root/drivers/net/wireless/intel/iwlwifi/fw/api/tx.h

/* [<][>][^][v][top][bottom][index][help] */

INCLUDED FROM


   1 /******************************************************************************
   2  *
   3  * This file is provided under a dual BSD/GPLv2 license.  When using or
   4  * redistributing this file, you may do so under either license.
   5  *
   6  * GPL LICENSE SUMMARY
   7  *
   8  * Copyright(c) 2012 - 2014 Intel Corporation. All rights reserved.
   9  * Copyright(c) 2016 - 2017 Intel Deutschland GmbH
  10  * Copyright(c) 2018 Intel Corporation
  11  *
  12  * This program is free software; you can redistribute it and/or modify
  13  * it under the terms of version 2 of the GNU General Public License as
  14  * published by the Free Software Foundation.
  15  *
  16  * This program is distributed in the hope that it will be useful, but
  17  * WITHOUT ANY WARRANTY; without even the implied warranty of
  18  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
  19  * General Public License for more details.
  20  *
  21  * The full GNU General Public License is included in this distribution
  22  * in the file called COPYING.
  23  *
  24  * Contact Information:
  25  *  Intel Linux Wireless <linuxwifi@intel.com>
  26  * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
  27  *
  28  * BSD LICENSE
  29  *
  30  * Copyright(c) 2012 - 2014 Intel Corporation. All rights reserved.
  31  * Copyright(c) 2016 - 2017 Intel Deutschland GmbH
  32  * Copyright(c) 2018 Intel Corporation
  33  * All rights reserved.
  34  *
  35  * Redistribution and use in source and binary forms, with or without
  36  * modification, are permitted provided that the following conditions
  37  * are met:
  38  *
  39  *  * Redistributions of source code must retain the above copyright
  40  *    notice, this list of conditions and the following disclaimer.
  41  *  * Redistributions in binary form must reproduce the above copyright
  42  *    notice, this list of conditions and the following disclaimer in
  43  *    the documentation and/or other materials provided with the
  44  *    distribution.
  45  *  * Neither the name Intel Corporation nor the names of its
  46  *    contributors may be used to endorse or promote products derived
  47  *    from this software without specific prior written permission.
  48  *
  49  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
  50  * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
  51  * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
  52  * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
  53  * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
  54  * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
  55  * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
  56  * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
  57  * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
  58  * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
  59  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  60  *****************************************************************************/
  61 
  62 #ifndef __iwl_fw_api_tx_h__
  63 #define __iwl_fw_api_tx_h__
  64 
  65 /**
  66  * enum iwl_tx_flags - bitmasks for tx_flags in TX command
  67  * @TX_CMD_FLG_PROT_REQUIRE: use RTS or CTS-to-self to protect the frame
  68  * @TX_CMD_FLG_WRITE_TX_POWER: update current tx power value in the mgmt frame
  69  * @TX_CMD_FLG_ACK: expect ACK from receiving station
  70  * @TX_CMD_FLG_STA_RATE: use RS table with initial index from the TX command.
  71  *      Otherwise, use rate_n_flags from the TX command
  72  * @TX_CMD_FLG_BAR: this frame is a BA request, immediate BAR is expected
  73  *      Must set TX_CMD_FLG_ACK with this flag.
  74  * @TX_CMD_FLG_TXOP_PROT: TXOP protection requested
  75  * @TX_CMD_FLG_VHT_NDPA: mark frame is NDPA for VHT beamformer sequence
  76  * @TX_CMD_FLG_HT_NDPA: mark frame is NDPA for HT beamformer sequence
  77  * @TX_CMD_FLG_CSI_FDBK2HOST: mark to send feedback to host (only if good CRC)
  78  * @TX_CMD_FLG_BT_PRIO_POS: the position of the BT priority (bit 11 is ignored
  79  *      on old firmwares).
  80  * @TX_CMD_FLG_BT_DIS: disable BT priority for this frame
  81  * @TX_CMD_FLG_SEQ_CTL: set if FW should override the sequence control.
  82  *      Should be set for mgmt, non-QOS data, mcast, bcast and in scan command
  83  * @TX_CMD_FLG_MORE_FRAG: this frame is non-last MPDU
  84  * @TX_CMD_FLG_TSF: FW should calculate and insert TSF in the frame
  85  *      Should be set for beacons and probe responses
  86  * @TX_CMD_FLG_CALIB: activate PA TX power calibrations
  87  * @TX_CMD_FLG_KEEP_SEQ_CTL: if seq_ctl is set, don't increase inner seq count
  88  * @TX_CMD_FLG_MH_PAD: driver inserted 2 byte padding after MAC header.
