1#ifndef LINUX_BCMA_DRIVER_CC_H_ 2#define LINUX_BCMA_DRIVER_CC_H_ 3 4#include <linux/platform_device.h> 5#include <linux/gpio.h> 6 7/** ChipCommon core registers. **/ 8#define BCMA_CC_ID 0x0000 9#define BCMA_CC_ID_ID 0x0000FFFF 10#define BCMA_CC_ID_ID_SHIFT 0 11#define BCMA_CC_ID_REV 0x000F0000 12#define BCMA_CC_ID_REV_SHIFT 16 13#define BCMA_CC_ID_PKG 0x00F00000 14#define BCMA_CC_ID_PKG_SHIFT 20 15#define BCMA_CC_ID_NRCORES 0x0F000000 16#define BCMA_CC_ID_NRCORES_SHIFT 24 17#define BCMA_CC_ID_TYPE 0xF0000000 18#define BCMA_CC_ID_TYPE_SHIFT 28 19#define BCMA_CC_CAP 0x0004 /* Capabilities */ 20#define BCMA_CC_CAP_NRUART 0x00000003 /* # of UARTs */ 21#define BCMA_CC_CAP_MIPSEB 0x00000004 /* MIPS in BigEndian Mode */ 22#define BCMA_CC_CAP_UARTCLK 0x00000018 /* UART clock select */ 23#define BCMA_CC_CAP_UARTCLK_INT 0x00000008 /* UARTs are driven by internal divided clock */ 24#define BCMA_CC_CAP_UARTGPIO 0x00000020 /* UARTs on GPIO 15-12 */ 25#define BCMA_CC_CAP_EXTBUS 0x000000C0 /* External buses present */ 26#define BCMA_CC_CAP_FLASHT 0x00000700 /* Flash Type */ 27#define BCMA_CC_FLASHT_NONE 0x00000000 /* No flash */ 28#define BCMA_CC_FLASHT_STSER 0x00000100 /* ST serial flash */ 29#define BCMA_CC_FLASHT_ATSER 0x00000200 /* Atmel serial flash */ 30#define BCMA_CC_FLASHT_NAND 0x00000300 /* NAND flash */ 31#define BCMA_CC_FLASHT_PARA 0x00000700 /* Parallel flash */ 32#define BCMA_CC_CAP_PLLT 0x00038000 /* PLL Type */ 33#define BCMA_PLLTYPE_NONE 0x00000000 34#define BCMA_PLLTYPE_1 0x00010000 /* 48Mhz base, 3 dividers */ 35#define BCMA_PLLTYPE_2 0x00020000 /* 48Mhz, 4 dividers */ 36#define BCMA_PLLTYPE_3 0x00030000 /* 25Mhz, 2 dividers */ 37#define BCMA_PLLTYPE_4 0x00008000 /* 48Mhz, 4 dividers */ 38#define BCMA_PLLTYPE_5 0x00018000 /* 25Mhz, 4 dividers */ 39#define BCMA_PLLTYPE_6 0x00028000 /* 100/200 or 120/240 only */ 40#define BCMA_PLLTYPE_7 0x00038000 /* 25Mhz, 4 dividers */ 41#define BCMA_CC_CAP_PCTL 0x00040000 /* Power Control */ 42#define BCMA_CC_CAP_OTPS 0x00380000 /* OTP size */ 43#define BCMA_CC_CAP_OTPS_SHIFT 19 44#define BCMA_CC_CAP_OTPS_BASE 5 45#define BCMA_CC_CAP_JTAGM 0x00400000 /* JTAG master present */ 46#define BCMA_CC_CAP_BROM 0x00800000 /* Internal boot ROM active */ 47#define BCMA_CC_CAP_64BIT 0x08000000 /* 64-bit Backplane */ 48#define BCMA_CC_CAP_PMU 0x10000000 /* PMU available (rev >= 20) */ 49#define BCMA_CC_CAP_ECI 0x20000000 /* ECI available (rev >= 20) */ 50#define BCMA_CC_CAP_SPROM 0x40000000 /* SPROM present */ 51#define BCMA_CC_CAP_NFLASH 0x80000000 /* NAND flash present (rev >= 35 or BCM4706?) */ 52#define BCMA_CC_CORECTL 0x0008 53#define BCMA_CC_CORECTL_UARTCLK0 0x00000001 /* Drive UART with internal clock */ 54#define BCMA_CC_CORECTL_SE 0x00000002 /* sync clk out enable (corerev >= 3) */ 55#define BCMA_CC_CORECTL_UARTCLKEN 0x00000008 /* UART clock enable (rev >= 21) */ 56#define BCMA_CC_BIST 0x000C 57#define BCMA_CC_OTPS 0x0010 /* OTP status */ 58#define BCMA_CC_OTPS_PROGFAIL 0x80000000 59#define BCMA_CC_OTPS_PROTECT 0x00000007 60#define BCMA_CC_OTPS_HW_PROTECT 0x00000001 61#define BCMA_CC_OTPS_SW_PROTECT 0x00000002 62#define BCMA_CC_OTPS_CID_PROTECT 0x00000004 63#define BCMA_CC_OTPS_GU_PROG_IND 0x00000F00 /* General Use programmed indication */ 64#define BCMA_CC_OTPS_GU_PROG_IND_SHIFT 8 65#define BCMA_CC_OTPS_GU_PROG_HW 0x00000100 /* HW region programmed */ 66#define BCMA_CC_OTPC 0x0014 /* OTP control */ 67#define BCMA_CC_OTPC_RECWAIT 0xFF000000 68#define BCMA_CC_OTPC_PROGWAIT 0x00FFFF00 69#define BCMA_CC_OTPC_PRW_SHIFT 8 70#define BCMA_CC_OTPC_MAXFAIL 0x00000038 71#define BCMA_CC_OTPC_VSEL 0x00000006 72#define BCMA_CC_OTPC_SELVL 0x00000001 73#define BCMA_CC_OTPP 0x0018 /* OTP prog */ 74#define BCMA_CC_OTPP_COL 0x000000FF 75#define BCMA_CC_OTPP_ROW 0x0000FF00 76#define BCMA_CC_OTPP_ROW_SHIFT 8 77#define BCMA_CC_OTPP_READERR 0x10000000 78#define BCMA_CC_OTPP_VALUE 0x20000000 79#define BCMA_CC_OTPP_READ 0x40000000 80#define BCMA_CC_OTPP_START 0x80000000 81#define BCMA_CC_OTPP_BUSY 0x80000000 82#define BCMA_CC_OTPL 0x001C /* OTP layout */ 83#define BCMA_CC_OTPL_GURGN_OFFSET 0x00000FFF /* offset of general use region */ 84#define BCMA_CC_IRQSTAT 0x0020 85#define BCMA_CC_IRQMASK 0x0024 86#define BCMA_CC_IRQ_GPIO 0x00000001 /* gpio intr */ 87#define BCMA_CC_IRQ_EXT 0x00000002 /* ro: ext intr pin (corerev >= 3) */ 88#define BCMA_CC_IRQ_WDRESET 0x80000000 /* watchdog reset occurred */ 89#define BCMA_CC_CHIPCTL 0x0028 /* Rev >= 11 only */ 90#define BCMA_CC_CHIPSTAT 0x002C /* Rev >= 11 only */ 91#define BCMA_CC_CHIPST_4313_SPROM_PRESENT 1 92#define BCMA_CC_CHIPST_4313_OTP_PRESENT 2 93#define BCMA_CC_CHIPST_4331_SPROM_PRESENT 2 94#define BCMA_CC_CHIPST_4331_OTP_PRESENT 4 95#define BCMA_CC_CHIPST_43228_ILP_DIV_EN 0x00000001 96#define BCMA_CC_CHIPST_43228_OTP_PRESENT 0x00000002 97#define BCMA_CC_CHIPST_43228_SERDES_REFCLK_PADSEL 0x00000004 98#define BCMA_CC_CHIPST_43228_SDIO_MODE 0x00000008 99#define BCMA_CC_CHIPST_43228_SDIO_OTP_PRESENT 0x00000010 100#define BCMA_CC_CHIPST_43228_SDIO_RESET 0x00000020 101#define BCMA_CC_CHIPST_4706_PKG_OPTION BIT(0) /* 0: full-featured package 1: low-cost package */ 102#define BCMA_CC_CHIPST_4706_SFLASH_PRESENT BIT(1) /* 0: parallel, 1: serial flash is present */ 103#define BCMA_CC_CHIPST_4706_SFLASH_TYPE BIT(2) /* 0: 8b-p/ST-s flash, 1: 16b-p/Atmal-s flash */ 104#define BCMA_CC_CHIPST_4706_MIPS_BENDIAN BIT(3) /* 0: little, 1: big endian */ 105#define BCMA_CC_CHIPST_4706_PCIE1_DISABLE BIT(5) /* PCIE1 enable strap pin */ 106#define BCMA_CC_CHIPST_5357_NAND_BOOT BIT(4) /* NAND boot, valid for CC rev 38 and/or BCM5357 */ 107#define BCMA_CC_CHIPST_4360_XTAL_40MZ 0x00000001 108#define BCMA_CC_JCMD 0x0030 /* Rev >= 10 only */ 109#define BCMA_CC_JCMD_START 0x80000000 110#define BCMA_CC_JCMD_BUSY 0x80000000 111#define BCMA_CC_JCMD_PAUSE 0x40000000 112#define BCMA_CC_JCMD0_ACC_MASK 0x0000F000 113#define BCMA_CC_JCMD0_ACC_IRDR 0x00000000 114#define BCMA_CC_JCMD0_ACC_DR 0x00001000 115#define BCMA_CC_JCMD0_ACC_IR 0x00002000 116#define BCMA_CC_JCMD0_ACC_RESET 0x00003000 117#define BCMA_CC_JCMD0_ACC_IRPDR 0x00004000 118#define BCMA_CC_JCMD0_ACC_PDR 0x00005000 119#define BCMA_CC_JCMD0_IRW_MASK 0x00000F00 120#define BCMA_CC_JCMD_ACC_MASK 0x000F0000 /* Changes for corerev 11 */ 121#define BCMA_CC_JCMD_ACC_IRDR 0x00000000 122#define BCMA_CC_JCMD_ACC_DR 0x00010000 123#define BCMA_CC_JCMD_ACC_IR 0x00020000 124#define BCMA_CC_JCMD_ACC_RESET 0x00030000 125#define BCMA_CC_JCMD_ACC_IRPDR 0x00040000 126#define BCMA_CC_JCMD_ACC_PDR 0x00050000 127#define BCMA_CC_JCMD_IRW_MASK 0x00001F00 128#define BCMA_CC_JCMD_IRW_SHIFT 8 129#define BCMA_CC_JCMD_DRW_MASK 0x0000003F 130#define BCMA_CC_JIR 0x0034 /* Rev >= 10 only */ 131#define BCMA_CC_JDR 0x0038 /* Rev >= 10 only */ 132#define BCMA_CC_JCTL 0x003C /* Rev >= 10 only */ 133#define BCMA_CC_JCTL_FORCE_CLK 4 /* Force clock */ 134#define BCMA_CC_JCTL_EXT_EN 2 /* Enable external targets */ 135#define BCMA_CC_JCTL_EN 1 /* Enable Jtag master */ 136#define BCMA_CC_FLASHCTL 0x0040 137/* Start/busy bit in flashcontrol */ 138#define BCMA_CC_FLASHCTL_OPCODE 0x000000ff 139#define BCMA_CC_FLASHCTL_ACTION 0x00000700 140#define BCMA_CC_FLASHCTL_CS_ACTIVE 0x00001000 /* Chip Select Active, rev >= 20 */ 141#define BCMA_CC_FLASHCTL_START 0x80000000 142#define BCMA_CC_FLASHCTL_BUSY BCMA_CC_FLASHCTL_START 143/* Flashcontrol action + opcodes for ST flashes */ 144#define BCMA_CC_FLASHCTL_ST_WREN 0x0006 /* Write Enable */ 145#define BCMA_CC_FLASHCTL_ST_WRDIS 0x0004 /* Write Disable */ 146#define BCMA_CC_FLASHCTL_ST_RDSR 0x0105 /* Read Status Register */ 147#define BCMA_CC_FLASHCTL_ST_WRSR 0x0101 /* Write Status Register */ 148#define BCMA_CC_FLASHCTL_ST_READ 0x0303 /* Read Data Bytes */ 149#define BCMA_CC_FLASHCTL_ST_PP 0x0302 /* Page Program */ 150#define BCMA_CC_FLASHCTL_ST_SE 0x02d8 /* Sector Erase */ 151#define BCMA_CC_FLASHCTL_ST_BE 0x00c7 /* Bulk Erase */ 152#define BCMA_CC_FLASHCTL_ST_DP 0x00b9 /* Deep Power-down */ 153#define BCMA_CC_FLASHCTL_ST_RES 0x03ab /* Read Electronic Signature */ 154#define BCMA_CC_FLASHCTL_ST_CSA 0x1000 /* Keep chip select asserted */ 155#define BCMA_CC_FLASHCTL_ST_SSE 0x0220 /* Sub-sector Erase */ 156/* Flashcontrol action + opcodes for Atmel