drivers/gpio/gpio-winbond.c

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
winbond_sio_enter
winbond_sio_select_logical
winbond_sio_leave
winbond_sio_reg_write
winbond_sio_reg_read
winbond_sio_reg_bset
winbond_sio_reg_bclear
winbond_sio_reg_btest
winbond_gpio_get_info
winbond_gpio_get
winbond_gpio_direction_in
winbond_gpio_direction_out
winbond_gpio_set
winbond_gpio_configure_port0_pins
winbond_gpio_configure_port1_check_i2c
winbond_gpio_configure_port
winbond_gpio_configure
winbond_gpio_check_chip
winbond_gpio_imatch
winbond_gpio_iprobe
   1 // SPDX-License-Identifier: GPL-2.0+
   2 /*
   3  * GPIO interface for Winbond Super I/O chips
   4  * Currently, only W83627UHG (Nuvoton NCT6627UD) is supported.
   5  *
   6  * Author: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
   7  */
   8 
   9 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
  10 
  11 #include <linux/gpio/driver.h>
  12 #include <linux/ioport.h>
  13 #include <linux/isa.h>
  14 #include <linux/module.h>
  15 
  16 #define WB_GPIO_DRIVER_NAME             KBUILD_MODNAME
  17 
  18 #define WB_SIO_BASE                     0x2e
  19 #define WB_SIO_BASE_HIGH                0x4e
  20 
  21 #define WB_SIO_EXT_ENTER_KEY            0x87
  22 #define WB_SIO_EXT_EXIT_KEY             0xaa
  23 
  24 /* global chip registers */
  25 
  26 #define WB_SIO_REG_LOGICAL              0x07
  27 
  28 #define WB_SIO_REG_CHIP_MSB             0x20
  29 #define WB_SIO_REG_CHIP_LSB             0x21
  30 
  31 #define WB_SIO_CHIP_ID_W83627UHG        0xa230
  32 #define WB_SIO_CHIP_ID_W83627UHG_MASK   GENMASK(15, 4)
  33 
  34 #define WB_SIO_REG_DPD                  0x22
  35 #define WB_SIO_REG_DPD_UARTA            4
  36 #define WB_SIO_REG_DPD_UARTB            5
  37 
  38 #define WB_SIO_REG_IDPD         0x23
  39 #define WB_SIO_REG_IDPD_UARTC           4
  40 #define WB_SIO_REG_IDPD_UARTD           5
  41 #define WB_SIO_REG_IDPD_UARTE           6
  42 #define WB_SIO_REG_IDPD_UARTF           7
  43 
  44 #define WB_SIO_REG_GLOBAL_OPT           0x24
  45 #define WB_SIO_REG_GO_ENFDC             1
  46 
  47 #define WB_SIO_REG_OVTGPIO3456          0x29
  48 #define WB_SIO_REG_OG3456_G3PP          3
  49 #define WB_SIO_REG_OG3456_G4PP          4
  50 #define WB_SIO_REG_OG3456_G5PP          5
  51 #define WB_SIO_REG_OG3456_G6PP          7
  52 
  53 #define WB_SIO_REG_I2C_PS               0x2a
  54 #define WB_SIO_REG_I2CPS_I2CFS          1
  55 
  56 #define WB_SIO_REG_GPIO1_MF             0x2c
  57 #define WB_SIO_REG_G1MF_G1PP            6
  58 #define WB_SIO_REG_G1MF_G2PP            7
  59 #define WB_SIO_REG_G1MF_FS_MASK GENMASK(1, 0)
  60 #define WB_SIO_REG_G1MF_FS_IR_OFF       0
  61 #define WB_SIO_REG_G1MF_FS_IR           1
  62 #define WB_SIO_REG_G1MF_FS_GPIO1        2
  63 #define WB_SIO_REG_G1MF_FS_UARTB        3
  64 
  65 /* not an actual device number, just a value meaning 'no device' */
  66 #define WB_SIO_DEV_NONE         0xff
  67 
  68 /* registers with offsets >= 0x30 are specific for a particular device */
  69 
  70 /* UART B logical device */
  71 #define WB_SIO_DEV_UARTB                0x03
  72 #define WB_SIO_UARTB_REG_ENABLE 0x30
  73 #define WB_SIO_UARTB_ENABLE_ON          0
  74 
  75 /* UART C logical device */
  76 #define WB_SIO_DEV_UARTC                0x06
  77 #define WB_SIO_UARTC_REG_ENABLE 0x30
  78 #define WB_SIO_UARTC_ENABLE_ON          0
  79 
  80 /* GPIO3, GPIO4 logical device */
  81 #define WB_SIO_DEV_GPIO34               0x07
  82 #define WB_SIO_GPIO34_REG_ENABLE        0x30
  83 #define WB_SIO_GPIO34_ENABLE_3          0
  84 #define WB_SIO_GPIO34_ENABLE_4          1
  85 #define WB_SIO_GPIO34_REG_IO3           0xe0
  86 #define WB_SIO_GPIO34_REG_DATA3 0xe1