  89  *      Should be set for 26/30 length MAC headers
  90  * @TX_CMD_FLG_RESP_TO_DRV: zero this if the response should go only to FW
  91  * @TX_CMD_FLG_TKIP_MIC_DONE: FW already performed TKIP MIC calculation
  92  * @TX_CMD_FLG_DUR: disable duration overwriting used in PS-Poll Assoc-id
  93  * @TX_CMD_FLG_FW_DROP: FW should mark frame to be dropped
  94  * @TX_CMD_FLG_EXEC_PAPD: execute PAPD
  95  * @TX_CMD_FLG_PAPD_TYPE: 0 for reference power, 1 for nominal power
  96  * @TX_CMD_FLG_HCCA_CHUNK: mark start of TSPEC chunk
  97  */
  98 enum iwl_tx_flags {
  99         TX_CMD_FLG_PROT_REQUIRE         = BIT(0),
 100         TX_CMD_FLG_WRITE_TX_POWER       = BIT(1),
 101         TX_CMD_FLG_ACK                  = BIT(3),
 102         TX_CMD_FLG_STA_RATE             = BIT(4),
 103         TX_CMD_FLG_BAR                  = BIT(6),
 104         TX_CMD_FLG_TXOP_PROT            = BIT(7),
 105         TX_CMD_FLG_VHT_NDPA             = BIT(8),
 106         TX_CMD_FLG_HT_NDPA              = BIT(9),
 107         TX_CMD_FLG_CSI_FDBK2HOST        = BIT(10),
 108         TX_CMD_FLG_BT_PRIO_POS          = 11,
 109         TX_CMD_FLG_BT_DIS               = BIT(12),
 110         TX_CMD_FLG_SEQ_CTL              = BIT(13),
 111         TX_CMD_FLG_MORE_FRAG            = BIT(14),
 112         TX_CMD_FLG_TSF                  = BIT(16),
 113         TX_CMD_FLG_CALIB                = BIT(17),
 114         TX_CMD_FLG_KEEP_SEQ_CTL         = BIT(18),
 115         TX_CMD_FLG_MH_PAD               = BIT(20),
 116         TX_CMD_FLG_RESP_TO_DRV          = BIT(21),
 117         TX_CMD_FLG_TKIP_MIC_DONE        = BIT(23),
 118         TX_CMD_FLG_DUR                  = BIT(25),
 119         TX_CMD_FLG_FW_DROP              = BIT(26),
 120         TX_CMD_FLG_EXEC_PAPD            = BIT(27),
 121         TX_CMD_FLG_PAPD_TYPE            = BIT(28),
 122         TX_CMD_FLG_HCCA_CHUNK           = BIT(31)
 123 }; /* TX_FLAGS_BITS_API_S_VER_1 */
 124 
 125 /**
 126  * enum iwl_tx_cmd_flags - bitmasks for tx_flags in TX command for 22000
 127  * @IWL_TX_FLAGS_CMD_RATE: use rate from the TX command
 128  * @IWL_TX_FLAGS_ENCRYPT_DIS: frame should not be encrypted, even if it belongs
 129  *      to a secured STA
 130  * @IWL_TX_FLAGS_HIGH_PRI: high priority frame (like EAPOL) - can affect rate
 131  *      selection, retry limits and BT kill
 132  */
 133 enum iwl_tx_cmd_flags {
 134         IWL_TX_FLAGS_CMD_RATE           = BIT(0),
 135         IWL_TX_FLAGS_ENCRYPT_DIS        = BIT(1),
 136         IWL_TX_FLAGS_HIGH_PRI           = BIT(2),
 137 }; /* TX_FLAGS_BITS_API_S_VER_3 */
 138 
 139 /**
 140  * enum iwl_tx_pm_timeouts - pm timeout values in TX command
 141  * @PM_FRAME_NONE: no need to suspend sleep mode
 142  * @PM_FRAME_MGMT: fw suspend sleep mode for 100TU
 143  * @PM_FRAME_ASSOC: fw suspend sleep mode for 10sec
 144  */
 145 enum iwl_tx_pm_timeouts {
 146         PM_FRAME_NONE           = 0,
 147         PM_FRAME_MGMT           = 2,
 148         PM_FRAME_ASSOC          = 3,
 149 };
 150 
 151 #define TX_CMD_SEC_MSK                  0x07
 152 #define TX_CMD_SEC_WEP_KEY_IDX_POS      6
 153 #define TX_CMD_SEC_WEP_KEY_IDX_MSK      0xc0
 154 
 155 /**
 156  * enum iwl_tx_cmd_sec_ctrl - bitmasks for security control in TX command
 157  * @TX_CMD_SEC_WEP: WEP encryption algorithm.