flashes */ 157#define BCMA_CC_FLASHCTL_AT_READ 0x07e8 158#define BCMA_CC_FLASHCTL_AT_PAGE_READ 0x07d2 159#define BCMA_CC_FLASHCTL_AT_STATUS 0x01d7 160#define BCMA_CC_FLASHCTL_AT_BUF1_WRITE 0x0384 161#define BCMA_CC_FLASHCTL_AT_BUF2_WRITE 0x0387 162#define BCMA_CC_FLASHCTL_AT_BUF1_ERASE_PROGRAM 0x0283 163#define BCMA_CC_FLASHCTL_AT_BUF2_ERASE_PROGRAM 0x0286 164#define BCMA_CC_FLASHCTL_AT_BUF1_PROGRAM 0x0288 165#define BCMA_CC_FLASHCTL_AT_BUF2_PROGRAM 0x0289 166#define BCMA_CC_FLASHCTL_AT_PAGE_ERASE 0x0281 167#define BCMA_CC_FLASHCTL_AT_BLOCK_ERASE 0x0250 168#define BCMA_CC_FLASHCTL_AT_BUF1_WRITE_ERASE_PROGRAM 0x0382 169#define BCMA_CC_FLASHCTL_AT_BUF2_WRITE_ERASE_PROGRAM 0x0385 170#define BCMA_CC_FLASHCTL_AT_BUF1_LOAD 0x0253 171#define BCMA_CC_FLASHCTL_AT_BUF2_LOAD 0x0255 172#define BCMA_CC_FLASHCTL_AT_BUF1_COMPARE 0x0260 173#define BCMA_CC_FLASHCTL_AT_BUF2_COMPARE 0x0261 174#define BCMA_CC_FLASHCTL_AT_BUF1_REPROGRAM 0x0258 175#define BCMA_CC_FLASHCTL_AT_BUF2_REPROGRAM 0x0259 176#define BCMA_CC_FLASHADDR 0x0044 177#define BCMA_CC_FLASHDATA 0x0048 178/* Status register bits for ST flashes */ 179#define BCMA_CC_FLASHDATA_ST_WIP 0x01 /* Write In Progress */ 180#define BCMA_CC_FLASHDATA_ST_WEL 0x02 /* Write Enable Latch */ 181#define BCMA_CC_FLASHDATA_ST_BP_MASK 0x1c /* Block Protect */ 182#define BCMA_CC_FLASHDATA_ST_BP_SHIFT 2 183#define BCMA_CC_FLASHDATA_ST_SRWD 0x80 /* Status Register Write Disable */ 184/* Status register bits for Atmel flashes */ 185#define BCMA_CC_FLASHDATA_AT_READY 0x80 186#define BCMA_CC_FLASHDATA_AT_MISMATCH 0x40 187#define BCMA_CC_FLASHDATA_AT_ID_MASK 0x38 188#define BCMA_CC_FLASHDATA_AT_ID_SHIFT 3 189#define BCMA_CC_BCAST_ADDR 0x0050 190#define BCMA_CC_BCAST_DATA 0x0054 191#define BCMA_CC_GPIOPULLUP 0x0058 /* Rev >= 20 only */ 192#define BCMA_CC_GPIOPULLDOWN 0x005C /* Rev >= 20 only */ 193#define BCMA_CC_GPIOIN 0x0060 194#define BCMA_CC_GPIOOUT 0x0064 195#define BCMA_CC_GPIOOUTEN 0x0068 196#define BCMA_CC_GPIOCTL 0x006C 197#define BCMA_CC_GPIOPOL 0x0070 198#define BCMA_CC_GPIOIRQ 0x0074 199#define BCMA_CC_WATCHDOG 0x0080 200#define BCMA_CC_GPIOTIMER 0x0088 /* LED powersave (corerev >= 16) */ 201#define BCMA_CC_GPIOTIMER_OFFTIME 0x0000FFFF 202#define BCMA_CC_GPIOTIMER_OFFTIME_SHIFT 0 203#define BCMA_CC_GPIOTIMER_ONTIME 0xFFFF0000 204#define BCMA_CC_GPIOTIMER_ONTIME_SHIFT 16 205#define BCMA_CC_GPIOTOUTM 0x008C /* LED powersave (corerev >= 16) */ 206#define BCMA_CC_CLOCK_N 0x0090 207#define BCMA_CC_CLOCK_SB 0x0094 208#define BCMA_CC_CLOCK_PCI 0x0098 209#define BCMA_CC_CLOCK_M2 0x009C 210#define BCMA_CC_CLOCK_MIPS 0x00A0 211#define BCMA_CC_CLKDIV 0x00A4 /* Rev >= 3 only */ 212#define BCMA_CC_CLKDIV_SFLASH 0x0F000000 213#define BCMA_CC_CLKDIV_SFLASH_SHIFT 24 214#define BCMA_CC_CLKDIV_OTP 0x000F0000 215#define BCMA_CC_CLKDIV_OTP_SHIFT 16 216#define BCMA_CC_CLKDIV_JTAG 0x00000F00 217#define BCMA_CC_CLKDIV_JTAG_SHIFT 8 218#define BCMA_CC_CLKDIV_UART 0x000000FF 219#define BCMA_CC_CAP_EXT 0x00AC /* Capabilities */ 220#define BCMA_CC_PLLONDELAY 0x00B0 /* Rev >= 4 only */ 221#define BCMA_CC_FREFSELDELAY 0x00B4 /* Rev >= 4 only */ 222#define BCMA_CC_SLOWCLKCTL 0x00B8 /* 6 <= Rev <= 9 only */ 223#define BCMA_CC_SLOWCLKCTL_SRC 0x00000007 /* slow clock source mask */ 224#define BCMA_CC_SLOWCLKCTL_SRC_LPO 0x00000000 /* source of slow clock is LPO */ 225#define BCMA_CC_SLOWCLKCTL_SRC_XTAL 0x00000001 /* source of slow clock is crystal */ 226#define BCMA_CC_SLOECLKCTL_SRC_PCI 0x00000002 /* source of slow clock is PCI */ 227#define BCMA_CC_SLOWCLKCTL_LPOFREQ 0x00000200 /* LPOFreqSel, 1: 160Khz, 0: 32KHz */ 228#define BCMA_CC_SLOWCLKCTL_LPOPD 0x00000400 /* LPOPowerDown, 1: LPO is disabled, 0: LPO is enabled */ 229#define BCMA_CC_SLOWCLKCTL_FSLOW 0x00000800 /* ForceSlowClk, 1: sb/cores running on slow clock, 0: power logic control */ 230#define BCMA_CC_SLOWCLKCTL_IPLL 0x00001000 /* IgnorePllOffReq, 1/0: power logic ignores/honors PLL clock disable requests from core */ 231#define BCMA_CC_SLOWCLKCTL_ENXTAL 0x00002000 /* XtalControlEn, 1/0: power logic does/doesn't disable crystal when appropriate */ 232#define