  87 #define WB_SIO_GPIO34_REG_INV3          0xe2
  88 #define WB_SIO_GPIO34_REG_IO4           0xe4
  89 #define WB_SIO_GPIO34_REG_DATA4 0xe5
  90 #define WB_SIO_GPIO34_REG_INV4          0xe6
  91 
  92 /* WDTO, PLED, GPIO5, GPIO6 logical device */
  93 #define WB_SIO_DEV_WDGPIO56             0x08
  94 #define WB_SIO_WDGPIO56_REG_ENABLE      0x30
  95 #define WB_SIO_WDGPIO56_ENABLE_5        1
  96 #define WB_SIO_WDGPIO56_ENABLE_6        2
  97 #define WB_SIO_WDGPIO56_REG_IO5 0xe0
  98 #define WB_SIO_WDGPIO56_REG_DATA5       0xe1
  99 #define WB_SIO_WDGPIO56_REG_INV5        0xe2
 100 #define WB_SIO_WDGPIO56_REG_IO6 0xe4
 101 #define WB_SIO_WDGPIO56_REG_DATA6       0xe5
 102 #define WB_SIO_WDGPIO56_REG_INV6        0xe6
 103 
 104 /* GPIO1, GPIO2, SUSLED logical device */
 105 #define WB_SIO_DEV_GPIO12               0x09
 106 #define WB_SIO_GPIO12_REG_ENABLE        0x30
 107 #define WB_SIO_GPIO12_ENABLE_1          0
 108 #define WB_SIO_GPIO12_ENABLE_2          1
 109 #define WB_SIO_GPIO12_REG_IO1           0xe0
 110 #define WB_SIO_GPIO12_REG_DATA1 0xe1
 111 #define WB_SIO_GPIO12_REG_INV1          0xe2
 112 #define WB_SIO_GPIO12_REG_IO2           0xe4
 113 #define WB_SIO_GPIO12_REG_DATA2 0xe5
 114 #define WB_SIO_GPIO12_REG_INV2          0xe6
 115 
 116 /* UART D logical device */
 117 #define WB_SIO_DEV_UARTD                0x0d
 118 #define WB_SIO_UARTD_REG_ENABLE 0x30
 119 #define WB_SIO_UARTD_ENABLE_ON          0
 120 
 121 /* UART E logical device */
 122 #define WB_SIO_DEV_UARTE                0x0e
 123 #define WB_SIO_UARTE_REG_ENABLE 0x30
 124 #define WB_SIO_UARTE_ENABLE_ON          0
 125 
 126 /*
 127  * for a description what a particular field of this struct means please see
 128  * a description of the relevant module parameter at the bottom of this file
 129  */
 130 struct winbond_gpio_params {
 131         unsigned long base;
 132         unsigned long gpios;
 133         unsigned long ppgpios;
 134         unsigned long odgpios;
 135         bool pledgpio;
 136         bool beepgpio;
 137         bool i2cgpio;
 138 };
 139 
 140 static struct winbond_gpio_params params;
 141 
 142 static int winbond_sio_enter(unsigned long base)
 143 {
 144         if (!request_muxed_region(base, 2, WB_GPIO_DRIVER_NAME))
 145                 return -EBUSY;
 146 
 147         /*
 148          * datasheet says two successive writes of the "key" value are needed
 149          * in order for chip to enter the "Extended Function Mode"
 150          */
 151         outb(WB_SIO_EXT_ENTER_KEY, base);
 152         outb(WB_SIO_EXT_ENTER_KEY, base);
 153 
 154         return 0;
 155 }
 156 
 157 static void winbond_sio_select_logical(unsigned long base, u8 dev)
 158 {
 159         outb(WB_SIO_REG_LOGICAL, base);
 160         outb(dev, base + 1);
 161 }
 162 
 163 static void winbond_sio_leave(unsigned long base)
 164 {
 165         outb(WB_SIO_EXT_EXIT_KEY, base);
 166 
 167         release_region(base, 2);
 168 }
 169 
 170 static void winbond_sio_reg_write(unsigned long base, u8 reg, u8 data)
 171 {
 172         outb(reg, base);
 173         outb(data, base + 1);
 174 }
 175 
 176 static u8 winbond_sio_reg_read(unsigned long base, u8 reg)
 177 {
 178         outb(reg, base);
 179         return inb(base + 1);
 180 }
 181 
 182 static void winbond_sio_reg_bset(unsigned long base, u8 reg, u8 bit)
 183 {
 184         u8 val;
 185 
 186         val = winbond_sio_reg_read(base, reg);
 187         val |= BIT(bit);
 188         winbond_sio_reg_write(base, reg, val);
 189 }
 190 
 191 static void winbond_sio_reg_bclear(unsigned long base, u8 reg, u8 bit)
 192 {
 193         u8 val;
 194 
 195         val = winbond_sio_reg_read(base, reg);
 196         val &= ~BIT(bit);