 158  * @TX_CMD_SEC_CCM: CCM encryption algorithm.
 159  * @TX_CMD_SEC_TKIP: TKIP encryption algorithm.
 160  * @TX_CMD_SEC_EXT: extended cipher algorithm.
 161  * @TX_CMD_SEC_GCMP: GCMP encryption algorithm.
 162  * @TX_CMD_SEC_KEY128: set for 104 bits WEP key.
 163  * @TX_CMD_SEC_KEY_FROM_TABLE: for a non-WEP key, set if the key should be taken
 164  *      from the table instead of from the TX command.
 165  *      If the key is taken from the key table its index should be given by the
 166  *      first byte of the TX command key field.
 167  */
 168 enum iwl_tx_cmd_sec_ctrl {
 169         TX_CMD_SEC_WEP                  = 0x01,
 170         TX_CMD_SEC_CCM                  = 0x02,
 171         TX_CMD_SEC_TKIP                 = 0x03,
 172         TX_CMD_SEC_EXT                  = 0x04,
 173         TX_CMD_SEC_GCMP                 = 0x05,
 174         TX_CMD_SEC_KEY128               = 0x08,
 175         TX_CMD_SEC_KEY_FROM_TABLE       = 0x10,
 176 };
 177 
 178 /*
 179  * TX command Frame life time in us - to be written in pm_frame_timeout
 180  */
 181 #define TX_CMD_LIFE_TIME_INFINITE       0xFFFFFFFF
 182 #define TX_CMD_LIFE_TIME_DEFAULT        2000000 /* 2000 ms*/
 183 #define TX_CMD_LIFE_TIME_PROBE_RESP     40000 /* 40 ms */
 184 #define TX_CMD_LIFE_TIME_EXPIRED_FRAME  0
 185 
 186 /*
 187  * TID for non QoS frames - to be written in tid_tspec
 188  */
 189 #define IWL_TID_NON_QOS 0
 190 
 191 /*
 192  * Limits on the retransmissions - to be written in {data,rts}_retry_limit
 193  */
 194 #define IWL_DEFAULT_TX_RETRY                    15
 195 #define IWL_MGMT_DFAULT_RETRY_LIMIT             3
 196 #define IWL_RTS_DFAULT_RETRY_LIMIT              60
 197 #define IWL_BAR_DFAULT_RETRY_LIMIT              60
 198 #define IWL_LOW_RETRY_LIMIT                     7
 199 
 200 /**
 201  * enum iwl_tx_offload_assist_flags_pos -  set %iwl_tx_cmd offload_assist values
 202  * @TX_CMD_OFFLD_IP_HDR: offset to start of IP header (in words)
 203  *      from mac header end. For normal case it is 4 words for SNAP.
 204  *      note: tx_cmd, mac header and pad are not counted in the offset.
 205  *      This is used to help the offload in case there is tunneling such as
 206  *      IPv6 in IPv4, in such case the ip header offset should point to the
 207  *      inner ip header and IPv4 checksum of the external header should be
 208  *      calculated by driver.
 209  * @TX_CMD_OFFLD_L4_EN: enable TCP/UDP checksum
 210  * @TX_CMD_OFFLD_L3_EN: enable IP header checksum
 211  * @TX_CMD_OFFLD_MH_SIZE: size of the mac header in words. Includes the IV
 212  *      field. Doesn't include the pad.
