drivers/ata/ahci

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
brcm_sata_readreg
brcm_sata_writereg
brcm_sata_alpm_init
brcm_sata_phy_enable
brcm_sata_phy_disable
brcm_sata_phys_enable
brcm_sata_phys_disable
brcm_ahci_get_portmask
brcm_sata_init
brcm_ahci_read_id
brcm_ahci_host_stop
brcm_ahci_suspend
brcm_ahci_resume
brcm_ahci_probe
brcm_ahci_remove
   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * Broadcom SATA3 AHCI Controller Driver
   4  *
   5  * Copyright © 2009-2015 Broadcom Corporation
   6  */
   7 
   8 #include <linux/ahci_platform.h>
   9 #include <linux/compiler.h>
  10 #include <linux/device.h>
  11 #include <linux/init.h>
  12 #include <linux/interrupt.h>
  13 #include <linux/io.h>
  14 #include <linux/kernel.h>
  15 #include <linux/libata.h>
  16 #include <linux/module.h>
  17 #include <linux/of.h>
  18 #include <linux/platform_device.h>
  19 #include <linux/reset.h>
  20 #include <linux/string.h>
  21 
  22 #include "ahci.h"
  23 
  24 #define DRV_NAME                                        "brcm-ahci"
  25 
  26 #define SATA_TOP_CTRL_VERSION                           0x0
  27 #define SATA_TOP_CTRL_BUS_CTRL                          0x4
  28  #define MMIO_ENDIAN_SHIFT                              0 /* CPU->AHCI */
  29  #define DMADESC_ENDIAN_SHIFT                           2 /* AHCI->DDR */
  30  #define DMADATA_ENDIAN_SHIFT                           4 /* AHCI->DDR */
  31  #define PIODATA_ENDIAN_SHIFT                           6
  32   #define ENDIAN_SWAP_NONE                              0
  33   #define ENDIAN_SWAP_FULL                              2
  34 #define SATA_TOP_CTRL_TP_CTRL                           0x8
  35 #define SATA_TOP_CTRL_PHY_CTRL                          0xc
  36  #define SATA_TOP_CTRL_PHY_CTRL_1                       0x0
  37   #define SATA_TOP_CTRL_1_PHY_DEFAULT_POWER_STATE       BIT(14)
  38  #define SATA_TOP_CTRL_PHY_CTRL_2                       0x4
  39   #define SATA_TOP_CTRL_2_SW_RST_MDIOREG                BIT(0)
  40   #define SATA_TOP_CTRL_2_SW_RST_OOB                    BIT(1)
  41   #define SATA_TOP_CTRL_2_SW_RST_RX                     BIT(2)
  42   #define SATA_TOP_CTRL_2_SW_RST_TX                     BIT(3)
  43   #define SATA_TOP_CTRL_2_PHY_GLOBAL_RESET              BIT(14)
  44  #define SATA_TOP_CTRL_PHY_OFFS                         0x8
  45  #define SATA_TOP_MAX_PHYS                              2
  46 
  47 #define SATA_FIRST_PORT_CTRL                            0x700
  48 #define SATA_NEXT_PORT_CTRL_OFFSET                      0x80
  49 #define SATA_PORT_PCTRL6(reg_base)                      (reg_base + 0x18)
  50 
  51 /* On big-endian MIPS, buses are reversed to big endian, so switch them back */
  52 #if defined(CONFIG_MIPS) && defined(__BIG_ENDIAN)
  53 #define DATA_ENDIAN                      2 /* AHCI->DDR inbound accesses */