 197         winbond_sio_reg_write(base, reg, val);
 198 }
 199 
 200 static bool winbond_sio_reg_btest(unsigned long base, u8 reg, u8 bit)
 201 {
 202         return winbond_sio_reg_read(base, reg) & BIT(bit);
 203 }
 204 
 205 /**
 206  * struct winbond_gpio_port_conflict - possibly conflicting device information
 207  * @name:       device name (NULL means no conflicting device defined)
 208  * @dev:        Super I/O logical device number where the testreg register
 209  *              is located (or WB_SIO_DEV_NONE - don't select any
 210  *              logical device)
 211  * @testreg:    register number where the testbit bit is located
 212  * @testbit:    index of a bit to check whether an actual conflict exists
 213  * @warnonly:   if set then a conflict isn't fatal (just warn about it),
 214  *              otherwise disable the particular GPIO port if a conflict
 215  *              is detected
 216  */
 217 struct winbond_gpio_port_conflict {
 218         const char *name;
 219         u8 dev;
 220         u8 testreg;
 221         u8 testbit;
 222         bool warnonly;
 223 };
 224 
 225 /**
 226  * struct winbond_gpio_info - information about a particular GPIO port (device)
 227  * @dev:                Super I/O logical device number of the registers
 228  *                      specified below
 229  * @enablereg:          port enable bit register number
 230  * @enablebit:          index of a port enable bit
 231  * @outputreg:          output driver mode bit register number
 232  * @outputppbit:        index of a push-pull output driver mode bit
 233  * @ioreg:              data direction register number
 234  * @invreg:             pin data inversion register number
 235  * @datareg:            pin data register number
 236  * @conflict:           description of a device that possibly conflicts with
 237  *                      this port
 238  */
 239 struct winbond_gpio_info {
 240         u8 dev;
 241         u8 enablereg;
 242         u8 enablebit;
 243         u8 outputreg;
 244         u8 outputppbit;
 245         u8 ioreg;
 246         u8 invreg;
 247         u8 datareg;
 248         struct winbond_gpio_port_conflict conflict;
 249 };
 250 
 251 static const struct winbond_gpio_info winbond_gpio_infos[6] = {
 252         { /* 0 */
 253                 .dev = WB_SIO_DEV_GPIO12,
 254                 .enablereg = WB_SIO_GPIO12_REG_ENABLE,
 255                 .enablebit = WB_SIO_GPIO12_ENABLE_1,
 256                 .outputreg = WB_SIO_REG_GPIO1_MF,
 257                 .outputppbit = WB_SIO_REG_G1MF_G1PP,
 258                 .ioreg = WB_SIO_GPIO12_REG_IO1,
 259                 .invreg = WB_SIO_GPIO12_REG_INV1,
 260                 .datareg = WB_SIO_GPIO12_REG_DATA1,
 261                 .conflict = {
 262                         .name = "UARTB",
 263                         .dev = WB_SIO_DEV_UARTB,
 264                         .testreg = WB_SIO_UARTB_REG_ENABLE,
 265                         .testbit = WB_SIO_UARTB_ENABLE_ON,
 266                         .warnonly = true
 267                 }
 268         },
 269         { /* 1 */
 270                 .dev = WB_SIO_DEV_GPIO12,
 271                 .enablereg = WB_SIO_GPIO12_REG_ENABLE,
 272                 .enablebit = WB_SIO_GPIO12_ENABLE_2,
 273                 .outputreg = WB_SIO_REG_GPIO1_MF,
 274                 .outputppbit = WB_SIO_REG_G1MF_G2PP,
 275                 .ioreg = WB_SIO_GPIO12_REG_IO2,
 276                 .invreg = WB_SIO_GPIO12_REG_INV2,
 277                 .datareg = WB_SIO_GPIO12_REG_DATA2
 278                 /* special conflict handling so doesn't use conflict data */
 279         },
 280         { /* 2 */
 281                 .dev = WB_SIO_DEV_GPIO34,