 213  * @TX_CMD_OFFLD_PAD: mark 2-byte pad was inserted after the mac header for
 214  *      alignment
 215  * @TX_CMD_OFFLD_AMSDU: mark TX command is A-MSDU
 216  */
 217 enum iwl_tx_offload_assist_flags_pos {
 218         TX_CMD_OFFLD_IP_HDR =           0,
 219         TX_CMD_OFFLD_L4_EN =            6,
 220         TX_CMD_OFFLD_L3_EN =            7,
 221         TX_CMD_OFFLD_MH_SIZE =          8,
 222         TX_CMD_OFFLD_PAD =              13,
 223         TX_CMD_OFFLD_AMSDU =            14,
 224 };
 225 
 226 #define IWL_TX_CMD_OFFLD_MH_MASK        0x1f
 227 #define IWL_TX_CMD_OFFLD_IP_HDR_MASK    0x3f
 228 
 229 /* TODO: complete documentation for try_cnt and btkill_cnt */
 230 /**
 231  * struct iwl_tx_cmd - TX command struct to FW
 232  * ( TX_CMD = 0x1c )
 233  * @len: in bytes of the payload, see below for details
 234  * @offload_assist: TX offload configuration
 235  * @tx_flags: combination of TX_CMD_FLG_*
 236  * @scratch: scratch buffer used by the device
 237  * @rate_n_flags: rate for *all* Tx attempts, if TX_CMD_FLG_STA_RATE_MSK is
 238  *      cleared. Combination of RATE_MCS_*
 239  * @sta_id: index of destination station in FW station table
 240  * @sec_ctl: security control, TX_CMD_SEC_*
 241  * @initial_rate_index: index into the the rate table for initial TX attempt.
 242  *      Applied if TX_CMD_FLG_STA_RATE_MSK is set, normally 0 for data frames.
 243  * @reserved2: reserved
 244  * @key: security key
 245  * @reserved3: reserved
 246  * @life_time: frame life time (usecs??)
 247  * @dram_lsb_ptr: Physical address of scratch area in the command (try_cnt +
 248  *      btkill_cnd + reserved), first 32 bits. "0" disables usage.
 249  * @dram_msb_ptr: upper bits of the scratch physical address
 250  * @rts_retry_limit: max attempts for RTS
 251  * @data_retry_limit: max attempts to send the data packet
 252  * @tid_tspec: TID/tspec
 253  * @pm_frame_timeout: PM TX frame timeout
 254  * @reserved4: reserved
 255  * @payload: payload (same as @hdr)
 256  * @hdr: 802.11 header (same as @payload)
 257  *
 258  * The byte count (both len and next_frame_len) includes MAC header
 259  * (24/26/30/32 bytes)
 260  * + 2 bytes pad if 26/30 header size
 261  * + 8 byte IV for CCM or TKIP (not used for WEP)
 262  * + Data payload
 263  * + 8-byte MIC (not used for CCM/WEP)
 264  * It does not include post-MAC padding, i.e.,
 265  * MIC (CCM) 8 bytes, ICV (WEP/TKIP/CKIP) 4 bytes, CRC 4 bytes.
 266  * Range of len: 14-2342 bytes.
 267  *
 268  * After the struct fields the MAC header is placed, plus any padding,
 269  * and then the actial payload.
 270  */
 271 struct iwl_tx_cmd {
 272         __le16 len;
 273         __le16 offload_assist;
 274         __le32 tx_flags;
 275         struct {
 276                 u8 try_cnt;
 277                 u8 btkill_cnt;
 278                 __le16 reserved;
 279         } scratch; /* DRAM_SCRATCH_API_U_VER_1 */
 280         __le32 rate_n_flags;
 281         u8 sta_id;
 282         u8 sec_ctl;
 283         u8 initial_rate_index;
 284         u8 reserved2;
 285         u8 key[16];
 286         __le32 reserved3;
 287         __le32 life_time;
 288         __le32 dram_lsb_ptr;
