This source file includes following definitions.
- lpc18xx_rs485_config
- lpc18xx_uart_serial_out
- lpc18xx_serial_probe
- lpc18xx_serial_remove
1
2
3
4
5
6
7
8
9
10
11
12 #include <linux/clk.h>
13 #include <linux/io.h>
14 #include <linux/module.h>
15 #include <linux/of.h>
16 #include <linux/platform_device.h>
17
18 #include "8250.h"
19
20
21 #define LPC18XX_UART_RS485CTRL (0x04c / sizeof(u32))
22 #define LPC18XX_UART_RS485CTRL_NMMEN BIT(0)
23 #define LPC18XX_UART_RS485CTRL_DCTRL BIT(4)
24 #define LPC18XX_UART_RS485CTRL_OINV BIT(5)
25 #define LPC18XX_UART_RS485DLY (0x054 / sizeof(u32))
26 #define LPC18XX_UART_RS485DLY_MAX 255
27
28 struct lpc18xx_uart_data {
29 struct uart_8250_dma dma;
30 struct clk *clk_uart;
31 struct clk *clk_reg;
32 int line;
33 };
34
35 static int lpc18xx_rs485_config(struct uart_port *port,
36 struct serial_rs485 *rs485)
37 {
38 struct uart_8250_port *up = up_to_u8250p(port);
39 u32 rs485_ctrl_reg = 0;
40 u32 rs485_dly_reg = 0;
41 unsigned baud_clk;
42
43 if (rs485->flags & SER_RS485_ENABLED)
44 memset(rs485->padding, 0, sizeof(rs485->padding));
45 else
46 memset(rs485, 0, sizeof(*rs485));
47
48 rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
49 SER_RS485_RTS_AFTER_SEND;
50
51 if (rs485->flags & SER_RS485_ENABLED) {
52 rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_NMMEN |
53 LPC18XX_UART_RS485CTRL_DCTRL;
54
55 if (rs485->flags & SER_RS485_RTS_ON_SEND) {
56 rs485_ctrl_reg |= LPC18XX_UART_RS485CTRL_OINV;
57 rs485->flags &= ~SER_RS485_RTS_AFTER_SEND;
58 } else {
59 rs485->flags |= SER_RS485_RTS_AFTER_SEND;
60 }
61 }
62
63 if (rs485->delay_rts_after_send) {
64 baud_clk = port->uartclk / up->dl_read(up);
65 rs485_dly_reg = DIV_ROUND_UP(rs485->delay_rts_after_send
66 * baud_clk, MSEC_PER_SEC);
67
68 if (rs485_dly_reg > LPC18XX_UART_RS485DLY_MAX)
69 rs485_dly_reg = LPC18XX_UART_RS485DLY_MAX;
70
71
72 rs485->delay_rts_after_send = (rs485_dly_reg * MSEC_PER_SEC)
73 / baud_clk;
74 }
75
76
77 rs485->delay_rts_before_send = 0;
78
79 serial_out(up, LPC18XX_UART_RS485CTRL, rs485_ctrl_reg);
80 serial_out(up, LPC18XX_UART_RS485DLY, rs485_dly_reg);
81
82 port->rs485 = *rs485;
83
84 return 0;
85 }
86
87 static void lpc18xx_uart_serial_out(struct uart_port *p, int offset, int value)
88 {
89
90
91
92
93
94 if (offset == UART_FCR && (value & UART_FCR_ENABLE_FIFO))
95 value |= UART_FCR_DMA_SELECT;
96
97 offset = offset << p->regshift;
98 writel(value, p->membase + offset);
99 }
100
101 static int lpc18xx_serial_probe(struct platform_device *pdev)
102 {
103 struct lpc18xx_uart_data *data;
104 struct uart_8250_port uart;
105 struct resource *res;
106 int irq, ret;
107
108 irq = platform_get_irq(pdev, 0);
109 if (irq < 0)
110 return irq;
111
112 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
113 if (!res) {
114 dev_err(&pdev->dev, "memory resource not found");
115 return -EINVAL;
116 }
117
118 memset(&uart, 0, sizeof(uart));
119
120 uart.port.membase = devm_ioremap(&pdev->dev, res->start,
