drivers/scsi/pcmcia/qlogic

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
qlogic_detect
qlogic_probe
qlogic_detach
qlogic_config_check
qlogic_config
qlogic_release
qlogic_resume
   1 /*======================================================================
   2 
   3     A driver for the Qlogic SCSI card
   4 
   5     qlogic_cs.c 1.79 2000/06/12 21:27:26
   6 
   7     The contents of this file are subject to the Mozilla Public
   8     License Version 1.1 (the "License"); you may not use this file
   9     except in compliance with the License. You may obtain a copy of
  10     the License at http://www.mozilla.org/MPL/
  11 
  12     Software distributed under the License is distributed on an "AS
  13     IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or
  14     implied. See the License for the specific language governing
  15     rights and limitations under the License.
  16 
  17     The initial developer of the original code is David A. Hinds
  18     <dahinds@users.sourceforge.net>.  Portions created by David A. Hinds
  19     are Copyright (C) 1999 David A. Hinds.  All Rights Reserved.
  20 
  21     Alternatively, the contents of this file may be used under the
  22     terms of the GNU General Public License version 2 (the "GPL"), in which
  23     case the provisions of the GPL are applicable instead of the
  24     above.  If you wish to allow the use of your version of this file
  25     only under the terms of the GPL and not to allow others to use
  26     your version of this file under the MPL, indicate your decision
  27     by deleting the provisions above and replace them with the notice
  28     and other provisions required by the GPL.  If you do not delete
  29     the provisions above, a recipient may use your version of this
  30     file under either the MPL or the GPL.
  31     
  32 ======================================================================*/
  33 
  34 #include <linux/module.h>
  35 #include <linux/init.h>
  36 #include <linux/kernel.h>
  37 #include <linux/slab.h>
  38 #include <linux/string.h>
  39 #include <linux/ioport.h>
  40 #include <asm/io.h>
  41 #include <scsi/scsi.h>
  42 #include <linux/major.h>
  43 #include <linux/blkdev.h>
  44 #include <scsi/scsi_ioctl.h>
  45 #include <linux/interrupt.h>
  46 
  47 #include "scsi.h"
  48 #include <scsi/scsi_host.h>
  49 #include "../qlogicfas408.h"
  50 
  51 #include <pcmcia/cistpl.h>
  52 #include <pcmcia/ds.h>
  53 #include <pcmcia/ciscode.h>
  54 
  55 /* Set the following to 2 to use normal interrupt (active high/totempole-
  56  * tristate), otherwise use 0 (REQUIRED FOR PCMCIA) for active low, open
  57  * drain
  58  */
  59 #define INT_TYPE        0
  60 
  61 static char qlogic_name[] = "qlogic_cs";
  62 
  63 static struct scsi_host_template qlogicfas_driver_template = {
  64         .module                 = THIS_MODULE,
  65         .name                   = qlogic_name,
  66         .proc_name              = qlogic_name,
  67         .info                   = qlogicfas408_info,
  68         .queuecommand           = qlogicfas408_queuecommand,
  69         .eh_abort_handler       = qlogicfas408_abort,
  70         .eh_host_reset_handler  = qlogicfas408_host_reset,
  71         .bios_param             = qlogicfas408_biosparam,
  72         .can_queue              = 1,
  73         .this_id                = -1,
  74         .sg_tablesize           = SG_ALL,
  75         .dma_boundary           = PAGE_SIZE - 1,
  76 };
  77 
  78 /*====================================================================*/
  79 
  80 typedef struct scsi_info_t {
  81         struct pcmcia_device    *p_dev;
  82         struct Scsi_Host *host;
  83         unsigned short manf_id;
  84 } scsi_info_t;
  85 
  86 static void qlogic_release(struct pcmcia_device *link);
  87 static void qlogic_detach(struct pcmcia_device *p_dev);
  88 static int qlogic_config(struct pcmcia_device * link);
  89 
  90 static struct Scsi_Host *qlogic_detect(struct scsi_host_template *host,
  91                                 struct pcmcia_device *link, int qbase, int qlirq)
  92 {
  93         int qltyp;              /* type of chip */
  94         int qinitid;
  95         struct Scsi_Host *shost;        /* registered host structure */
