root/drivers/usb/host/ohci-nxp.c

/* [<][>][^][v][top][bottom][index][help] */

DEFINITIONS

This source file includes following definitions.
  1. isp1301_configure_lpc32xx
  2. isp1301_configure
  3. isp1301_vbus_on
  4. isp1301_vbus_off
  5. ohci_nxp_start_hc
  6. ohci_nxp_stop_hc
  7. ohci_hcd_nxp_probe
  8. ohci_hcd_nxp_remove
  9. ohci_nxp_init
  10. ohci_nxp_cleanup

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * driver for NXP USB Host devices
   4  *
   5  * Currently supported OHCI host devices:
   6  * - NXP LPC32xx
   7  *
   8  * Authors: Dmitry Chigirev <source@mvista.com>
   9  *          Vitaly Wool <vitalywool@gmail.com>
  10  *
  11  * register initialization is based on code examples provided by Philips
  12  * Copyright (c) 2005 Koninklijke Philips Electronics N.V.
  13  *
  14  * NOTE: This driver does not have suspend/resume functionality
  15  * This driver is intended for engineering development purposes only
  16  *
  17  * 2005-2006 (c) MontaVista Software, Inc.
  18  */
  19 #include <linux/clk.h>
  20 #include <linux/dma-mapping.h>
  21 #include <linux/io.h>
  22 #include <linux/i2c.h>
  23 #include <linux/module.h>
  24 #include <linux/of.h>
  25 #include <linux/platform_device.h>
  26 #include <linux/usb/isp1301.h>
  27 #include <linux/usb.h>
  28 #include <linux/usb/hcd.h>
  29 
  30 #include "ohci.h"
  31 
  32 #define USB_CONFIG_BASE         0x31020000
  33 
  34 /* USB_OTG_STAT_CONTROL bit defines */
  35 #define TRANSPARENT_I2C_EN      (1 << 7)
  36 #define HOST_EN                 (1 << 0)
  37 
  38 /* On LPC32xx, those are undefined */
  39 #ifndef start_int_set_falling_edge
  40 #define start_int_set_falling_edge(irq)
  41 #define start_int_set_rising_edge(irq)
  42 #define start_int_ack(irq)
  43 #define start_int_mask(irq)
  44 #define start_int_umask(irq)
  45 #endif
  46 
  47 #define DRIVER_DESC "OHCI NXP driver"
  48 
  49 static const char hcd_name[] = "ohci-nxp";
  50 static struct hc_driver __read_mostly ohci_nxp_hc_driver;
  51 
  52 static struct i2c_client *isp1301_i2c_client;
  53 
  54 static struct clk *usb_host_clk;
  55 
  56 static void isp1301_configure_lpc32xx(void)
  57 {
  58         /* LPC32XX only supports DAT_SE0 USB mode */
  59         /* This sequence is important */
  60 
  61         /* Disable transparent UART mode first */
  62         i2c_smbus_write_byte_data(isp1301_i2c_client,
  63                 (ISP1301_I2C_MODE_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR),
  64                 MC1_UART_EN);
  65         i2c_smbus_write_byte_data(isp1301_i2c_client,
  66                 (ISP1301_I2C_MODE_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR),
  67                 ~MC1_SPEED_REG);
  68         i2c_smbus_write_byte_data(isp1301_i2c_client,
  69                                   ISP1301_I2C_MODE_CONTROL_1, MC1_SPEED_REG);
  70         i2c_smbus_write_byte_data(isp1301_i2c_client,
  71                   (ISP1301_I2C_MODE_CONTROL_2 | ISP1301_I2C_REG_CLEAR_ADDR),
  72                   ~0);
  73         i2c_smbus_write_byte_data(isp1301_i2c_client,
  74                 ISP1301_I2C_MODE_CONTROL_2,
  75                 (MC2_BI_DI | MC2_PSW_EN | MC2_SPD_SUSP_CTRL));
  76         i2c_smbus_write_byte_data(isp1301_i2c_client,
  77                 (ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR), ~0);
  78         i2c_smbus_write_byte_data(isp1301_i2c_client,
  79                 ISP1301_I2C_MODE_CONTROL_1, MC1_DAT_SE0);
  80         i2c_smbus_write_byte_data(isp1301_i2c_client,
  81                 ISP1301_I2C_OTG_CONTROL_1,
  82                 (OTG1_DM_PULLDOWN | OTG1_DP_PULLDOWN));
