdata *);
1051void ipath_restart_sdma(struct ipath_devdata *);
1052void ipath_sdma_intr(struct ipath_devdata *);
1053int ipath_sdma_verbs_send(struct ipath_devdata *, struct ipath_sge_state *,
1054			  u32, struct ipath_verbs_txreq *);
1055/* ipath_sdma_lock should be locked before calling this. */
1056int ipath_sdma_make_progress(struct ipath_devdata *dd);
1057
1058/* must be called under ipath_sdma_lock */
1059static inline u16 ipath_sdma_descq_freecnt(const struct ipath_devdata *dd)
1060{
1061	return dd->ipath_sdma_descq_cnt -
1062		(dd->ipath_sdma_descq_added - dd->ipath_sdma_descq_removed) -
1063		1 - dd->ipath_sdma_desc_nreserved;
1064}
1065
1066static inline void ipath_sdma_desc_reserve(struct ipath_devdata *dd, u16 cnt)
1067{
1068	dd->ipath_sdma_desc_nreserved += cnt;
1069}
1070
1071static inline void ipath_sdma_desc_unreserve(struct ipath_devdata *dd, u16 cnt)
1072{
1073	dd->ipath_sdma_desc_nreserved -= cnt;
1074}
1075
1076/*
1077 * number of words used for protocol header if not set by ipath_userinit();
1078 */
1079#define IPATH_DFLT_RCVHDRSIZE 9
1080
1081int ipath_get_user_pages(unsigned long, size_t, struct page **);
1082void ipath_release_user_pages(struct page **, size_t);
1083void ipath_release_user_pages_on_close(struct page **, size_t);
1084int ipath_eeprom_read(struct ipath_devdata *, u8, void *, int);
1085int ipath_eeprom_write(struct ipath_devdata *, u8, const void *, int);
1086int ipath_tempsense_read(struct ipath_devdata *, u8 regnum);
1087int ipath_tempsense_write(struct ipath_devdata *, u8 regnum, u8 data);
1088
1089/* these are used for the registers that vary with port */
1090void ipath_write_kreg_port(const struct ipath_devdata *, ipath_kreg,
1091			   unsigned, u64);
1092
1093/*
1094 * We could have a single register get/put routine, that takes a group type,
1095 * but this is somewhat clearer and cleaner.  It also gives us some error
1096 * checking.  64 bit register reads should always work, but are inefficient
1097 * on opteron (the northbridge always generates 2 separate HT 32 bit reads),
1098 * so we use kreg32 wherever possible.  User register and counter register
1099 * reads are always 32 bit reads, so only one form of those routines.
1100 */
1101
1102/*
1103 * At the moment, none of the s-registers are writable, so no
1104 * ipath_write_sreg().
1105 */
1106
1107/**
1108 * ipath_read_ureg32 - read 32-bit virtualized per-port register
1109 * @dd: device
1110 * @regno: register number
1111 * @port: port number
1112 *
1113 * Return the contents of a register that is virtualized to be per port.
1114 * Returns -1 on errors (not distinguishable from valid contents at
1115 * runtime; we may add a separate error variable at some point).
1116 */
1117static inline u32 ipath_read_ureg32(const struct ipath_devdata *dd,
1118				    ipath_ureg regno, int port)
1119{
1120	if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT))
1121		return 0;
1122
1123	return readl(regno + (u64 __iomem *)
1124		     (dd->ipath_uregbase +
1125		      (char __iomem *)dd->ipath_kregbase +
1126		      dd->ipath_ureg_align * port));
1127}
1128
1129/**
1130 * ipath_write_ureg - write 32-bit virtualized per-port register
1131 * @dd: device
1132 * @regno: register number
1133 * @value: value
1134 * @port: port
1135 *
1136 * Write the contents of a register that is virtualized to be per port.
