drivers/scsi/mac53c94.h

/* [<][>][^][v][top][bottom][index][help] */
   1 /* SPDX-License-Identifier: GPL-2.0 */
   2 /*
   3  * mac53c94.h: definitions for the driver for the 53c94 SCSI bus adaptor
   4  * found on Power Macintosh computers, controlling the external SCSI chain.
   5  *
   6  * Copyright (C) 1996 Paul Mackerras.
   7  */
   8 #ifndef _MAC53C94_H
   9 #define _MAC53C94_H
  10 
  11 /*
  12  * Registers in the 53C94 controller.
  13  */
  14 
  15 struct mac53c94_regs {
  16         unsigned char   count_lo;
  17         char pad0[15];
  18         unsigned char   count_mid;
  19         char pad1[15];
  20         unsigned char   fifo;
  21         char pad2[15];
  22         unsigned char   command;
  23         char pad3[15];
  24         unsigned char   status;
  25         char pad4[15];
  26         unsigned char   interrupt;
  27         char pad5[15];
  28         unsigned char   seqstep;
  29         char pad6[15];
  30         unsigned char   flags;
  31         char pad7[15];
  32         unsigned char   config1;
  33         char pad8[15];
  34         unsigned char   clk_factor;
  35         char pad9[15];
  36         unsigned char   test;
  37         char pad10[15];
  38         unsigned char   config2;
  39         char pad11[15];
  40         unsigned char   config3;
  41         char pad12[15];
  42         unsigned char   config4;
  43         char pad13[15];
  44         unsigned char   count_hi;
  45         char pad14[15];
  46         unsigned char   fifo_res;
  47         char pad15[15];
  48 };
  49 
  50 /*
  51  * Alternate functions for some registers.
  52  */
  53 #define dest_id         status
  54 #define sel_timeout     interrupt
  55 #define sync_period     seqstep
  56 #define sync_offset     flags
  57 
  58 /*
  59  * Bits in command register.
  60  */
  61 #define CMD_DMA_MODE    0x80
  62 #define CMD_MODE_MASK   0x70
  63 #define CMD_MODE_INIT   0x10
  64 #define CMD_MODE_TARG   0x20
  65 #define CMD_MODE_DISC   0x40
  66 
  67 #define CMD_NOP         0
  68 #define CMD_FLUSH       1
  69 #define CMD_RESET       2
  70 #define CMD_SCSI_RESET  3
  71 
  72 #define CMD_XFER_DATA   0x10
  73 #define CMD_I_COMPLETE  0x11
  74 #define CMD_ACCEPT_MSG  0x12
  75 #define CMD_XFER_PAD    0x18
  76 #define CMD_SET_ATN     0x1a
  77 #define CMD_CLR_ATN     0x1b
  78 
  79 #define CMD_SEND_MSG    0x20
  80 #define CMD_SEND_STATUS 0x21
  81 #define CMD_SEND_DATA   0x22
  82 #define CMD_DISC_SEQ    0x23
  83 #define CMD_TERMINATE   0x24
  84 #define CMD_T_COMPLETE  0x25
  85 #define CMD_DISCONNECT  0x27
  86 #define CMD_RECV_MSG    0x28
  87 #define CMD_RECV_CDB    0x29
  88 #define CMD_RECV_DATA   0x2a
  89 #define CMD_RECV_CMD    0x2b
  90 #define CMD_ABORT_DMA   0x04
  91 
  92 #define CMD_RESELECT    0x40
  93 #define CMD_SELECT      0x41
  94 #define CMD_SELECT_ATN  0x42
  95 #define CMD_SELATN_STOP 0x43
  96 #define CMD_ENABLE_SEL  0x44
  97 #define CMD_DISABLE_SEL 0x45
  98 #define CMD_SEL_ATN3    0x46
  99 #define CMD_RESEL_ATN3  0x47
 100 
 101 /*
 102  * Bits in status register.
 103  */
 104 #define STAT_IRQ        0x80
 105 #define STAT_ERROR      0x40
 106 #define STAT_PARITY     0x20
 107 #define STAT_TC_ZERO    0x10
 108 #define STAT_DONE       0x08
 109 #define STAT_PHASE      0x07
 110 #define STAT_MSG        0x04
 111 #define STAT_CD         0x02
 112 #define STAT_IO         0x01
 113 
 114 /*
 115  * Bits in interrupt register.