 289         u8 dram_msb_ptr;
 290         u8 rts_retry_limit;
 291         u8 data_retry_limit;
 292         u8 tid_tspec;
 293         __le16 pm_frame_timeout;
 294         __le16 reserved4;
 295         u8 payload[0];
 296         struct ieee80211_hdr hdr[0];
 297 } __packed; /* TX_CMD_API_S_VER_6 */
 298 
 299 struct iwl_dram_sec_info {
 300         __le32 pn_low;
 301         __le16 pn_high;
 302         __le16 aux_info;
 303 } __packed; /* DRAM_SEC_INFO_API_S_VER_1 */
 304 
 305 /**
 306  * struct iwl_tx_cmd_gen2 - TX command struct to FW for 22000 devices
 307  * ( TX_CMD = 0x1c )
 308  * @len: in bytes of the payload, see below for details
 309  * @offload_assist: TX offload configuration
 310  * @flags: combination of &enum iwl_tx_cmd_flags
 311  * @dram_info: FW internal DRAM storage
 312  * @rate_n_flags: rate for *all* Tx attempts, if TX_CMD_FLG_STA_RATE_MSK is
 313  *      cleared. Combination of RATE_MCS_*
 314  * @hdr: 802.11 header
 315  */
 316 struct iwl_tx_cmd_gen2 {
 317         __le16 len;
 318         __le16 offload_assist;
 319         __le32 flags;
 320         struct iwl_dram_sec_info dram_info;
 321         __le32 rate_n_flags;
 322         struct ieee80211_hdr hdr[0];
 323 } __packed; /* TX_CMD_API_S_VER_7 */
 324 
 325 /**
 326  * struct iwl_tx_cmd_gen3 - TX command struct to FW for 22560 devices
 327  * ( TX_CMD = 0x1c )
 328  * @len: in bytes of the payload, see below for details
 329  * @flags: combination of &enum iwl_tx_cmd_flags
 330  * @offload_assist: TX offload configuration
 331  * @dram_info: FW internal DRAM storage
 332  * @rate_n_flags: rate for *all* Tx attempts, if TX_CMD_FLG_STA_RATE_MSK is
 333  *      cleared. Combination of RATE_MCS_*
 334  * @ttl: time to live - packet lifetime limit. The FW should drop if
 335  *      passed.
 336  * @hdr: 802.11 header
 337  */
 338 struct iwl_tx_cmd_gen3 {
 339         __le16 len;
 340         __le16 flags;
 341         __le32 offload_assist;
 342         struct iwl_dram_sec_info dram_info;
 343         __le32 rate_n_flags;
 344         __le64 ttl;
 345         struct ieee80211_hdr hdr[0];
 346 } __packed; /* TX_CMD_API_S_VER_8 */
 347 
 348 /*
 349  * TX response related data
 350  */
 351 
 352 /*
 353  * enum iwl_tx_status - status that is returned by the fw after attempts to Tx
 354  * @TX_STATUS_SUCCESS:
 355  * @TX_STATUS_DIRECT_DONE:
 356  * @TX_STATUS_POSTPONE_DELAY:
 357  * @TX_STATUS_POSTPONE_FEW_BYTES:
 358  * @TX_STATUS_POSTPONE_BT_PRIO:
 359  * @TX_STATUS_POSTPONE_QUIET_PERIOD:
 360  * @TX_STATUS_POSTPONE_CALC_TTAK:
 361  * @TX_STATUS_FAIL_INTERNAL_CROSSED_RETRY:
 362  * @TX_STATUS_FAIL_SHORT_LIMIT:
 363  * @TX_STATUS_FAIL_LONG_LIMIT:
 364  * @TX_STATUS_FAIL_UNDERRUN:
 365  * @TX_STATUS_FAIL_DRAIN_FLOW:
 366  * @TX_STATUS_FAIL_RFKILL_FLUSH:
 367  * @TX_STATUS_FAIL_LIFE_EXPIRE:
 368  * @TX_STATUS_FAIL_DEST_PS:
 369  * @TX_STATUS_FAIL_HOST_ABORTED:
 370  * @TX_STATUS_FAIL_BT_RETRY:
 371  * @TX_STATUS_FAIL_STA_INVALID:
 372  * @TX_TATUS_FAIL_FRAG_DROPPED:
 373  * @TX_STATUS_FAIL_TID_DISABLE:
 374  * @TX_STATUS_FAIL_FIFO_FLUSHED:
 375  * @TX_STATUS_FAIL_SMALL_CF_POLL:
 376  * @TX_STATUS_FAIL_FW_DROP:
 377  * @TX_STATUS_FAIL_STA_COLOR_MISMATCH: mismatch between color of Tx cmd and