  96         struct qlogicfas408_priv *priv;
  97 
  98         qltyp = qlogicfas408_get_chip_type(qbase, INT_TYPE);
  99         qinitid = host->this_id;
 100         if (qinitid < 0)
 101                 qinitid = 7;    /* if no ID, use 7 */
 102 
 103         qlogicfas408_setup(qbase, qinitid, INT_TYPE);
 104 
 105         host->name = qlogic_name;
 106         shost = scsi_host_alloc(host, sizeof(struct qlogicfas408_priv));
 107         if (!shost)
 108                 goto err;
 109         shost->io_port = qbase;
 110         shost->n_io_port = 16;
 111         shost->dma_channel = -1;
 112         if (qlirq != -1)
 113                 shost->irq = qlirq;
 114 
 115         priv = get_priv_by_host(shost);
 116         priv->qlirq = qlirq;
 117         priv->qbase = qbase;
 118         priv->qinitid = qinitid;
 119         priv->shost = shost;
 120         priv->int_type = INT_TYPE;                                      
 121 
 122         if (request_irq(qlirq, qlogicfas408_ihandl, 0, qlogic_name, shost))
 123                 goto free_scsi_host;
 124 
 125         sprintf(priv->qinfo,
 126                 "Qlogicfas Driver version 0.46, chip %02X at %03X, IRQ %d, TPdma:%d",
 127                 qltyp, qbase, qlirq, QL_TURBO_PDMA);
 128 
 129         if (scsi_add_host(shost, NULL))
 130                 goto free_interrupt;
 131 
 132         scsi_scan_host(shost);
 133 
 134         return shost;
 135 
 136 free_interrupt:
 137         free_irq(qlirq, shost);
 138 
 139 free_scsi_host:
 140         scsi_host_put(shost);
 141         
 142 err:
 143         return NULL;
 144 }
 145 static int qlogic_probe(struct pcmcia_device *link)
 146 {
 147         scsi_info_t *info;
 148 
 149         dev_dbg(&link->dev, "qlogic_attach()\n");
 150 
 151         /* Create new SCSI device */
 152         info = kzalloc(sizeof(*info), GFP_KERNEL);
 153         if (!info)
 154                 return -ENOMEM;
 155         info->p_dev = link;
 156         link->priv = info;
 157         link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO;
 158         link->config_regs = PRESENT_OPTION;
 159 
 160         return qlogic_config(link);
 161 }                               /* qlogic_attach */
 162 
 163 /*====================================================================*/
 164 
 165 static void qlogic_detach(struct pcmcia_device *link)
 166 {
 167         dev_dbg(&link->dev, "qlogic_detach\n");
 168 
 169         qlogic_release(link);
 170         kfree(link->priv);
 171 
 172 }                               /* qlogic_detach */
 173 
 174 /*====================================================================*/
 175 
 176 static int qlogic_config_check(struct pcmcia_device *p_dev, void *priv_data)
 177 {
 178         p_dev->io_lines = 10;
 179         p_dev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
 180         p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO;
 181 
 182         if (p_dev->resource[0]->start == 0)
 183                 return -ENODEV;
 184 
 185         return pcmcia_request_io(p_dev);
 186 }
 187 
 188 static int qlogic_config(struct pcmcia_device * link)
 189 {
 190         scsi_info_t *info = link->priv;
 191         int ret;
 192         struct Scsi_Host *host;
 193 
 194         dev_dbg(&link->dev, "qlogic_config\n");
 195 
 196         ret = pcmcia_loop_config(link, qlogic_config_check, NULL);
 197         if (ret)
 198                 goto failed;
 199 
 200         if (!link->irq)
 201                 goto failed;
 202 
 203         ret = pcmcia_enable_device(link);
 204         if (ret)
 205                 goto failed;
 206 
 207         if ((info->manf_id == MANFID_MACNICA) || (info->manf_id == MANFID_PIONEER) || (info->manf_id == 0x0098)) {
 208                 /* set ATAcmd */
 209                 outb(0xb4, link->resource[0]->start + 0xd);
 210                 outb(0x24, link->resource[0]->start + 0x9);
 211                 outb(0x04, link->resource[0]->start + 0xd);
 212         }
 213 
 214         /* The KXL-810AN has a bigger IO port window */
 215         if (resource_size(link->resource[0]) == 32)
 216                 host = qlogic_detect(&qlogicfas_driver_template, link,