121 resource_size(res));
122 if (!uart.port.membase)
123 return -ENOMEM;
124
125 data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
126 if (!data)
127 return -ENOMEM;
128
129 data->clk_uart = devm_clk_get(&pdev->dev, "uartclk");
130 if (IS_ERR(data->clk_uart)) {
131 dev_err(&pdev->dev, "uart clock not found\n");
132 return PTR_ERR(data->clk_uart);
133 }
134
135 data->clk_reg = devm_clk_get(&pdev->dev, "reg");
136 if (IS_ERR(data->clk_reg)) {
137 dev_err(&pdev->dev, "reg clock not found\n");
138 return PTR_ERR(data->clk_reg);
139 }
140
141 ret = clk_prepare_enable(data->clk_reg);
142 if (ret) {
143 dev_err(&pdev->dev, "unable to enable reg clock\n");
144 return ret;
145 }
146
147 ret = clk_prepare_enable(data->clk_uart);
148 if (ret) {
149 dev_err(&pdev->dev, "unable to enable uart clock\n");
150 goto dis_clk_reg;
151 }
152
153 ret = of_alias_get_id(pdev->dev.of_node, "serial");
154 if (ret >= 0)
155 uart.port.line = ret;
156
157 data->dma.rx_param = data;
158 data->dma.tx_param = data;
159
160 spin_lock_init(&uart.port.lock);
161 uart.port.dev = &pdev->dev;
162 uart.port.irq = irq;
163 uart.port.iotype = UPIO_MEM32;
164 uart.port.mapbase = res->start;
165 uart.port.regshift = 2;
166 uart.port.type = PORT_16550A;
167 uart.port.flags = UPF_FIXED_PORT | UPF_FIXED_TYPE | UPF_SKIP_TEST;
168 uart.port.uartclk = clk_get_rate(data->clk_uart);
169 uart.port.private_data = data;
170 uart.port.rs485_config = lpc18xx_rs485_config;
171 uart.port.serial_out = lpc18xx_uart_serial_out;
172
173 uart.dma = &data->dma;
174 uart.dma->rxconf.src_maxburst = 1;
175 uart.dma->txconf.dst_maxburst = 1;
176
177 ret = serial8250_register_8250_port(&uart);
178 if (ret < 0) {
179 dev_err(&pdev->dev, "unable to register 8250 port\n");
180 goto dis_uart_clk;
181 }
182
183 data->line = ret;
184 platform_set_drvdata(pdev, data);
185
186 return 0;
187
188 dis_uart_clk:
189 clk_disable_unprepare(data->clk_uart);
190 dis_clk_reg:
191 clk_disable_unprepare(data->clk_reg);
192 return ret;
193 }
194
195 static int lpc18xx_serial_remove(struct platform_device *pdev)
196 {
197 struct lpc18xx_uart_data *data = platform_get_drvdata(pdev);
198
199 serial8250_unregister_port(data->line);
200 clk_disable_unprepare(data->clk_uart);
201 clk_disable_unprepare(data->clk_reg);
202
203 return 0;
204 }
205
206 static const struct of_device_id lpc18xx_serial_match[] = {
207 { .compatible = "nxp,lpc1850-uart" },
208 { },
209 };
210 MODULE_DEVICE_TABLE(of, lpc18xx_serial_match);
211
212 static struct platform_driver lpc18xx_serial_driver = {
213 .probe = lpc18xx_serial_probe,
214 .remove = lpc18xx_serial_remove,
215 .driver = {
216 .name = "lpc18xx-uart",
217 .of_match_table = lpc18xx_serial_match,
218 },
219 };
220 module_platform_driver(lpc18xx_serial_driver);
221
222 MODULE_AUTHOR("Joachim Eastwood <manabian@gmail.com>");
223 MODULE_DESCRIPTION("Serial port driver NXP LPC18xx/43xx devices");
224 MODULE_LICENSE("GPL v2");