1137 */
1138static inline void ipath_write_ureg(const struct ipath_devdata *dd,
1139				    ipath_ureg regno, u64 value, int port)
1140{
1141	u64 __iomem *ubase = (u64 __iomem *)
1142		(dd->ipath_uregbase + (char __iomem *) dd->ipath_kregbase +
1143		 dd->ipath_ureg_align * port);
1144	if (dd->ipath_kregbase)
1145		writeq(value, &ubase[regno]);
1146}
1147
1148static inline u32 ipath_read_kreg32(const struct ipath_devdata *dd,
1149				    ipath_kreg regno)
1150{
1151	if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT))
1152		return -1;
1153	return readl((u32 __iomem *) & dd->ipath_kregbase[regno]);
1154}
1155
1156static inline u64 ipath_read_kreg64(const struct ipath_devdata *dd,
1157				    ipath_kreg regno)
1158{
1159	if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT))
1160		return -1;
1161
1162	return readq(&dd->ipath_kregbase[regno]);
1163}
1164
1165static inline void ipath_write_kreg(const struct ipath_devdata *dd,
1166				    ipath_kreg regno, u64 value)
1167{
1168	if (dd->ipath_kregbase)
1169		writeq(value, &dd->ipath_kregbase[regno]);
1170}
1171
1172static inline u64 ipath_read_creg(const struct ipath_devdata *dd,
1173				  ipath_sreg regno)
1174{
1175	if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT))
1176		return 0;
1177
1178	return readq(regno + (u64 __iomem *)
1179		     (dd->ipath_cregbase +
1180		      (char __iomem *)dd->ipath_kregbase));
1181}
1182
1183static inline u32 ipath_read_creg32(const struct ipath_devdata *dd,
1184					 ipath_sreg regno)
1185{
1186	if (!dd->ipath_kregbase || !(dd->ipath_flags & IPATH_PRESENT))
1187		return 0;
1188	return readl(regno + (u64 __iomem *)
1189		     (dd->ipath_cregbase +
1190		      (char __iomem *)dd->ipath_kregbase));
1191}
1192
1193static inline void ipath_write_creg(const struct ipath_devdata *dd,
1194				    ipath_creg regno, u64 value)
1195{
1196	if (dd->ipath_kregbase)
1197		writeq(value, regno + (u64 __iomem *)
1198		       (dd->ipath_cregbase +
1199			(char __iomem *)dd->ipath_kregbase));
1200}
1201
1202static inline void ipath_clear_rcvhdrtail(const struct ipath_portdata *pd)
1203{
1204	*((u64 *) pd->port_rcvhdrtail_kvaddr) = 0ULL;
1205}
1206
1207static inline u32 ipath_get_rcvhdrtail(const struct ipath_portdata *pd)
1208{
1209	return (u32) le64_to_cpu(*((volatile __le64 *)
1210				pd->port_rcvhdrtail_kvaddr));
1211}
1212
1213static inline u32 ipath_get_hdrqtail(const struct ipath_portdata *pd)
1214{
1215	const struct ipath_devdata *dd = pd->port_dd;
1216	u32 hdrqtail;
1217
1218	if (dd->ipath_flags & IPATH_NODMA_RTAIL) {
1219		__le32 *rhf_addr;
1220		u32 seq;
1221
1222		rhf_addr = (__le32 *) pd->port_rcvhdrq +
1223			pd->port_head + dd->ipath_rhf_offset;
1224		seq = ipath_hdrget_seq(rhf_addr);
1225		hdrqtail = pd->port_head;
1226		if (seq == pd->port_seq_cnt)
1227			hdrqtail++;
1228	} else
1229		hdrqtail = ipath_get_rcvhdrtail(pd);
1230
1231	return hdrqtail;
1232}
1233
1234static inline u64 ipath_read_ireg(const struct ipath_devdata *dd, ipath_kreg r)
1235{
1236	return (dd->ipath_flags & IPATH_INTREG_64) ?
1237		ipath_read_kreg64(dd, r) : ipath_read_kreg32(dd, r);
1238}
1239
1240/*
1241 * from contents of IBCStatus (or a saved copy), return linkstate
1242 * Report ACTIVE_DEFER as ACTIVE, because we treat them the same
1243 * everywhere, anyway (and should be, for almost all purposes).
1244 */
1245static inline u32 ipath_ib_linkstate(struct ipath_devdata *dd, u64 ibcs)
1246{
1247	u32 state = (u32)(ibcs >> dd->ibcs_ls_shift) &
1248		INFINIPATH_IBCS_LINKSTATE_MASK;
1249	if (state == INFINIPATH_IBCS_L_STATE_ACT_DEFER)
1250		state = INFINIPATH_IBCS_L_STATE_ACTIVE;
1251	return state;
1252}
1253
1254/* from contents of IBCStatus (or a saved copy), return linktrainingstate */
1255static inline u32 ipath_ib_linktrstate(struct ipath_devdata *dd, u64 ibcs)
1256{
1257	return (u32)(ibcs >> INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) &
1258		dd->ibcs_lts_mask;
1259}
1260
1261/*
1262 * from contents of IBCStatus (or a saved copy), return logical link state
1263 * combination of link state and linktraining state (down, active, init,
1264 * arm, etc.