BCMA_CC_SLOWCLKCTL_XTALPU 0x00004000 /* XtalPU (RO), 1/0: crystal running/disabled */ 233#define BCMA_CC_SLOWCLKCTL_CLKDIV 0xFFFF0000 /* ClockDivider (SlowClk = 1/(4+divisor)) */ 234#define BCMA_CC_SLOWCLKCTL_CLKDIV_SHIFT 16 235#define BCMA_CC_SYSCLKCTL 0x00C0 /* Rev >= 3 only */ 236#define BCMA_CC_SYSCLKCTL_IDLPEN 0x00000001 /* ILPen: Enable Idle Low Power */ 237#define BCMA_CC_SYSCLKCTL_ALPEN 0x00000002 /* ALPen: Enable Active Low Power */ 238#define BCMA_CC_SYSCLKCTL_PLLEN 0x00000004 /* ForcePLLOn */ 239#define BCMA_CC_SYSCLKCTL_FORCEALP 0x00000008 /* Force ALP (or HT if ALPen is not set */ 240#define BCMA_CC_SYSCLKCTL_FORCEHT 0x00000010 /* Force HT */ 241#define BCMA_CC_SYSCLKCTL_CLKDIV 0xFFFF0000 /* ClkDiv (ILP = 1/(4+divisor)) */ 242#define BCMA_CC_SYSCLKCTL_CLKDIV_SHIFT 16 243#define BCMA_CC_CLKSTSTR 0x00C4 /* Rev >= 3 only */ 244#define BCMA_CC_EROM 0x00FC 245#define BCMA_CC_PCMCIA_CFG 0x0100 246#define BCMA_CC_PCMCIA_MEMWAIT 0x0104 247#define BCMA_CC_PCMCIA_ATTRWAIT 0x0108 248#define BCMA_CC_PCMCIA_IOWAIT 0x010C 249#define BCMA_CC_IDE_CFG 0x0110 250#define BCMA_CC_IDE_MEMWAIT 0x0114 251#define BCMA_CC_IDE_ATTRWAIT 0x0118 252#define BCMA_CC_IDE_IOWAIT 0x011C 253#define BCMA_CC_PROG_CFG 0x0120 254#define BCMA_CC_PROG_WAITCNT 0x0124 255#define BCMA_CC_FLASH_CFG 0x0128 256#define BCMA_CC_FLASH_CFG_DS 0x0010 /* Data size, 0=8bit, 1=16bit */ 257#define BCMA_CC_FLASH_WAITCNT 0x012C 258#define BCMA_CC_SROM_CONTROL 0x0190 259#define BCMA_CC_SROM_CONTROL_START 0x80000000 260#define BCMA_CC_SROM_CONTROL_BUSY 0x80000000 261#define BCMA_CC_SROM_CONTROL_OPCODE 0x60000000 262#define BCMA_CC_SROM_CONTROL_OP_READ 0x00000000 263#define BCMA_CC_SROM_CONTROL_OP_WRITE 0x20000000 264#define BCMA_CC_SROM_CONTROL_OP_WRDIS 0x40000000 265#define BCMA_CC_SROM_CONTROL_OP_WREN 0x60000000 266#define BCMA_CC_SROM_CONTROL_OTPSEL 0x00000010 267#define BCMA_CC_SROM_CONTROL_LOCK 0x00000008 268#define BCMA_CC_SROM_CONTROL_SIZE_MASK 0x00000006 269#define BCMA_CC_SROM_CONTROL_SIZE_1K 0x00000000 270#define BCMA_CC_SROM_CONTROL_SIZE_4K 0x00000002 271#define BCMA_CC_SROM_CONTROL_SIZE_16K 0x00000004 272#define BCMA_CC_SROM_CONTROL_SIZE_SHIFT 1 273#define BCMA_CC_SROM_CONTROL_PRESENT 0x00000001 274/* Block 0x140 - 0x190 registers are chipset specific */ 275#define BCMA_CC_4706_FLASHSCFG 0x18C /* Flash struct configuration */ 276#define BCMA_CC_4706_FLASHSCFG_MASK 0x000000ff 277#define BCMA_CC_4706_FLASHSCFG_SF1 0x00000001 /* 2nd serial flash present */ 278#define BCMA_CC_4706_FLASHSCFG_PF1 0x00000002 /* 2nd parallel flash present */ 279#define BCMA_CC_4706_FLASHSCFG_SF1_TYPE 0x00000004 /* 2nd serial flash type : 0 : ST, 1 : Atmel */ 280#define BCMA_CC_4706_FLASHSCFG_NF1 0x00000008 /* 2nd NAND flash present */ 281#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_MASK 0x000000f0 282#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_4MB 0x00000010 /* 4MB */ 283#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_8MB 0x00000020 /* 8MB */ 284#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_16MB 0x00000030 /* 16MB */ 285#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_32MB 0x00000040 /* 32MB */ 286#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_64MB 0x00000050 /* 64MB */ 287#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_128MB 0x00000060 /* 128MB */ 288#define BCMA_CC_4706_FLASHSCFG_1ST_MADDR_SEG_256MB 0x00000070 /* 256MB */ 289/* NAND flash registers for BCM4706 (corerev = 31) */ 290#define BCMA_CC_NFLASH_CTL 0x01A0 291#define BCMA_CC_NFLASH_CTL_ERR 0x08000000 292#define BCMA_CC_NFLASH_CONF 0x01A4 293#define BCMA_CC_NFLASH_COL_ADDR 0x01A8 294#define BCMA_CC_NFLASH_ROW_ADDR 0x01AC 295#define BCMA_CC_NFLASH_DATA 0x01B0 296#define BCMA_CC_NFLASH_WAITCNT0 0x01B4 297/* 0x1E0 is defined as shared BCMA_CLKCTLST */ 298#define BCMA_CC_HW_WORKAROUND 0x01E4 /* Hardware workaround (rev >= 20) */ 299#define BCMA_CC_UART0_DATA 0x0300 300#define BCMA_CC_UART0_IMR 0x0304 301#define BCMA_CC_UART0_FCR 0x0308 302#define BCMA_CC_UART0_LCR 0x030C 303#define BCMA_CC_UART0_MCR 0x0310 304#define BCMA_CC_UART0_LSR 0x0314 305#define BCMA_CC_UART0_MSR 