  54 #define MMIO_ENDIAN                      2 /* CPU->AHCI outbound accesses */
  55 #else
  56 #define DATA_ENDIAN                      0
  57 #define MMIO_ENDIAN                      0
  58 #endif
  59 
  60 #define BUS_CTRL_ENDIAN_CONF                            \
  61         ((DATA_ENDIAN << DMADATA_ENDIAN_SHIFT) |        \
  62         (DATA_ENDIAN << DMADESC_ENDIAN_SHIFT) |         \
  63         (MMIO_ENDIAN << MMIO_ENDIAN_SHIFT))
  64 
  65 #define BUS_CTRL_ENDIAN_NSP_CONF                        \
  66         (0x02 << DMADATA_ENDIAN_SHIFT | 0x02 << DMADESC_ENDIAN_SHIFT)
  67 
  68 #define BUS_CTRL_ENDIAN_CONF_MASK                       \
  69         (0x3 << MMIO_ENDIAN_SHIFT | 0x3 << DMADESC_ENDIAN_SHIFT |       \
  70          0x3 << DMADATA_ENDIAN_SHIFT | 0x3 << PIODATA_ENDIAN_SHIFT)
  71 
  72 enum brcm_ahci_version {
  73         BRCM_SATA_BCM7425 = 1,
  74         BRCM_SATA_BCM7445,
  75         BRCM_SATA_NSP,
  76 };
  77 
  78 enum brcm_ahci_quirks {
  79         BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE = BIT(0),
  80 };
  81 
  82 struct brcm_ahci_priv {
  83         struct device *dev;
  84         void __iomem *top_ctrl;
  85         u32 port_mask;
  86         u32 quirks;
  87         enum brcm_ahci_version version;
  88         struct reset_control *rcdev;
  89 };
  90 
  91 static inline u32 brcm_sata_readreg(void __iomem *addr)
  92 {
  93         /*
  94          * MIPS endianness is configured by boot strap, which also reverses all
  95          * bus endianness (i.e., big-endian CPU + big endian bus ==> native
  96          * endian I/O).
  97          *
  98          * Other architectures (e.g., ARM) either do not support big endian, or
  99          * else leave I/O in little endian mode.
 100          */
 101         if (IS_ENABLED(CONFIG_MIPS) && IS_ENABLED(CONFIG_CPU_BIG_ENDIAN))
 102                 return __raw_readl(addr);
 103         else
 104                 return readl_relaxed(addr);
 105 }
 106 
 107 static inline void brcm_sata_writereg(u32 val, void __iomem *addr)
 108 {
 109         /* See brcm_sata_readreg() comments */
 110         if (IS_ENABLED(CONFIG_MIPS) && IS_ENABLED(CONFIG_CPU_BIG_ENDIAN))
 111                 __raw_writel(val, addr);
 112         else
 113                 writel_relaxed(val, addr);
 114 }
 115 
 116 static void brcm_sata_alpm_init(struct ahci_host_priv *hpriv)
 117 {
 118         struct brcm_ahci_priv *priv = hpriv->plat_data;
 119         u32 port_ctrl, host_caps;
 120         int i;
 121 
 122         /* Enable support for ALPM */
 123         host_caps = readl(hpriv->mmio + HOST_CAP);
 124         if (!(host_caps & HOST_CAP_ALPM))
 125                 hpriv->flags |= AHCI_HFLAG_YES_ALPM;
 126 
 127         /*
 128          * Adjust timeout to allow PLL sufficient time to lock while waking
 129          * up from slumber mode.