 282                 .enablereg = WB_SIO_GPIO34_REG_ENABLE,
 283                 .enablebit = WB_SIO_GPIO34_ENABLE_3,
 284                 .outputreg = WB_SIO_REG_OVTGPIO3456,
 285                 .outputppbit = WB_SIO_REG_OG3456_G3PP,
 286                 .ioreg = WB_SIO_GPIO34_REG_IO3,
 287                 .invreg = WB_SIO_GPIO34_REG_INV3,
 288                 .datareg = WB_SIO_GPIO34_REG_DATA3,
 289                 .conflict = {
 290                         .name = "UARTC",
 291                         .dev = WB_SIO_DEV_UARTC,
 292                         .testreg = WB_SIO_UARTC_REG_ENABLE,
 293                         .testbit = WB_SIO_UARTC_ENABLE_ON,
 294                         .warnonly = true
 295                 }
 296         },
 297         { /* 3 */
 298                 .dev = WB_SIO_DEV_GPIO34,
 299                 .enablereg = WB_SIO_GPIO34_REG_ENABLE,
 300                 .enablebit = WB_SIO_GPIO34_ENABLE_4,
 301                 .outputreg = WB_SIO_REG_OVTGPIO3456,
 302                 .outputppbit = WB_SIO_REG_OG3456_G4PP,
 303                 .ioreg = WB_SIO_GPIO34_REG_IO4,
 304                 .invreg = WB_SIO_GPIO34_REG_INV4,
 305                 .datareg = WB_SIO_GPIO34_REG_DATA4,
 306                 .conflict = {
 307                         .name = "UARTD",
 308                         .dev = WB_SIO_DEV_UARTD,
 309                         .testreg = WB_SIO_UARTD_REG_ENABLE,
 310                         .testbit = WB_SIO_UARTD_ENABLE_ON,
 311                         .warnonly = true
 312                 }
 313         },
 314         { /* 4 */
 315                 .dev = WB_SIO_DEV_WDGPIO56,
 316                 .enablereg = WB_SIO_WDGPIO56_REG_ENABLE,
 317                 .enablebit = WB_SIO_WDGPIO56_ENABLE_5,
 318                 .outputreg = WB_SIO_REG_OVTGPIO3456,
 319                 .outputppbit = WB_SIO_REG_OG3456_G5PP,
 320                 .ioreg = WB_SIO_WDGPIO56_REG_IO5,
 321                 .invreg = WB_SIO_WDGPIO56_REG_INV5,
 322                 .datareg = WB_SIO_WDGPIO56_REG_DATA5,
 323                 .conflict = {
 324                         .name = "UARTE",
 325                         .dev = WB_SIO_DEV_UARTE,
 326                         .testreg = WB_SIO_UARTE_REG_ENABLE,
 327                         .testbit = WB_SIO_UARTE_ENABLE_ON,
 328                         .warnonly = true
 329                 }
 330         },
 331         { /* 5 */
 332                 .dev = WB_SIO_DEV_WDGPIO56,
 333                 .enablereg = WB_SIO_WDGPIO56_REG_ENABLE,
 334                 .enablebit = WB_SIO_WDGPIO56_ENABLE_6,
 335                 .outputreg = WB_SIO_REG_OVTGPIO3456,
 336                 .outputppbit = WB_SIO_REG_OG3456_G6PP,
 337                 .ioreg = WB_SIO_WDGPIO56_REG_IO6,
 338                 .invreg = WB_SIO_WDGPIO56_REG_INV6,
 339                 .datareg = WB_SIO_WDGPIO56_REG_DATA6,
 340                 .conflict = {
 341                         .name = "FDC",
 342                         .dev = WB_SIO_DEV_NONE,
 343                         .testreg = WB_SIO_REG_GLOBAL_OPT,
 344                         .testbit = WB_SIO_REG_GO_ENFDC,
 345                         .warnonly = false
 346                 }
 347         }
 348 };
 349 
 350 /* returns whether changing a pin is allowed */
 351 static bool winbond_gpio_get_info(unsigned int *gpio_num,
 352                                   const struct winbond_gpio_info **info)
 353 {
 354         bool allow_changing = true;
 355         unsigned long i;
 356 
 357         for_each_set_bit(i, &params.gpios, BITS_PER_LONG) {
 358                 if (*gpio_num < 8)
 359                         break;
 360 
 361                 *gpio_num -= 8;
 362         }