0x0318 306#define BCMA_CC_UART0_SCRATCH 0x031C 307#define BCMA_CC_UART1_DATA 0x0400 308#define BCMA_CC_UART1_IMR 0x0404 309#define BCMA_CC_UART1_FCR 0x0408 310#define BCMA_CC_UART1_LCR 0x040C 311#define BCMA_CC_UART1_MCR 0x0410 312#define BCMA_CC_UART1_LSR 0x0414 313#define BCMA_CC_UART1_MSR 0x0418 314#define BCMA_CC_UART1_SCRATCH 0x041C 315/* PMU registers (rev >= 20) */ 316#define BCMA_CC_PMU_CTL 0x0600 /* PMU control */ 317#define BCMA_CC_PMU_CTL_ILP_DIV 0xFFFF0000 /* ILP div mask */ 318#define BCMA_CC_PMU_CTL_ILP_DIV_SHIFT 16 319#define BCMA_CC_PMU_CTL_RES 0x00006000 /* reset control mask */ 320#define BCMA_CC_PMU_CTL_RES_SHIFT 13 321#define BCMA_CC_PMU_CTL_RES_RELOAD 0x2 /* reload POR values */ 322#define BCMA_CC_PMU_CTL_PLL_UPD 0x00000400 323#define BCMA_CC_PMU_CTL_NOILPONW 0x00000200 /* No ILP on wait */ 324#define BCMA_CC_PMU_CTL_HTREQEN 0x00000100 /* HT req enable */ 325#define BCMA_CC_PMU_CTL_ALPREQEN 0x00000080 /* ALP req enable */ 326#define BCMA_CC_PMU_CTL_XTALFREQ 0x0000007C /* Crystal freq */ 327#define BCMA_CC_PMU_CTL_XTALFREQ_SHIFT 2 328#define BCMA_CC_PMU_CTL_ILPDIVEN 0x00000002 /* ILP div enable */ 329#define BCMA_CC_PMU_CTL_LPOSEL 0x00000001 /* LPO sel */ 330#define BCMA_CC_PMU_CAP 0x0604 /* PMU capabilities */ 331#define BCMA_CC_PMU_CAP_REVISION 0x000000FF /* Revision mask */ 332#define BCMA_CC_PMU_STAT 0x0608 /* PMU status */ 333#define BCMA_CC_PMU_STAT_EXT_LPO_AVAIL 0x00000100 334#define BCMA_CC_PMU_STAT_WDRESET 0x00000080 335#define BCMA_CC_PMU_STAT_INTPEND 0x00000040 /* Interrupt pending */ 336#define BCMA_CC_PMU_STAT_SBCLKST 0x00000030 /* Backplane clock status? */ 337#define BCMA_CC_PMU_STAT_HAVEALP 0x00000008 /* ALP available */ 338#define BCMA_CC_PMU_STAT_HAVEHT 0x00000004 /* HT available */ 339#define BCMA_CC_PMU_STAT_RESINIT 0x00000003 /* Res init */ 340#define BCMA_CC_PMU_RES_STAT 0x060C /* PMU res status */ 341#define BCMA_CC_PMU_RES_PEND 0x0610 /* PMU res pending */ 342#define BCMA_CC_PMU_TIMER 0x0614 /* PMU timer */ 343#define BCMA_CC_PMU_MINRES_MSK 0x0618 /* PMU min res mask */ 344#define BCMA_CC_PMU_MAXRES_MSK 0x061C /* PMU max res mask */ 345#define BCMA_CC_PMU_RES_TABSEL 0x0620 /* PMU res table sel */ 346#define BCMA_CC_PMU_RES_DEPMSK 0x0624 /* PMU res dep mask */ 347#define BCMA_CC_PMU_RES_UPDNTM 0x0628 /* PMU res updown timer */ 348#define BCMA_CC_PMU_RES_TIMER 0x062C /* PMU res timer */ 349#define BCMA_CC_PMU_CLKSTRETCH 0x0630 /* PMU clockstretch */ 350#define BCMA_CC_PMU_WATCHDOG 0x0634 /* PMU watchdog */ 351#define BCMA_CC_PMU_RES_REQTS 0x0640 /* PMU res req timer sel */ 352#define BCMA_CC_PMU_RES_REQT 0x0644 /* PMU res req timer */ 353#define BCMA_CC_PMU_RES_REQM 0x0648 /* PMU res req mask */ 354#define BCMA_CC_CHIPCTL_ADDR 0x0650 355#define BCMA_CC_CHIPCTL_DATA 0x0654 356#define BCMA_CC_REGCTL_ADDR 0x0658 357#define BCMA_CC_REGCTL_DATA 0x065C 358#define BCMA_CC_PLLCTL_ADDR 0x0660 359#define BCMA_CC_PLLCTL_DATA 0x0664 360#define BCMA_CC_PMU_STRAPOPT 0x0668 /* (corerev >= 28) */ 361#define BCMA_CC_PMU_XTAL_FREQ 0x066C /* (pmurev >= 10) */ 362#define BCMA_CC_PMU_XTAL_FREQ_ILPCTL_MASK 0x00001FFF 363#define BCMA_CC_PMU_XTAL_FREQ_MEASURE_MASK 0x80000000 364#define BCMA_CC_PMU_XTAL_FREQ_MEASURE_SHIFT 31 365#define BCMA_CC_SPROM 0x0800 /* SPROM beginning */ 366/* NAND flash MLC controller registers (corerev >= 38) */ 367#define BCMA_CC_NAND_REVISION 0x0C00 368#define BCMA_CC_NAND_CMD_START 0x0C04 369#define BCMA_CC_NAND_CMD_ADDR_X 0x0C08 370#define BCMA_CC_NAND_CMD_ADDR 0x0C0C 371#define BCMA_CC_NAND_CMD_END_ADDR 0x0C10 372#define BCMA_CC_NAND_CS_NAND_SELECT 0x0C14 373#define BCMA_CC_NAND_CS_NAND_XOR 0x0C18 374#define BCMA_CC_NAND_SPARE_RD0 0x0C20 375#define BCMA_CC_NAND_SPARE_RD4 0x0C24 376#define BCMA_CC_NAND_SPARE_RD8 0x0C28 377#define BCMA_CC_NAND_SPARE_RD12 0x0C2C 378#define BCMA_CC_NAND_SPARE_WR0 0x0C30 379#define BCMA_CC_NAND_SPARE_WR4 0x0C34 380#define BCMA_CC_NAND_SPARE_WR8 0x0C38 381#define BCMA_CC_NAND_SPARE_WR12 0x0C3C 382#define BCMA_CC_NAND_ACC_CONTROL 0x0C40 383#define BCMA_CC_NAND_CONFIG 0x0C48 384#define BCMA_CC_NAND_TIMING_1 0x0C50 385#define BCMA_CC_NAND_TIMING_2 