 130          */
 131         for (i = 0, port_ctrl = SATA_FIRST_PORT_CTRL;
 132              i < SATA_TOP_MAX_PHYS;
 133              i++, port_ctrl += SATA_NEXT_PORT_CTRL_OFFSET) {
 134                 if (priv->port_mask & BIT(i))
 135                         writel(0xff1003fc,
 136                                hpriv->mmio + SATA_PORT_PCTRL6(port_ctrl));
 137         }
 138 }
 139 
 140 static void brcm_sata_phy_enable(struct brcm_ahci_priv *priv, int port)
 141 {
 142         void __iomem *phyctrl = priv->top_ctrl + SATA_TOP_CTRL_PHY_CTRL +
 143                                 (port * SATA_TOP_CTRL_PHY_OFFS);
 144         void __iomem *p;
 145         u32 reg;
 146 
 147         if (priv->quirks & BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE)
 148                 return;
 149 
 150         /* clear PHY_DEFAULT_POWER_STATE */
 151         p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_1;
 152         reg = brcm_sata_readreg(p);
 153         reg &= ~SATA_TOP_CTRL_1_PHY_DEFAULT_POWER_STATE;
 154         brcm_sata_writereg(reg, p);
 155 
 156         /* reset the PHY digital logic */
 157         p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_2;
 158         reg = brcm_sata_readreg(p);
 159         reg &= ~(SATA_TOP_CTRL_2_SW_RST_MDIOREG | SATA_TOP_CTRL_2_SW_RST_OOB |
 160                  SATA_TOP_CTRL_2_SW_RST_RX);
 161         reg |= SATA_TOP_CTRL_2_SW_RST_TX;
 162         brcm_sata_writereg(reg, p);
 163         reg = brcm_sata_readreg(p);
 164         reg |= SATA_TOP_CTRL_2_PHY_GLOBAL_RESET;
 165         brcm_sata_writereg(reg, p);
 166         reg = brcm_sata_readreg(p);
 167         reg &= ~SATA_TOP_CTRL_2_PHY_GLOBAL_RESET;
 168         brcm_sata_writereg(reg, p);
 169         (void)brcm_sata_readreg(p);
 170 }
 171 
 172 static void brcm_sata_phy_disable(struct brcm_ahci_priv *priv, int port)
 173 {
 174         void __iomem *phyctrl = priv->top_ctrl + SATA_TOP_CTRL_PHY_CTRL +
 175                                 (port * SATA_TOP_CTRL_PHY_OFFS);
 176         void __iomem *p;
 177         u32 reg;
 178 
 179         if (priv->quirks & BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE)
 180                 return;
 181 
 182         /* power-off the PHY digital logic */
 183         p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_2;
 184         reg = brcm_sata_readreg(p);
 185         reg |= (SATA_TOP_CTRL_2_SW_RST_MDIOREG | SATA_TOP_CTRL_2_SW_RST_OOB |
 186                 SATA_TOP_CTRL_2_SW_RST_RX | SATA_TOP_CTRL_2_SW_RST_TX |
 187                 SATA_TOP_CTRL_2_PHY_GLOBAL_RESET);
 188         brcm_sata_writereg(reg, p);
 189 
 190         /* set PHY_DEFAULT_POWER_STATE */
 191         p = phyctrl + SATA_TOP_CTRL_PHY_CTRL_1;
 192         reg = brcm_sata_readreg(p);
 193         reg |= SATA_TOP_CTRL_1_PHY_DEFAULT_POWER_STATE;
 194         brcm_sata_writereg(reg, p);
 195 }
 196 
 197 static void brcm_sata_phys_enable(struct brcm_ahci_priv *priv)
 198 {
 199         int i;
 200 
 201         for (i = 0; i < SATA_TOP_MAX_PHYS; i++)
 202                 if (priv->port_mask & BIT(i))
 203                         brcm_sata_phy_enable(priv, i);
 204 }
 205 
 206 static void brcm_sata_phys_disable(struct brcm_ahci_priv *priv)
 207 {
 208         int i;
 209 
 210         for (i = 0; i < SATA_TOP_MAX_PHYS; i++)
 211                 if (priv->port_mask & BIT(i))
 212                         brcm_sata_phy_disable(priv, i);
 213 }
 214 
 215 static u32 brcm_ahci_get_portmask(struct ahci_host_priv *hpriv,
 216                                   struct brcm_ahci_priv *priv)
 217 {
 218         u32 impl;
 219 
 220         impl = readl(hpriv->mmio + HOST_PORTS_IMPL);
 221 
 222         if (fls(impl) > SATA_TOP_MAX_PHYS)
 223                 dev_warn(priv->dev, "warning: more ports than PHYs (%#x)\n",
 224                          impl);
 225         else if (!impl)
 226                 dev_info(priv->dev, "no ports found\n");
 227 
 228         return impl;
 229 }
 230 
 231 static void brcm_sata_init(struct brcm_ahci_priv *priv)
 232 {
 233         void __iomem *ctrl = priv->top_ctrl + SATA_TOP_CTRL_BUS_CTRL;
 234         u32 data;
 235 
 236         /* Configure endianness */
 237         data = brcm_sata_readreg(ctrl);