 363 
 364         *info = &winbond_gpio_infos[i];
 365 
 366         /*
 367          * GPIO2 (the second port) shares some pins with a basic PC
 368          * functionality, which is very likely controlled by the firmware.
 369          * Don't allow changing these pins by default.
 370          */
 371         if (i == 1) {
 372                 if (*gpio_num == 0 && !params.pledgpio)
 373                         allow_changing = false;
 374                 else if (*gpio_num == 1 && !params.beepgpio)
 375                         allow_changing = false;
 376                 else if ((*gpio_num == 5 || *gpio_num == 6) && !params.i2cgpio)
 377                         allow_changing = false;
 378         }
 379 
 380         return allow_changing;
 381 }
 382 
 383 static int winbond_gpio_get(struct gpio_chip *gc, unsigned int offset)
 384 {
 385         unsigned long *base = gpiochip_get_data(gc);
 386         const struct winbond_gpio_info *info;
 387         bool val;
 388 
 389         winbond_gpio_get_info(&offset, &info);
 390 
 391         val = winbond_sio_enter(*base);
 392         if (val)
 393                 return val;
 394 
 395         winbond_sio_select_logical(*base, info->dev);
 396 
 397         val = winbond_sio_reg_btest(*base, info->datareg, offset);
 398         if (winbond_sio_reg_btest(*base, info->invreg, offset))
 399                 val = !val;
 400 
 401         winbond_sio_leave(*base);
 402 
 403         return val;
 404 }
 405 
 406 static int winbond_gpio_direction_in(struct gpio_chip *gc, unsigned int offset)
 407 {
 408         unsigned long *base = gpiochip_get_data(gc);
 409         const struct winbond_gpio_info *info;
 410         int ret;
 411 
 412         if (!winbond_gpio_get_info(&offset, &info))
 413                 return -EACCES;
 414 
 415         ret = winbond_sio_enter(*base);
 416         if (ret)
 417                 return ret;
 418 
 419         winbond_sio_select_logical(*base, info->dev);
 420 
 421         winbond_sio_reg_bset(*base, info->ioreg, offset);
 422 
 423         winbond_sio_leave(*base);
 424 
 425         return 0;
 426 }
 427 
 428 static int winbond_gpio_direction_out(struct gpio_chip *gc,
 429                                       unsigned int offset,
 430                                       int val)
 431 {
 432         unsigned long *base = gpiochip_get_data(gc);
 433         const struct winbond_gpio_info *info;
 434         int ret;
 435 
 436         if (!winbond_gpio_get_info(&offset, &info))
 437                 return -EACCES;
 438 
 439         ret = winbond_sio_enter(*base);
 440         if (ret)
 441                 return ret;
 442 
 443         winbond_sio_select_logical(*base, info->dev);
 444 
 445         winbond_sio_reg_bclear(*base, info->ioreg, offset);
 446 
 447         if (winbond_sio_reg_btest(*base, info->invreg, offset))
 448                 val = !val;
 449 
 450         if (val)
 451                 winbond_sio_reg_bset(*base, info->datareg, offset);
 452         else
 453                 winbond_sio_reg_bclear(*base, info->datareg, offset);
 454 
 455         winbond_sio_leave(*base);
 456 
 457         return 0;
 458 }
 459 
 460 static void winbond_gpio_set(struct gpio_chip *gc, unsigned int offset,
 461                              int val)
 462 {
 463         unsigned long *base = gpiochip_get_data(gc);
 464         const struct winbond_gpio_info *info;
 465 
 466         if (!winbond_gpio_get_info(&offset, &info))
 467                 return;
 468 
 469         if (winbond_sio_enter(*base) != 0)
 470                 return;
 471 
 472         winbond_sio_select_logical(*base, info->dev);
 473 
 474         if (winbond_sio_reg_btest(*base, info->invreg, offset))