0x0C54 386#define BCMA_CC_NAND_SEMAPHORE 0x0C58 387#define BCMA_CC_NAND_DEVID 0x0C60 388#define BCMA_CC_NAND_DEVID_X 0x0C64 389#define BCMA_CC_NAND_BLOCK_LOCK_STATUS 0x0C68 390#define BCMA_CC_NAND_INTFC_STATUS 0x0C6C 391#define BCMA_CC_NAND_ECC_CORR_ADDR_X 0x0C70 392#define BCMA_CC_NAND_ECC_CORR_ADDR 0x0C74 393#define BCMA_CC_NAND_ECC_UNC_ADDR_X 0x0C78 394#define BCMA_CC_NAND_ECC_UNC_ADDR 0x0C7C 395#define BCMA_CC_NAND_READ_ERROR_COUNT 0x0C80 396#define BCMA_CC_NAND_CORR_STAT_THRESHOLD 0x0C84 397#define BCMA_CC_NAND_READ_ADDR_X 0x0C90 398#define BCMA_CC_NAND_READ_ADDR 0x0C94 399#define BCMA_CC_NAND_PAGE_PROGRAM_ADDR_X 0x0C98 400#define BCMA_CC_NAND_PAGE_PROGRAM_ADDR 0x0C9C 401#define BCMA_CC_NAND_COPY_BACK_ADDR_X 0x0CA0 402#define BCMA_CC_NAND_COPY_BACK_ADDR 0x0CA4 403#define BCMA_CC_NAND_BLOCK_ERASE_ADDR_X 0x0CA8 404#define BCMA_CC_NAND_BLOCK_ERASE_ADDR 0x0CAC 405#define BCMA_CC_NAND_INV_READ_ADDR_X 0x0CB0 406#define BCMA_CC_NAND_INV_READ_ADDR 0x0CB4 407#define BCMA_CC_NAND_BLK_WR_PROTECT 0x0CC0 408#define BCMA_CC_NAND_ACC_CONTROL_CS1 0x0CD0 409#define BCMA_CC_NAND_CONFIG_CS1 0x0CD4 410#define BCMA_CC_NAND_TIMING_1_CS1 0x0CD8 411#define BCMA_CC_NAND_TIMING_2_CS1 0x0CDC 412#define BCMA_CC_NAND_SPARE_RD16 0x0D30 413#define BCMA_CC_NAND_SPARE_RD20 0x0D34 414#define BCMA_CC_NAND_SPARE_RD24 0x0D38 415#define BCMA_CC_NAND_SPARE_RD28 0x0D3C 416#define BCMA_CC_NAND_CACHE_ADDR 0x0D40 417#define BCMA_CC_NAND_CACHE_DATA 0x0D44 418#define BCMA_CC_NAND_CTRL_CONFIG 0x0D48 419#define BCMA_CC_NAND_CTRL_STATUS 0x0D4C 420 421/* Divider allocation in 4716/47162/5356 */ 422#define BCMA_CC_PMU5_MAINPLL_CPU 1 423#define BCMA_CC_PMU5_MAINPLL_MEM 2 424#define BCMA_CC_PMU5_MAINPLL_SSB 3 425 426/* PLL usage in 4716/47162 */ 427#define BCMA_CC_PMU4716_MAINPLL_PLL0 12 428 429/* PLL usage in 5356/5357 */ 430#define BCMA_CC_PMU5356_MAINPLL_PLL0 0 431#define BCMA_CC_PMU5357_MAINPLL_PLL0 0 432 433/* 4706 PMU */ 434#define BCMA_CC_PMU4706_MAINPLL_PLL0 0 435#define BCMA_CC_PMU6_4706_PROCPLL_OFF 4 /* The CPU PLL */ 436#define BCMA_CC_PMU6_4706_PROC_P2DIV_MASK 0x000f0000 437#define BCMA_CC_PMU6_4706_PROC_P2DIV_SHIFT 16 438#define BCMA_CC_PMU6_4706_PROC_P1DIV_MASK 0x0000f000 439#define BCMA_CC_PMU6_4706_PROC_P1DIV_SHIFT 12 440#define BCMA_CC_PMU6_4706_PROC_NDIV_INT_MASK 0x00000ff8 441#define BCMA_CC_PMU6_4706_PROC_NDIV_INT_SHIFT 3 442#define BCMA_CC_PMU6_4706_PROC_NDIV_MODE_MASK 0x00000007 443#define BCMA_CC_PMU6_4706_PROC_NDIV_MODE_SHIFT 0 444 445/* PMU rev 15 */ 446#define BCMA_CC_PMU15_PLL_PLLCTL0 0 447#define BCMA_CC_PMU15_PLL_PC0_CLKSEL_MASK 0x00000003 448#define BCMA_CC_PMU15_PLL_PC0_CLKSEL_SHIFT 0 449#define BCMA_CC_PMU15_PLL_PC0_FREQTGT_MASK 0x003FFFFC 450#define BCMA_CC_PMU15_PLL_PC0_FREQTGT_SHIFT 2 451#define BCMA_CC_PMU15_PLL_PC0_PRESCALE_MASK 0x00C00000 452#define BCMA_CC_PMU15_PLL_PC0_PRESCALE_SHIFT 22 453#define BCMA_CC_PMU15_PLL_PC0_KPCTRL_MASK 0x07000000 454#define BCMA_CC_PMU15_PLL_PC0_KPCTRL_SHIFT 24 455#define BCMA_CC_PMU15_PLL_PC0_FCNTCTRL_MASK 0x38000000 456#define BCMA_CC_PMU15_PLL_PC0_FCNTCTRL_SHIFT 27 457#define BCMA_CC_PMU15_PLL_PC0_FDCMODE_MASK 0x40000000 458#define BCMA_CC_PMU15_PLL_PC0_FDCMODE_SHIFT 30 459#define BCMA_CC_PMU15_PLL_PC0_CTRLBIAS_MASK 0x80000000 460#define BCMA_CC_PMU15_PLL_PC0_CTRLBIAS_SHIFT 31 461 462/* ALP clock on pre-PMU chips */ 463#define BCMA_CC_PMU_ALP_CLOCK 20000000 464/* HT clock for systems with PMU-enabled chipcommon */ 465#define BCMA_CC_PMU_HT_CLOCK 80000000 466 467/* PMU rev 5 (& 6) */ 468#define BCMA_CC_PPL_P1P2_OFF 0 469#define BCMA_CC_PPL_P1_MASK 0x0f000000 470#define BCMA_CC_PPL_P1_SHIFT 24 471#define BCMA_CC_PPL_P2_MASK 0x00f00000 472#define BCMA_CC_PPL_P2_SHIFT 20 473#define BCMA_CC_PPL_M14_OFF 1 474#define BCMA_CC_PPL_MDIV_MASK 0x000000ff 475#define BCMA_CC_PPL_MDIV_WIDTH 8 476#define BCMA_CC_PPL_NM5_OFF 2 477#define BCMA_CC_PPL_NDIV_MASK 0xfff00000 478#define BCMA_CC_PPL_NDIV_SHIFT 20 479#define BCMA_CC_PPL_FMAB_OFF 3 480#define BCMA_CC_PPL_MRAT_MASK 0xf0000000 481#define BCMA_CC_PPL_MRAT_SHIFT 28 482#define BCMA_CC_PPL_ABRAT_MASK 0x08000000 483#define BCMA_CC_PPL_ABRAT_SHIFT 