 238         data &= ~BUS_CTRL_ENDIAN_CONF_MASK;
 239         if (priv->version == BRCM_SATA_NSP)
 240                 data |= BUS_CTRL_ENDIAN_NSP_CONF;
 241         else
 242                 data |= BUS_CTRL_ENDIAN_CONF;
 243         brcm_sata_writereg(data, ctrl);
 244 }
 245 
 246 static unsigned int brcm_ahci_read_id(struct ata_device *dev,
 247                                       struct ata_taskfile *tf, u16 *id)
 248 {
 249         struct ata_port *ap = dev->link->ap;
 250         struct ata_host *host = ap->host;
 251         struct ahci_host_priv *hpriv = host->private_data;
 252         struct brcm_ahci_priv *priv = hpriv->plat_data;
 253         void __iomem *mmio = hpriv->mmio;
 254         unsigned int err_mask;
 255         unsigned long flags;
 256         int i, rc;
 257         u32 ctl;
 258 
 259         /* Try to read the device ID and, if this fails, proceed with the
 260          * recovery sequence below
 261          */
 262         err_mask = ata_do_dev_read_id(dev, tf, id);
 263         if (likely(!err_mask))
 264                 return err_mask;
 265 
 266         /* Disable host interrupts */
 267         spin_lock_irqsave(&host->lock, flags);
 268         ctl = readl(mmio + HOST_CTL);
 269         ctl &= ~HOST_IRQ_EN;
 270         writel(ctl, mmio + HOST_CTL);
 271         readl(mmio + HOST_CTL); /* flush */
 272         spin_unlock_irqrestore(&host->lock, flags);
 273 
 274         /* Perform the SATA PHY reset sequence */
 275         brcm_sata_phy_disable(priv, ap->port_no);
 276 
 277         /* Reset the SATA clock */
 278         ahci_platform_disable_clks(hpriv);
 279         msleep(10);
 280 
 281         ahci_platform_enable_clks(hpriv);
 282         msleep(10);
 283 
 284         /* Bring the PHY back on */
 285         brcm_sata_phy_enable(priv, ap->port_no);
 286 
 287         /* Re-initialize and calibrate the PHY */
 288         for (i = 0; i < hpriv->nports; i++) {
 289                 rc = phy_init(hpriv->phys[i]);
 290                 if (rc)
 291                         goto disable_phys;
 292 
 293                 rc = phy_calibrate(hpriv->phys[i]);
 294                 if (rc) {
 295                         phy_exit(hpriv->phys[i]);
 296                         goto disable_phys;
 297                 }
 298         }
 299 
 300         /* Re-enable host interrupts */
 301         spin_lock_irqsave(&host->lock, flags);
 302         ctl = readl(mmio + HOST_CTL);
 303         ctl |= HOST_IRQ_EN;
 304         writel(ctl, mmio + HOST_CTL);
 305         readl(mmio + HOST_CTL); /* flush */
 306         spin_unlock_irqrestore(&host->lock, flags);
 307 
 308         return ata_do_dev_read_id(dev, tf, id);
 309 
 310 disable_phys:
 311         while (--i >= 0) {
 312                 phy_power_off(hpriv->phys[i]);
 313                 phy_exit(hpriv->phys[i]);
 314         }
 315 
 316         return AC_ERR_OTHER;
 317 }
 318 
 319 static void brcm_ahci_host_stop(struct ata_host *host)
 320 {
 321         struct ahci_host_priv *hpriv = host->private_data;
 322 
 323         ahci_platform_disable_resources(hpriv);
 324 }
 325 
 326 static struct ata_port_operations ahci_brcm_platform_ops = {
 327         .inherits       = &ahci_ops,
 328         .host_stop      = brcm_ahci_host_stop,
 329         .read_id        = brcm_ahci_read_id,
 330 };
 331 
 332 static const struct ata_port_info ahci_brcm_port_info = {
 333         .flags          = AHCI_FLAG_COMMON | ATA_FLAG_NO_DIPM,
 334         .link_flags     = ATA_LFLAG_NO_DB_DELAY,
 335         .pio_mask       = ATA_PIO4,
 336         .udma_mask      = ATA_UDMA6,
 337         .port_ops       = &ahci_brcm_platform_ops,
 338 };
 339 
 340 #ifdef CONFIG_PM_SLEEP
 341 static int brcm_ahci_suspend(struct device *dev)
 342 {
 343         struct ata_host *host = dev_get_drvdata(dev);
 344         struct ahci_host_priv *hpriv = host->private_data;
 345         struct brcm_ahci_priv *priv = hpriv->plat_data;
 346 
 347         brcm_sata_phys_disable(priv);
 348 
 349         return ahci_platform_suspend(dev);
 350 }
 351 
 352 static int brcm_ahci_resume(struct device *dev)
 353 {
 354         struct ata_host *host = dev_get_drvdata(dev);
 355         struct ahci_host_priv *hpriv = host->private_data;