 475                 val = !val;
 476 
 477         if (val)
 478                 winbond_sio_reg_bset(*base, info->datareg, offset);
 479         else
 480                 winbond_sio_reg_bclear(*base, info->datareg, offset);
 481 
 482         winbond_sio_leave(*base);
 483 }
 484 
 485 static struct gpio_chip winbond_gpio_chip = {
 486         .base                   = -1,
 487         .label                  = WB_GPIO_DRIVER_NAME,
 488         .owner                  = THIS_MODULE,
 489         .can_sleep              = true,
 490         .get                    = winbond_gpio_get,
 491         .direction_input        = winbond_gpio_direction_in,
 492         .set                    = winbond_gpio_set,
 493         .direction_output       = winbond_gpio_direction_out,
 494 };
 495 
 496 static void winbond_gpio_configure_port0_pins(unsigned long base)
 497 {
 498         unsigned int val;
 499 
 500         val = winbond_sio_reg_read(base, WB_SIO_REG_GPIO1_MF);
 501         if ((val & WB_SIO_REG_G1MF_FS_MASK) == WB_SIO_REG_G1MF_FS_GPIO1)
 502                 return;
 503 
 504         pr_warn("GPIO1 pins were connected to something else (%.2x), fixing\n",
 505                 val);
 506 
 507         val &= ~WB_SIO_REG_G1MF_FS_MASK;
 508         val |= WB_SIO_REG_G1MF_FS_GPIO1;
 509 
 510         winbond_sio_reg_write(base, WB_SIO_REG_GPIO1_MF, val);
 511 }
 512 
 513 static void winbond_gpio_configure_port1_check_i2c(unsigned long base)
 514 {
 515         params.i2cgpio = !winbond_sio_reg_btest(base, WB_SIO_REG_I2C_PS,
 516                                                 WB_SIO_REG_I2CPS_I2CFS);
 517         if (!params.i2cgpio)
 518                 pr_warn("disabling GPIO2.5 and GPIO2.6 as I2C is enabled\n");
 519 }
 520 
 521 static bool winbond_gpio_configure_port(unsigned long base, unsigned int idx)
 522 {
 523         const struct winbond_gpio_info *info = &winbond_gpio_infos[idx];
 524         const struct winbond_gpio_port_conflict *conflict = &info->conflict;
 525 
 526         /* is there a possible conflicting device defined? */
 527         if (conflict->name != NULL) {
 528                 if (conflict->dev != WB_SIO_DEV_NONE)
 529                         winbond_sio_select_logical(base, conflict->dev);
 530 
 531                 if (winbond_sio_reg_btest(base, conflict->testreg,
 532                                           conflict->testbit)) {
 533                         if (conflict->warnonly)
 534                                 pr_warn("enabled GPIO%u share pins with active %s\n",
 535                                         idx + 1, conflict->name);
 536                         else {
 537                                 pr_warn("disabling GPIO%u as %s is enabled\n",
 538                                         idx + 1, conflict->name);
 539                                 return false;
 540                         }
 541                 }
 542         }
 543 
 544         /* GPIO1 and GPIO2 need some (additional) special handling */
 545         if (idx == 0)
 546                 winbond_gpio_configure_port0_pins(base);
 547         else if (idx == 1)
 548                 winbond_gpio_configure_port1_check_i2c(base);
 549 
 550         winbond_sio_select_logical(base, info->dev);
 551 
 552         winbond_sio_reg_bset(base, info->enablereg, info->enablebit);
 553 
 554         if (params.ppgpios & BIT(idx))
 555                 winbond_sio_reg_bset(base, info->outputreg,
 556                                      info->outputppbit);
 557         else if (params.odgpios & BIT(idx))
 558                 winbond_sio_reg_bclear(base, info->outputreg,
 559                                        info->outputppbit);