27 484#define BCMA_CC_PPL_FDIV_MASK 0x07ffffff 485#define BCMA_CC_PPL_PLLCTL_OFF 4 486#define BCMA_CC_PPL_PCHI_OFF 5 487#define BCMA_CC_PPL_PCHI_MASK 0x0000003f 488 489#define BCMA_CC_PMU_PLL_CTL0 0 490#define BCMA_CC_PMU_PLL_CTL1 1 491#define BCMA_CC_PMU_PLL_CTL2 2 492#define BCMA_CC_PMU_PLL_CTL3 3 493#define BCMA_CC_PMU_PLL_CTL4 4 494#define BCMA_CC_PMU_PLL_CTL5 5 495 496#define BCMA_CC_PMU1_PLL0_PC0_P1DIV_MASK 0x00f00000 497#define BCMA_CC_PMU1_PLL0_PC0_P1DIV_SHIFT 20 498 499#define BCMA_CC_PMU1_PLL0_PC2_NDIV_INT_MASK 0x1ff00000 500#define BCMA_CC_PMU1_PLL0_PC2_NDIV_INT_SHIFT 20 501 502/* BCM4331 ChipControl numbers. */ 503#define BCMA_CHIPCTL_4331_BT_COEXIST BIT(0) /* 0 disable */ 504#define BCMA_CHIPCTL_4331_SECI BIT(1) /* 0 SECI is disabled (JATG functional) */ 505#define BCMA_CHIPCTL_4331_EXT_LNA BIT(2) /* 0 disable */ 506#define BCMA_CHIPCTL_4331_SPROM_GPIO13_15 BIT(3) /* sprom/gpio13-15 mux */ 507#define BCMA_CHIPCTL_4331_EXTPA_EN BIT(4) /* 0 ext pa disable, 1 ext pa enabled */ 508#define BCMA_CHIPCTL_4331_GPIOCLK_ON_SPROMCS BIT(5) /* set drive out GPIO_CLK on sprom_cs pin */ 509#define BCMA_CHIPCTL_4331_PCIE_MDIO_ON_SPROMCS BIT(6) /* use sprom_cs pin as PCIE mdio interface */ 510#define BCMA_CHIPCTL_4331_EXTPA_ON_GPIO2_5 BIT(7) /* aband extpa will be at gpio2/5 and sprom_dout */ 511#define BCMA_CHIPCTL_4331_OVR_PIPEAUXCLKEN BIT(8) /* override core control on pipe_AuxClkEnable */ 512#define BCMA_CHIPCTL_4331_OVR_PIPEAUXPWRDOWN BIT(9) /* override core control on pipe_AuxPowerDown */ 513#define BCMA_CHIPCTL_4331_PCIE_AUXCLKEN BIT(10) /* pcie_auxclkenable */ 514#define BCMA_CHIPCTL_4331_PCIE_PIPE_PLLDOWN BIT(11) /* pcie_pipe_pllpowerdown */ 515#define BCMA_CHIPCTL_4331_EXTPA_EN2 BIT(12) /* 0 ext pa disable, 1 ext pa enabled */ 516#define BCMA_CHIPCTL_4331_BT_SHD0_ON_GPIO4 BIT(16) /* enable bt_shd0 at gpio4 */ 517#define BCMA_CHIPCTL_4331_BT_SHD1_ON_GPIO5 BIT(17) /* enable bt_shd1 at gpio5 */ 518 519/* 43224 chip-specific ChipControl register bits */ 520#define BCMA_CCTRL_43224_GPIO_TOGGLE 0x8000 /* gpio[3:0] pins as btcoex or s/w gpio */ 521#define BCMA_CCTRL_43224A0_12MA_LED_DRIVE 0x00F000F0 /* 12 mA drive strength */ 522#define BCMA_CCTRL_43224B0_12MA_LED_DRIVE 0xF0 /* 12 mA drive strength for later 43224s */ 523 524/* 4313 Chip specific ChipControl register bits */ 525#define BCMA_CCTRL_4313_12MA_LED_DRIVE 0x00000007 /* 12 mA drive strengh for later 4313 */ 526 527/* BCM5357 ChipControl register bits */ 528#define BCMA_CHIPCTL_5357_EXTPA BIT(14) 529#define BCMA_CHIPCTL_5357_ANT_MUX_2O3 BIT(15) 530#define BCMA_CHIPCTL_5357_NFLASH BIT(16) 531#define BCMA_CHIPCTL_5357_I2S_PINS_ENABLE BIT(18) 532#define BCMA_CHIPCTL_5357_I2CSPI_PINS_ENABLE BIT(19) 533 534#define BCMA_RES_4314_LPLDO_PU BIT(0) 535#define BCMA_RES_4314_PMU_SLEEP_DIS BIT(1) 536#define BCMA_RES_4314_PMU_BG_PU BIT(2) 537#define BCMA_RES_4314_CBUCK_LPOM_PU BIT(3) 538#define BCMA_RES_4314_CBUCK_PFM_PU BIT(4) 539#define BCMA_RES_4314_CLDO_PU BIT(5) 540#define BCMA_RES_4314_LPLDO2_LVM BIT(6) 541#define BCMA_RES_4314_WL_PMU_PU BIT(7) 542#define BCMA_RES_4314_LNLDO_PU BIT(8) 543#define BCMA_RES_4314_LDO3P3_PU BIT(9) 544#define BCMA_RES_4314_OTP_PU BIT(10) 545#define BCMA_RES_4314_XTAL_PU BIT(11) 546#define BCMA_RES_4314_WL_PWRSW_PU BIT(12) 547#define BCMA_RES_4314_LQ_AVAIL BIT(13) 548#define BCMA_RES_4314_LOGIC_RET BIT(14) 549#define BCMA_RES_4314_MEM_SLEEP BIT(15) 550#define BCMA_RES_4314_MACPHY_RET BIT(16) 551#define BCMA_RES_4314_WL_CORE_READY BIT(17) 552#define BCMA_RES_4314_ILP_REQ BIT(18) 553#define BCMA_RES_4314_ALP_AVAIL BIT(19) 554#define BCMA_RES_4314_MISC_PWRSW_PU BIT(20) 555#define BCMA_RES_4314_SYNTH_PWRSW_PU BIT(21) 556#define BCMA_RES_4314_RX_PWRSW_PU BIT(22) 557#define BCMA_RES_4314_RADIO_PU BIT(23) 558#define BCMA_RES_4314_VCO_LDO_PU BIT(24) 559#define BCMA_RES_4314_AFE_LDO_PU BIT(25) 560#define BCMA_RES_4314_RX_LDO_PU BIT(26) 561#define BCMA_RES_4314_TX_LDO_PU BIT(27) 562#define BCMA_RES_4314_HT_AVAIL BIT(28) 563#define BCMA_RES_4314_MACPHY_CLK_AVAIL BIT(29) 564 565/* Data for the PMU, if available. 