 356         struct brcm_ahci_priv *priv = hpriv->plat_data;
 357         int ret;
 358 
 359         /* Make sure clocks are turned on before re-configuration */
 360         ret = ahci_platform_enable_clks(hpriv);
 361         if (ret)
 362                 return ret;
 363 
 364         brcm_sata_init(priv);
 365         brcm_sata_phys_enable(priv);
 366         brcm_sata_alpm_init(hpriv);
 367 
 368         /* Since we had to enable clocks earlier on, we cannot use
 369          * ahci_platform_resume() as-is since a second call to
 370          * ahci_platform_enable_resources() would bump up the resources
 371          * (regulators, clocks, PHYs) count artificially so we copy the part
 372          * after ahci_platform_enable_resources().
 373          */
 374         ret = ahci_platform_enable_phys(hpriv);
 375         if (ret)
 376                 goto out_disable_phys;
 377 
 378         ret = ahci_platform_resume_host(dev);
 379         if (ret)
 380                 goto out_disable_platform_phys;
 381 
 382         /* We resumed so update PM runtime state */
 383         pm_runtime_disable(dev);
 384         pm_runtime_set_active(dev);
 385         pm_runtime_enable(dev);
 386 
 387         return 0;
 388 
 389 out_disable_platform_phys:
 390         ahci_platform_disable_phys(hpriv);
 391 out_disable_phys:
 392         brcm_sata_phys_disable(priv);
 393         ahci_platform_disable_clks(hpriv);
 394         return ret;
 395 }
 396 #endif
 397 
 398 static struct scsi_host_template ahci_platform_sht = {
 399         AHCI_SHT(DRV_NAME),
 400 };
 401 
 402 static const struct of_device_id ahci_of_match[] = {
 403         {.compatible = "brcm,bcm7425-ahci", .data = (void *)BRCM_SATA_BCM7425},
 404         {.compatible = "brcm,bcm7445-ahci", .data = (void *)BRCM_SATA_BCM7445},
 405         {.compatible = "brcm,bcm63138-ahci", .data = (void *)BRCM_SATA_BCM7445},
 406         {.compatible = "brcm,bcm-nsp-ahci", .data = (void *)BRCM_SATA_NSP},
 407         {},
 408 };
 409 MODULE_DEVICE_TABLE(of, ahci_of_match);
 410 
 411 static int brcm_ahci_probe(struct platform_device *pdev)
 412 {
 413         const struct of_device_id *of_id;
 414         struct device *dev = &pdev->dev;
 415         struct brcm_ahci_priv *priv;
 416         struct ahci_host_priv *hpriv;
 417         struct resource *res;
 418         int ret;
 419 
 420         priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
 421         if (!priv)
 422                 return -ENOMEM;
 423 
 424         of_id = of_match_node(ahci_of_match, pdev->dev.of_node);
 425         if (!of_id)
 426                 return -ENODEV;
 427 
 428         priv->version = (enum brcm_ahci_version)of_id->data;
 429         priv->dev = dev;
 430 
 431         res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "top-ctrl");
 432         priv->top_ctrl = devm_ioremap_resource(dev, res);
 433         if (IS_ERR(priv->top_ctrl))
 434                 return PTR_ERR(priv->top_ctrl);
 435 
 436         /* Reset is optional depending on platform */
 437         priv->rcdev = devm_reset_control_get(&pdev->dev, "ahci");
 438         if (!IS_ERR_OR_NULL(priv->rcdev))
 439                 reset_control_deassert(priv->rcdev);
 440 
 441         hpriv = ahci_platform_get_resources(pdev, 0);
 442         if (IS_ERR(hpriv)) {
 443                 ret = PTR_ERR(hpriv);
 444                 goto out_reset;
 445         }
 446 
 447         hpriv->plat_data = priv;
 448         hpriv->flags = AHCI_HFLAG_WAKE_BEFORE_STOP | AHCI_HFLAG_NO_WRITE_TO_RO;
 449 
 450         switch (priv->version) {
 451         case BRCM_SATA_BCM7425:
 452                 hpriv->flags |= AHCI_HFLAG_DELAY_ENGINE;
 453                 /* fall through */
 454         case BRCM_SATA_NSP:
 455                 hpriv->flags |= AHCI_HFLAG_NO_NCQ;
 456                 priv->quirks |= BRCM_AHCI_QUIRK_SKIP_PHY_ENABLE;
 457                 break;
 458         default:
 459                 break;
 460         }
 461 
 462         ret = ahci_platform_enable_clks(hpriv);
 463         if (ret)
 464                 goto out_reset;
 465 
 466         /* Must be first so as to configure endianness including that
 467          * of the standard AHCI register space.