 217                         link->resource[0]->start + 16, link->irq);
 218         else
 219                 host = qlogic_detect(&qlogicfas_driver_template, link,
 220                         link->resource[0]->start, link->irq);
 221         
 222         if (!host) {
 223                 printk(KERN_INFO "%s: no SCSI devices found\n", qlogic_name);
 224                 goto failed;
 225         }
 226 
 227         info->host = host;
 228 
 229         return 0;
 230 
 231 failed:
 232         pcmcia_disable_device(link);
 233         return -ENODEV;
 234 }                               /* qlogic_config */
 235 
 236 /*====================================================================*/
 237 
 238 static void qlogic_release(struct pcmcia_device *link)
 239 {
 240         scsi_info_t *info = link->priv;
 241 
 242         dev_dbg(&link->dev, "qlogic_release\n");
 243 
 244         scsi_remove_host(info->host);
 245 
 246         free_irq(link->irq, info->host);
 247         pcmcia_disable_device(link);
 248 
 249         scsi_host_put(info->host);
 250 }
 251 
 252 /*====================================================================*/
 253 
 254 static int qlogic_resume(struct pcmcia_device *link)
 255 {
 256         scsi_info_t *info = link->priv;
 257         int ret;
 258 
 259         ret = pcmcia_enable_device(link);
 260         if (ret)
 261                 return ret;
 262 
 263         if ((info->manf_id == MANFID_MACNICA) ||
 264             (info->manf_id == MANFID_PIONEER) ||
 265             (info->manf_id == 0x0098)) {
 266                 outb(0x80, link->resource[0]->start + 0xd);
 267                 outb(0x24, link->resource[0]->start + 0x9);
 268                 outb(0x04, link->resource[0]->start + 0xd);
 269         }
 270         /* Ugggglllyyyy!!! */
 271         qlogicfas408_host_reset(NULL);
 272 
 273         return 0;
 274 }
 275 
 276 static const struct pcmcia_device_id qlogic_ids[] = {
 277         PCMCIA_DEVICE_PROD_ID12("EIger Labs", "PCMCIA-to-SCSI Adapter", 0x88395fa7, 0x33b7a5e6),
 278         PCMCIA_DEVICE_PROD_ID12("EPSON", "SCSI-2 PC Card SC200", 0xd361772f, 0x299d1751),
 279         PCMCIA_DEVICE_PROD_ID12("MACNICA", "MIRACLE SCSI-II mPS110", 0x20841b68, 0xab3c3b6d),
 280         PCMCIA_DEVICE_PROD_ID12("MIDORI ELECTRONICS ", "CN-SC43", 0x6534382a, 0xd67eee79),
 281         PCMCIA_DEVICE_PROD_ID12("NEC", "PC-9801N-J03R", 0x18df0ba0, 0x24662e8a),
 282         PCMCIA_DEVICE_PROD_ID12("KME ", "KXLC003", 0x82375a27, 0xf68e5bf7),
 283         PCMCIA_DEVICE_PROD_ID12("KME ", "KXLC004", 0x82375a27, 0x68eace54),
 284         PCMCIA_DEVICE_PROD_ID12("KME", "KXLC101", 0x3faee676, 0x194250ec),
 285         PCMCIA_DEVICE_PROD_ID12("QLOGIC CORPORATION", "pc05", 0xd77b2930, 0xa85b2735),
 286         PCMCIA_DEVICE_PROD_ID12("QLOGIC CORPORATION", "pc05 rev 1.10", 0xd77b2930, 0x70f8b5f8),
 287         PCMCIA_DEVICE_PROD_ID123("KME", "KXLC002", "00", 0x3faee676, 0x81896b61, 0xf99f065f),
 288         PCMCIA_DEVICE_PROD_ID12("RATOC System Inc.", "SCSI2 CARD 37", 0x85c10e17, 0x1a2640c1),
 289         PCMCIA_DEVICE_PROD_ID12("TOSHIBA", "SCSC200A PC CARD SCSI", 0xb4585a1a, 0xa6f06ebe),
 290         PCMCIA_DEVICE_PROD_ID12("TOSHIBA", "SCSC200B PC CARD SCSI-10", 0xb4585a1a, 0x0a88dea0),
 291         /* these conflict with other cards! */
 292         /* PCMCIA_DEVICE_PROD_ID123("MACNICA", "MIRACLE SCSI", "mPS100", 0x20841b68, 0xf8dedaeb, 0x89f7fafb), */
 293         /* PCMCIA_DEVICE_PROD_ID123("MACNICA", "MIRACLE SCSI", "mPS100", 0x20841b68, 0xf8dedaeb, 0x89f7fafb), */
 294         PCMCIA_DEVICE_NULL,
 295 };
 296 MODULE_DEVICE_TABLE(pcmcia, qlogic_ids);
 297 
 298 static struct pcmcia_driver qlogic_cs_driver = {
 299         .owner          = THIS_MODULE,
 300         .name           = "qlogic_cs",
 301         .probe          = qlogic_probe,
 302         .remove         = qlogic_detach,
 303         .id_table       = qlogic_ids,
 304         .resume         = qlogic_resume,
 305 };
 306 
 307 MODULE_AUTHOR("Tom Zerucha, Michael Griffith");
 308 MODULE_DESCRIPTION("Driver for the PCMCIA Qlogic FAS SCSI controllers");
 309 MODULE_LICENSE("GPL");
 310 module_pcmcia_driver(qlogic_cs_driver);
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/scsi/pcmcia/qlogic_stub.c

DEFINITIONS