  83         i2c_smbus_write_byte_data(isp1301_i2c_client,
  84                 (ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR),
  85                 (OTG1_DM_PULLUP | OTG1_DP_PULLUP));
  86         i2c_smbus_write_byte_data(isp1301_i2c_client,
  87                 ISP1301_I2C_INTERRUPT_LATCH | ISP1301_I2C_REG_CLEAR_ADDR, ~0);
  88         i2c_smbus_write_byte_data(isp1301_i2c_client,
  89                 ISP1301_I2C_INTERRUPT_FALLING | ISP1301_I2C_REG_CLEAR_ADDR,
  90                 ~0);
  91         i2c_smbus_write_byte_data(isp1301_i2c_client,
  92                 ISP1301_I2C_INTERRUPT_RISING | ISP1301_I2C_REG_CLEAR_ADDR, ~0);
  93 
  94         printk(KERN_INFO "ISP1301 Vendor ID  : 0x%04x\n",
  95               i2c_smbus_read_word_data(isp1301_i2c_client, 0x00));
  96         printk(KERN_INFO "ISP1301 Product ID : 0x%04x\n",
  97               i2c_smbus_read_word_data(isp1301_i2c_client, 0x02));
  98         printk(KERN_INFO "ISP1301 Version ID : 0x%04x\n",
  99               i2c_smbus_read_word_data(isp1301_i2c_client, 0x14));
 100 }
 101 
 102 static void isp1301_configure(void)
 103 {
 104         isp1301_configure_lpc32xx();
 105 }
 106 
 107 static inline void isp1301_vbus_on(void)
 108 {
 109         i2c_smbus_write_byte_data(isp1301_i2c_client, ISP1301_I2C_OTG_CONTROL_1,
 110                                   OTG1_VBUS_DRV);
 111 }
 112 
 113 static inline void isp1301_vbus_off(void)
 114 {
 115         i2c_smbus_write_byte_data(isp1301_i2c_client,
 116                 ISP1301_I2C_OTG_CONTROL_1 | ISP1301_I2C_REG_CLEAR_ADDR,
 117                 OTG1_VBUS_DRV);
 118 }
 119 
 120 static void ohci_nxp_start_hc(void)
 121 {
 122         void __iomem *usb_otg_stat_control = ioremap(USB_CONFIG_BASE + 0x110, 4);
 123         unsigned long tmp;
 124 
 125         if (WARN_ON(!usb_otg_stat_control))
 126                 return;
 127 
 128         tmp = __raw_readl(usb_otg_stat_control) | HOST_EN;
 129 
 130         __raw_writel(tmp, usb_otg_stat_control);
 131         isp1301_vbus_on();
 132 
 133         iounmap(usb_otg_stat_control);
 134 }
 135 
 136 static void ohci_nxp_stop_hc(void)
 137 {
 138         void __iomem *usb_otg_stat_control = ioremap(USB_CONFIG_BASE + 0x110, 4);
 139         unsigned long tmp;
 140 
 141         if (WARN_ON(!usb_otg_stat_control))
 142                 return;
 143 
 144         isp1301_vbus_off();
 145         tmp = __raw_readl(usb_otg_stat_control) & ~HOST_EN;
 146         __raw_writel(tmp, usb_otg_stat_control);
 147 
 148         iounmap(usb_otg_stat_control);
 149 }
 150 
 151 static int ohci_hcd_nxp_probe(struct platform_device *pdev)
 152 {
 153         struct usb_hcd *hcd = 0;
 154         const struct hc_driver *driver = &ohci_nxp_hc_driver;
 155         struct resource *res;
 156         int ret = 0, irq;
 157         struct device_node *isp1301_node;
 158 
 159         if (pdev->dev.of_node) {
 160                 isp1301_node = of_parse_phandle(pdev->dev.of_node,
 161                                                 "transceiver", 0);
 162         } else {
 163                 isp1301_node = NULL;
 164         }
 165 
 166         isp1301_i2c_client = isp1301_get_client(isp1301_node);
 167         if (!isp1301_i2c_client)
 168                 return -EPROBE_DEFER;
 169 
 170         ret = dma_coerce_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
 171         if (ret)
 172                 goto fail_disable;
 173 
 174         dev_dbg(&pdev->dev, "%s: " DRIVER_DESC " (nxp)\n", hcd_name);
 175         if (usb_disabled()) {
 176                 dev_err(&pdev->dev, "USB is disabled\n");
 177                 ret = -ENODEV;
 178                 goto fail_disable;