1265 */
1266static inline u32 ipath_ib_state(struct ipath_devdata *dd, u64 ibcs)
1267{
1268	u32 ibs;
1269	ibs = (u32)(ibcs >> INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) &
1270		dd->ibcs_lts_mask;
1271	ibs |= (u32)(ibcs &
1272		(INFINIPATH_IBCS_LINKSTATE_MASK << dd->ibcs_ls_shift));
1273	return ibs;
1274}
1275
1276/*
1277 * sysfs interface.
1278 */
1279
1280struct device_driver;
1281
1282extern const char ib_ipath_version[];
1283
1284extern const struct attribute_group *ipath_driver_attr_groups[];
1285
1286int ipath_device_create_group(struct device *, struct ipath_devdata *);
1287void ipath_device_remove_group(struct device *, struct ipath_devdata *);
1288int ipath_expose_reset(struct device *);
1289
1290int ipath_init_ipathfs(void);
1291void ipath_exit_ipathfs(void);
1292int ipathfs_add_device(struct ipath_devdata *);
1293int ipathfs_remove_device(struct ipath_devdata *);
1294
1295/*
1296 * dma_addr wrappers - all 0's invalid for hw
1297 */
1298dma_addr_t ipath_map_page(struct pci_dev *, struct page *, unsigned long,
1299			  size_t, int);
1300dma_addr_t ipath_map_single(struct pci_dev *, void *, size_t, int);
1301const char *ipath_get_unit_name(int unit);
1302
1303/*
1304 * Flush write combining store buffers (if present) and perform a write
1305 * barrier.
1306 */
1307#if defined(CONFIG_X86_64)
1308#define ipath_flush_wc() asm volatile("sfence" ::: "memory")
1309#else
1310#define ipath_flush_wc() wmb()
1311#endif
1312
1313extern unsigned ipath_debug; /* debugging bit mask */
1314extern unsigned ipath_linkrecovery;
1315extern unsigned ipath_mtu4096;
1316extern struct mutex ipath_mutex;
1317
1318#define IPATH_DRV_NAME		"ib_ipath"
1319#define IPATH_MAJOR		233
1320#define IPATH_USER_MINOR_BASE	0
1321#define IPATH_DIAGPKT_MINOR	127
1322#define IPATH_DIAG_MINOR_BASE	129
1323#define IPATH_NMINORS		255
1324
1325#define ipath_dev_err(dd,fmt,...) \
1326	do { \
1327		const struct ipath_devdata *__dd = (dd); \
1328		if (__dd->pcidev) \
1329			dev_err(&__dd->pcidev->dev, "%s: " fmt, \
1330				ipath_get_unit_name(__dd->ipath_unit), \
1331				##__VA_ARGS__); \
1332		else \
1333			printk(KERN_ERR IPATH_DRV_NAME ": %s: " fmt, \
1334			       ipath_get_unit_name(__dd->ipath_unit), \
1335			       ##__VA_ARGS__); \
1336	} while (0)
1337
1338#if _IPATH_DEBUGGING
1339
1340# define __IPATH_DBG_WHICH(which,fmt,...) \
1341	do { \
1342		if (unlikely(ipath_debug & (which))) \
1343			printk(KERN_DEBUG IPATH_DRV_NAME ": %s: " fmt, \
1344			       __func__,##__VA_ARGS__); \
1345	} while(0)
1346
1347# define ipath_dbg(fmt,...) \
1348	__IPATH_DBG_WHICH(__IPATH_DBG,fmt,##__VA_ARGS__)
1349# define ipath_cdbg(which,fmt,...) \
1350	__IPATH_DBG_WHICH(__IPATH_##which##DBG,fmt,##__VA_ARGS__)
1351
1352#else /* ! _IPATH_DEBUGGING */
1353
1354# define ipath_dbg(fmt,...)
1355# define ipath_cdbg(which,fmt,...)
1356
1357#endif /* _IPATH_DEBUGGING */
1358
1359/*
1360 * this is used for formatting hw error messages...
1361 */
1362struct ipath_hwerror_msgs {
1363	u64 mask;
1364	const char *msg;
1365};
1366
1367#define INFINIPATH_HWE_MSG(a, b) { .mask = INFINIPATH_HWE_##a, .msg = b }
1368
1369/* in ipath_intr.c... */
1370void ipath_format_hwerrors(u64 hwerrs,
1371			   const struct ipath_hwerror_msgs *hwerrmsgs,
1372			   size_t nhwerrmsgs,
1373			   char *msg, size_t lmsg);
1374
1375#endif				/* _IPATH_KERNEL_H */
1376