566 * Check availability with ((struct bcma_chipcommon)->capabilities & BCMA_CC_CAP_PMU) 567 */ 568struct bcma_chipcommon_pmu { 569 u8 rev; /* PMU revision */ 570 u32 crystalfreq; /* The active crystal frequency (in kHz) */ 571}; 572 573#ifdef CONFIG_BCMA_DRIVER_MIPS 574struct bcma_pflash { 575 bool present; 576 u8 buswidth; 577 u32 window; 578 u32 window_size; 579}; 580 581#ifdef CONFIG_BCMA_SFLASH 582struct bcma_sflash { 583 bool present; 584 u32 window; 585 u32 blocksize; 586 u16 numblocks; 587 u32 size; 588 589 struct mtd_info *mtd; 590 void *priv; 591}; 592#endif 593 594#ifdef CONFIG_BCMA_NFLASH 595struct mtd_info; 596 597struct bcma_nflash { 598 bool present; 599 bool boot; /* This is the flash the SoC boots from */ 600 601 struct mtd_info *mtd; 602}; 603#endif 604 605struct bcma_serial_port { 606 void *regs; 607 unsigned long clockspeed; 608 unsigned int irq; 609 unsigned int baud_base; 610 unsigned int reg_shift; 611}; 612#endif /* CONFIG_BCMA_DRIVER_MIPS */ 613 614struct bcma_drv_cc { 615 struct bcma_device *core; 616 u32 status; 617 u32 capabilities; 618 u32 capabilities_ext; 619 u8 setup_done:1; 620 u8 early_setup_done:1; 621 /* Fast Powerup Delay constant */ 622 u16 fast_pwrup_delay; 623 struct bcma_chipcommon_pmu pmu; 624#ifdef CONFIG_BCMA_DRIVER_MIPS 625 struct bcma_pflash pflash; 626#ifdef CONFIG_BCMA_SFLASH 627 struct bcma_sflash sflash; 628#endif 629#ifdef CONFIG_BCMA_NFLASH 630 struct bcma_nflash nflash; 631#endif 632 633 int nr_serial_ports; 634 struct bcma_serial_port serial_ports[4]; 635#endif /* CONFIG_BCMA_DRIVER_MIPS */ 636 u32 ticks_per_ms; 637 struct platform_device *watchdog; 638 639 /* Lock for GPIO register access. */ 640 spinlock_t gpio_lock; 641#ifdef CONFIG_BCMA_DRIVER_GPIO 642 struct gpio_chip gpio; 643 struct irq_domain *irq_domain; 644#endif 645}; 646 647struct bcma_drv_cc_b { 648 struct bcma_device *core; 649 u8 setup_done:1; 650 void __iomem *mii; 651}; 652 653/* Register access */ 654#define bcma_cc_read32(cc, offset) \ 655 bcma_read32((cc)->core, offset) 656#define bcma_cc_write32(cc, offset, val) \ 657 bcma_write32((cc)->core, offset, val) 658 659#define bcma_cc_mask32(cc, offset, mask) \ 660 bcma_cc_write32(cc, offset, bcma_cc_read32(cc, offset) & (mask)) 661#define bcma_cc_set32(cc, offset, set) \ 662 bcma_cc_write32(cc, offset, bcma_cc_read32(cc, offset) | (set)) 663#define bcma_cc_maskset32(cc, offset, mask, set) \ 664 bcma_cc_write32(cc, offset, (bcma_cc_read32(cc, offset) & (mask)) | (set)) 665 666extern u32 bcma_chipco_watchdog_timer_set(struct bcma_drv_cc *cc, u32 ticks); 667 668extern u32 bcma_chipco_get_alp_clock(struct bcma_drv_cc *cc); 669 670void bcma_chipco_irq_mask(struct bcma_drv_cc *cc, u32 mask, u32 value); 671 672u32 bcma_chipco_irq_status(struct bcma_drv_cc *cc, u32 mask); 673 674/* Chipcommon GPIO pin access. */ 675u32 bcma_chipco_gpio_in(struct bcma_drv_cc *cc, u32 mask); 676u32 bcma_chipco_gpio_out(struct bcma_drv_cc *cc, u32 mask, u32 value); 677u32 bcma_chipco_gpio_outen(struct bcma_drv_cc *cc, u32 mask, u32 value); 678u32 bcma_chipco_gpio_control(struct bcma_drv_cc *cc, u32 mask, u32 value); 679u32 bcma_chipco_gpio_intmask(struct bcma_drv_cc *cc, u32 mask, u32 value); 680u32 bcma_chipco_gpio_polarity(struct bcma_drv_cc *cc, u32 mask, u32 value); 681u32 bcma_chipco_gpio_pullup(struct bcma_drv_cc *cc, u32 mask, u32 value); 682u32 bcma_chipco_gpio_pulldown(struct bcma_drv_cc *cc, u32 mask, u32 value); 683 684/* PMU support */ 685extern void bcma_chipco_pll_write(struct bcma_drv_cc *cc, u32 offset, 686 u32 value); 687extern void bcma_chipco_pll_maskset(struct bcma_drv_cc *cc, u32 offset, 688 u32 mask, u32 set); 689extern void bcma_chipco_chipctl_maskset(struct bcma_drv_cc *cc, 690 u32 offset, u32 mask, u32 set); 691extern void bcma_chipco_regctl_maskset(struct bcma_drv_cc *cc, 692 u32 offset, u32 mask, u32 set); 693extern void bcma_pmu_spuravoid_pllupdate(struct bcma_drv_cc *cc, int spuravoid); 694 695extern u32 bcma_pmu_get_bus_clock(struct bcma_drv_cc *cc); 696 697void bcma_chipco_b_mii_write(struct bcma_drv_cc_b *ccb, u32 offset, u32 value); 698 699#endif /* LINUX_BCMA_DRIVER_CC_H_ */ 700