 179         }
 180 
 181         /* Enable USB host clock */
 182         usb_host_clk = devm_clk_get(&pdev->dev, NULL);
 183         if (IS_ERR(usb_host_clk)) {
 184                 dev_err(&pdev->dev, "failed to acquire USB OHCI clock\n");
 185                 ret = PTR_ERR(usb_host_clk);
 186                 goto fail_disable;
 187         }
 188 
 189         ret = clk_prepare_enable(usb_host_clk);
 190         if (ret < 0) {
 191                 dev_err(&pdev->dev, "failed to start USB OHCI clock\n");
 192                 goto fail_disable;
 193         }
 194 
 195         isp1301_configure();
 196 
 197         hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev));
 198         if (!hcd) {
 199                 dev_err(&pdev->dev, "Failed to allocate HC buffer\n");
 200                 ret = -ENOMEM;
 201                 goto fail_hcd;
 202         }
 203 
 204         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 205         hcd->regs = devm_ioremap_resource(&pdev->dev, res);
 206         if (IS_ERR(hcd->regs)) {
 207                 ret = PTR_ERR(hcd->regs);
 208                 goto fail_resource;
 209         }
 210         hcd->rsrc_start = res->start;
 211         hcd->rsrc_len = resource_size(res);
 212 
 213         irq = platform_get_irq(pdev, 0);
 214         if (irq < 0) {
 215                 ret = -ENXIO;
 216                 goto fail_resource;
 217         }
 218 
 219         ohci_nxp_start_hc();
 220         platform_set_drvdata(pdev, hcd);
 221 
 222         dev_info(&pdev->dev, "at 0x%p, irq %d\n", hcd->regs, hcd->irq);
 223         ret = usb_add_hcd(hcd, irq, 0);
 224         if (ret == 0) {
 225                 device_wakeup_enable(hcd->self.controller);
 226                 return ret;
 227         }
 228 
 229         ohci_nxp_stop_hc();
 230 fail_resource:
 231         usb_put_hcd(hcd);
 232 fail_hcd:
 233         clk_disable_unprepare(usb_host_clk);
 234 fail_disable:
 235         isp1301_i2c_client = NULL;
 236         return ret;
 237 }
 238 
 239 static int ohci_hcd_nxp_remove(struct platform_device *pdev)
 240 {
 241         struct usb_hcd *hcd = platform_get_drvdata(pdev);
 242 
 243         usb_remove_hcd(hcd);
 244         ohci_nxp_stop_hc();
 245         usb_put_hcd(hcd);
 246         clk_disable_unprepare(usb_host_clk);
 247         isp1301_i2c_client = NULL;
 248 
 249         return 0;
 250 }
 251 
 252 /* work with hotplug and coldplug */
 253 MODULE_ALIAS("platform:usb-ohci");
 254 
 255 #ifdef CONFIG_OF
 256 static const struct of_device_id ohci_hcd_nxp_match[] = {
 257         { .compatible = "nxp,ohci-nxp" },
 258         {},
 259 };
 260 MODULE_DEVICE_TABLE(of, ohci_hcd_nxp_match);
 261 #endif
 262 
 263 static struct platform_driver ohci_hcd_nxp_driver = {
 264         .driver = {
 265                 .name = "usb-ohci",
 266                 .of_match_table = of_match_ptr(ohci_hcd_nxp_match),
 267         },
 268         .probe = ohci_hcd_nxp_probe,
 269         .remove = ohci_hcd_nxp_remove,
 270 };
 271 
 272 static int __init ohci_nxp_init(void)
 273 {
 274         if (usb_disabled())
 275                 return -ENODEV;
 276 
 277         pr_info("%s: " DRIVER_DESC "\n", hcd_name);
 278 
 279         ohci_init_driver(&ohci_nxp_hc_driver, NULL);
 280         return platform_driver_register(&ohci_hcd_nxp_driver);
 281 }
 282 module_init(ohci_nxp_init);
 283 
 284 static void __exit ohci_nxp_cleanup(void)
 285 {
 286         platform_driver_unregister(&ohci_hcd_nxp_driver);
 287 }
 288 module_exit(ohci_nxp_cleanup);
 289 
 290 MODULE_DESCRIPTION(DRIVER_DESC);
 291 MODULE_LICENSE("GPL v2");

/* [<][>][^][v][top][bottom][index][help] */