 468          */
 469         brcm_sata_init(priv);
 470 
 471         /* Initializes priv->port_mask which is used below */
 472         priv->port_mask = brcm_ahci_get_portmask(hpriv, priv);
 473         if (!priv->port_mask) {
 474                 ret = -ENODEV;
 475                 goto out_disable_clks;
 476         }
 477 
 478         /* Must be done before ahci_platform_enable_phys() */
 479         brcm_sata_phys_enable(priv);
 480 
 481         brcm_sata_alpm_init(hpriv);
 482 
 483         ret = ahci_platform_enable_phys(hpriv);
 484         if (ret)
 485                 goto out_disable_phys;
 486 
 487         ret = ahci_platform_init_host(pdev, hpriv, &ahci_brcm_port_info,
 488                                       &ahci_platform_sht);
 489         if (ret)
 490                 goto out_disable_platform_phys;
 491 
 492         dev_info(dev, "Broadcom AHCI SATA3 registered\n");
 493 
 494         return 0;
 495 
 496 out_disable_platform_phys:
 497         ahci_platform_disable_phys(hpriv);
 498 out_disable_phys:
 499         brcm_sata_phys_disable(priv);
 500 out_disable_clks:
 501         ahci_platform_disable_clks(hpriv);
 502 out_reset:
 503         if (!IS_ERR_OR_NULL(priv->rcdev))
 504                 reset_control_assert(priv->rcdev);
 505         return ret;
 506 }
 507 
 508 static int brcm_ahci_remove(struct platform_device *pdev)
 509 {
 510         struct ata_host *host = dev_get_drvdata(&pdev->dev);
 511         struct ahci_host_priv *hpriv = host->private_data;
 512         struct brcm_ahci_priv *priv = hpriv->plat_data;
 513         int ret;
 514 
 515         brcm_sata_phys_disable(priv);
 516 
 517         ret = ata_platform_remove_one(pdev);
 518         if (ret)
 519                 return ret;
 520 
 521         return 0;
 522 }
 523 
 524 static SIMPLE_DEV_PM_OPS(ahci_brcm_pm_ops, brcm_ahci_suspend, brcm_ahci_resume);
 525 
 526 static struct platform_driver brcm_ahci_driver = {
 527         .probe = brcm_ahci_probe,
 528         .remove = brcm_ahci_remove,
 529         .driver = {
 530                 .name = DRV_NAME,
 531                 .of_match_table = ahci_of_match,
 532                 .pm = &ahci_brcm_pm_ops,
 533         },
 534 };
 535 module_platform_driver(brcm_ahci_driver);
 536 
 537 MODULE_DESCRIPTION("Broadcom SATA3 AHCI Controller Driver");
 538 MODULE_AUTHOR("Brian Norris");
 539 MODULE_LICENSE("GPL");
 540 MODULE_ALIAS("platform:sata-brcmstb");
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/ata/ahci_brcm.c

DEFINITIONS