 560         else
 561                 pr_notice("GPIO%u pins are %s\n", idx + 1,
 562                           winbond_sio_reg_btest(base, info->outputreg,
 563                                                 info->outputppbit) ?
 564                           "push-pull" :
 565                           "open drain");
 566 
 567         return true;
 568 }
 569 
 570 static int winbond_gpio_configure(unsigned long base)
 571 {
 572         unsigned long i;
 573 
 574         for_each_set_bit(i, &params.gpios, BITS_PER_LONG)
 575                 if (!winbond_gpio_configure_port(base, i))
 576                         __clear_bit(i, &params.gpios);
 577 
 578         if (!params.gpios) {
 579                 pr_err("please use 'gpios' module parameter to select some active GPIO ports to enable\n");
 580                 return -EINVAL;
 581         }
 582 
 583         return 0;
 584 }
 585 
 586 static int winbond_gpio_check_chip(unsigned long base)
 587 {
 588         int ret;
 589         unsigned int chip;
 590 
 591         ret = winbond_sio_enter(base);
 592         if (ret)
 593                 return ret;
 594 
 595         chip = winbond_sio_reg_read(base, WB_SIO_REG_CHIP_MSB) << 8;
 596         chip |= winbond_sio_reg_read(base, WB_SIO_REG_CHIP_LSB);
 597 
 598         pr_notice("chip ID at %lx is %.4x\n", base, chip);
 599 
 600         if ((chip & WB_SIO_CHIP_ID_W83627UHG_MASK) !=
 601             WB_SIO_CHIP_ID_W83627UHG) {
 602                 pr_err("not an our chip\n");
 603                 ret = -ENODEV;
 604         }
 605 
 606         winbond_sio_leave(base);
 607 
 608         return ret;
 609 }
 610 
 611 static int winbond_gpio_imatch(struct device *dev, unsigned int id)
 612 {
 613         unsigned long gpios_rem;
 614         int ret;
 615 
 616         gpios_rem = params.gpios & ~GENMASK(ARRAY_SIZE(winbond_gpio_infos) - 1,
 617                                             0);
 618         if (gpios_rem) {
 619                 pr_warn("unknown ports (%lx) enabled in GPIO ports bitmask\n",
 620                         gpios_rem);
 621                 params.gpios &= ~gpios_rem;
 622         }
 623 
 624         if (params.ppgpios & params.odgpios) {
 625                 pr_err("some GPIO ports are set both to push-pull and open drain mode at the same time\n");
 626                 return 0;
 627         }
 628 
 629         if (params.base != 0)
 630                 return winbond_gpio_check_chip(params.base) == 0;
 631 
 632         /*
 633          * if the 'base' module parameter is unset probe two chip default
 634          * I/O port bases
 635          */
 636         params.base = WB_SIO_BASE;
 637         ret = winbond_gpio_check_chip(params.base);
 638         if (ret == 0)
 639                 return 1;
 640         if (ret != -ENODEV && ret != -EBUSY)
 641                 return 0;
 642 
 643         params.base = WB_SIO_BASE_HIGH;
 644         return winbond_gpio_check_chip(params.base) == 0;
 645 }
 646 
 647 static int winbond_gpio_iprobe(struct device *dev, unsigned int id)
 648 {
 649         int ret;
 650 
 651         if (params.base == 0)
 652                 return -EINVAL;
 653 
 654         ret = winbond_sio_enter(params.base);
 655         if (ret)
 656                 return ret;
 657 
 658         ret = winbond_gpio_configure(params.base);
 659 
 660         winbond_sio_leave(params.base);
 661 
 662         if (ret)
 663                 return ret;
 664 
 665         /*
 666          * Add 8 gpios for every GPIO port that was enabled in gpios
 667          * module parameter (that wasn't disabled earlier in
 668          * winbond_gpio_configure() & co. due to, for example, a pin conflict).