 116  */
 117 #define INTR_RESET      0x80    /* SCSI bus was reset */
 118 #define INTR_ILL_CMD    0x40    /* illegal command */
 119 #define INTR_DISCONNECT 0x20    /* we got disconnected */
 120 #define INTR_BUS_SERV   0x10    /* bus service requested */
 121 #define INTR_DONE       0x08    /* function completed */
 122 #define INTR_RESELECTED 0x04    /* we were reselected */
 123 #define INTR_SEL_ATN    0x02    /* we were selected, ATN asserted */
 124 #define INTR_SELECT     0x01    /* we were selected, ATN negated */
 125 
 126 /*
 127  * Encoding for the select timeout.
 128  */
 129 #define TIMO_VAL(x)     ((x) * 5000 / 7682)
 130 
 131 /*
 132  * Bits in sequence step register.
 133  */
 134 #define SS_MASK         7
 135 #define SS_ARB_SEL      0       /* Selection & arbitration complete */
 136 #define SS_MSG_SENT     1       /* One message byte sent */
 137 #define SS_NOT_CMD      2       /* Not in command phase */
 138 #define SS_PHASE_CHG    3       /* Early phase change, cmd bytes lost */
 139 #define SS_DONE         4       /* Command was sent OK */
 140 
 141 /*
 142  * Encoding for sync transfer period.
 143  */
 144 #define SYNCP_MASK      0x1f
 145 #define SYNCP_MIN       4
 146 #define SYNCP_MAX       31
 147 
 148 /*
 149  * Bits in flags register.
 150  */
 151 #define FLAGS_FIFO_LEV  0x1f
 152 #define FLAGS_SEQ_STEP  0xe0
 153 
 154 /*
 155  * Encoding for sync offset.
 156  */
 157 #define SYNCO_MASK      0x0f
 158 #define SYNCO_ASS_CTRL  0x30    /* REQ/ACK assertion control */
 159 #define SYNCO_NEG_CTRL  0xc0    /* REQ/ACK negation control */
 160 
 161 /*
 162  * Bits in config1 register.
 163  */
 164 #define CF1_SLOW_CABLE  0x80    /* Slow cable mode */
 165 #define CF1_NO_RES_REP  0x40    /* Disable SCSI reset reports */
 166 #define CF1_PAR_TEST    0x20    /* Parity test mode enable */
 167 #define CF1_PAR_ENABLE  0x10    /* Enable parity checks */
 168 #define CF1_TEST        0x08    /* Chip tests */
 169 #define CF1_MY_ID       0x07    /* Controller's address on bus */
 170 
 171 /*
 172  * Encoding for clk_factor register.
 173  */
 174 #define CLKF_MASK       7
 175 #define CLKF_VAL(freq)  ((((freq) + 4999999) / 5000000) & CLKF_MASK)
 176 
 177 /*
 178  * Bits in test mode register.
 179  */
 180 #define TEST_TARGET     1       /* target test mode */
 181 #define TEST_INITIATOR  2       /* initiator test mode */
 182 #define TEST_TRISTATE   4       /* tristate (hi-z) test mode */
 183 
 184 /*
 185  * Bits in config2 register.
 186  */
 187 #define CF2_RFB         0x80
 188 #define CF2_FEATURE_EN  0x40    /* enable features / phase latch */
 189 #define CF2_BYTECTRL    0x20
 190 #define CF2_DREQ_HIZ    0x10
 191 #define CF2_SCSI2       0x08
 192 #define CF2_PAR_ABORT   0x04    /* bad parity target abort */
 193 #define CF2_REG_PARERR  0x02    /* register parity error */
 194 #define CF2_DMA_PARERR  0x01    /* DMA parity error */
 195 
 196 /*
 197  * Bits in the config3 register.
 198  */
 199 #define CF3_ID_MSG_CHK  0x80
 200 #define CF3_3B_MSGS     0x40
 201 #define CF3_CDB10       0x20
 202 #define CF3_FASTSCSI    0x10    /* enable fast SCSI support */
 203 #define CF3_FASTCLOCK   0x08
 204 #define CF3_SAVERESID   0x04
 205 #define CF3_ALT_DMA     0x02
 206 #define CF3_THRESH_8    0x01
 207 
 208 /*
 209  * Bits in the config4 register.
 210  */
 211 #define CF4_EAN         0x04
 212 #define CF4_TEST        0x02
 213 #define CF4_BBTE        0x01
 214 
 215 #endif /* _MAC53C94_H */
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/scsi/mac53c94.h

INCLUDED FROM