 669          */
 670         winbond_gpio_chip.ngpio = hweight_long(params.gpios) * 8;
 671 
 672         /*
 673          * GPIO6 port has only 5 pins, so if it is enabled we have to adjust
 674          * the total count appropriately
 675          */
 676         if (params.gpios & BIT(5))
 677                 winbond_gpio_chip.ngpio -= (8 - 5);
 678 
 679         winbond_gpio_chip.parent = dev;
 680 
 681         return devm_gpiochip_add_data(dev, &winbond_gpio_chip, &params.base);
 682 }
 683 
 684 static struct isa_driver winbond_gpio_idriver = {
 685         .driver = {
 686                 .name   = WB_GPIO_DRIVER_NAME,
 687         },
 688         .match  = winbond_gpio_imatch,
 689         .probe  = winbond_gpio_iprobe,
 690 };
 691 
 692 module_isa_driver(winbond_gpio_idriver, 1);
 693 
 694 module_param_named(base, params.base, ulong, 0444);
 695 MODULE_PARM_DESC(base,
 696                  "I/O port base (when unset - probe chip default ones)");
 697 
 698 /* This parameter sets which GPIO devices (ports) we enable */
 699 module_param_named(gpios, params.gpios, ulong, 0444);
 700 MODULE_PARM_DESC(gpios,
 701                  "bitmask of GPIO ports to enable (bit 0 - GPIO1, bit 1 - GPIO2, etc.");
 702 
 703 /*
 704  * These two parameters below set how we configure GPIO ports output drivers.
 705  * It can't be a one bitmask since we need three values per port: push-pull,
 706  * open-drain and keep as-is (this is the default).
 707  */
 708 module_param_named(ppgpios, params.ppgpios, ulong, 0444);
 709 MODULE_PARM_DESC(ppgpios,
 710                  "bitmask of GPIO ports to set to push-pull mode (bit 0 - GPIO1, bit 1 - GPIO2, etc.");
 711 
 712 module_param_named(odgpios, params.odgpios, ulong, 0444);
 713 MODULE_PARM_DESC(odgpios,
 714                  "bitmask of GPIO ports to set to open drain mode (bit 0 - GPIO1, bit 1 - GPIO2, etc.");
 715 
 716 /*
 717  * GPIO2.0 and GPIO2.1 control a basic PC functionality that we
 718  * don't allow tinkering with by default (it is very likely that the
 719  * firmware owns these pins).
 720  * These two parameters below allow overriding these prohibitions.
 721  */
 722 module_param_named(pledgpio, params.pledgpio, bool, 0644);
 723 MODULE_PARM_DESC(pledgpio,
 724                  "enable changing value of GPIO2.0 bit (Power LED), default no.");
 725 
 726 module_param_named(beepgpio, params.beepgpio, bool, 0644);
 727 MODULE_PARM_DESC(beepgpio,
 728                  "enable changing value of GPIO2.1 bit (BEEP), default no.");
 729 
 730 MODULE_AUTHOR("Maciej S. Szmigiero <mail@maciej.szmigiero.name>");
 731 MODULE_DESCRIPTION("GPIO interface for Winbond Super I/O chips");
 732 MODULE_LICENSE("GPL");
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/gpio/gpio-winbond.c

DEFINITIONS