 378  *      STA table
 379  * @TX_FRAME_STATUS_INTERNAL_ABORT:
 380  * @TX_MODE_MSK:
 381  * @TX_MODE_NO_BURST:
 382  * @TX_MODE_IN_BURST_SEQ:
 383  * @TX_MODE_FIRST_IN_BURST:
 384  * @TX_QUEUE_NUM_MSK:
 385  *
 386  * Valid only if frame_count =1
 387  * TODO: complete documentation
 388  */
 389 enum iwl_tx_status {
 390         TX_STATUS_MSK = 0x000000ff,
 391         TX_STATUS_SUCCESS = 0x01,
 392         TX_STATUS_DIRECT_DONE = 0x02,
 393         /* postpone TX */
 394         TX_STATUS_POSTPONE_DELAY = 0x40,
 395         TX_STATUS_POSTPONE_FEW_BYTES = 0x41,
 396         TX_STATUS_POSTPONE_BT_PRIO = 0x42,
 397         TX_STATUS_POSTPONE_QUIET_PERIOD = 0x43,
 398         TX_STATUS_POSTPONE_CALC_TTAK = 0x44,
 399         /* abort TX */
 400         TX_STATUS_FAIL_INTERNAL_CROSSED_RETRY = 0x81,
 401         TX_STATUS_FAIL_SHORT_LIMIT = 0x82,
 402         TX_STATUS_FAIL_LONG_LIMIT = 0x83,
 403         TX_STATUS_FAIL_UNDERRUN = 0x84,
 404         TX_STATUS_FAIL_DRAIN_FLOW = 0x85,
 405         TX_STATUS_FAIL_RFKILL_FLUSH = 0x86,
 406         TX_STATUS_FAIL_LIFE_EXPIRE = 0x87,
 407         TX_STATUS_FAIL_DEST_PS = 0x88,
 408         TX_STATUS_FAIL_HOST_ABORTED = 0x89,
 409         TX_STATUS_FAIL_BT_RETRY = 0x8a,
 410         TX_STATUS_FAIL_STA_INVALID = 0x8b,
 411         TX_STATUS_FAIL_FRAG_DROPPED = 0x8c,
 412         TX_STATUS_FAIL_TID_DISABLE = 0x8d,
 413         TX_STATUS_FAIL_FIFO_FLUSHED = 0x8e,
 414         TX_STATUS_FAIL_SMALL_CF_POLL = 0x8f,
 415         TX_STATUS_FAIL_FW_DROP = 0x90,
 416         TX_STATUS_FAIL_STA_COLOR_MISMATCH = 0x91,
 417         TX_STATUS_INTERNAL_ABORT = 0x92,
 418         TX_MODE_MSK = 0x00000f00,
 419         TX_MODE_NO_BURST = 0x00000000,
 420         TX_MODE_IN_BURST_SEQ = 0x00000100,
 421         TX_MODE_FIRST_IN_BURST = 0x00000200,
 422         TX_QUEUE_NUM_MSK = 0x0001f000,
 423         TX_NARROW_BW_MSK = 0x00060000,
 424         TX_NARROW_BW_1DIV2 = 0x00020000,
 425         TX_NARROW_BW_1DIV4 = 0x00040000,
 426         TX_NARROW_BW_1DIV8 = 0x00060000,
 427 };
 428 
 429 /*
 430  * enum iwl_tx_agg_status - TX aggregation status
 431  * @AGG_TX_STATE_STATUS_MSK:
 432  * @AGG_TX_STATE_TRANSMITTED:
 433  * @AGG_TX_STATE_UNDERRUN:
 434  * @AGG_TX_STATE_BT_PRIO:
 435  * @AGG_TX_STATE_FEW_BYTES:
 436  * @AGG_TX_STATE_ABORT:
 437  * @AGG_TX_STATE_TX_ON_AIR_DROP: TX_ON_AIR signal drop without underrun or
 438  *      BT detection
 439  * @AGG_TX_STATE_LAST_SENT_TRY_CNT:
 440  * @AGG_TX_STATE_LAST_SENT_BT_KILL:
 441  * @AGG_TX_STATE_SCD_QUERY:
 442  * @AGG_TX_STATE_TEST_BAD_CRC32:
 443  * @AGG_TX_STATE_RESPONSE:
 444  * @AGG_TX_STATE_DUMP_TX:
 445  * @AGG_TX_STATE_DELAY_TX:
 446  * @AGG_TX_STATE_TRY_CNT_MSK: Retry count for 1st frame in aggregation (retries
 447  *      occur if tx failed for this frame when it was a member of a previous
 448  *      aggregation block). If rate scaling is used, retry count indicates the
 449  *      rate table entry used for all frames in the new agg.
 450  * @AGG_TX_STATE_SEQ_NUM_MSK: Command ID and sequence number of Tx command for
 451  *      this frame
 452  *
 453  * TODO: complete documentation
 454  */
 455 enum iwl_tx_agg_status {
 456         AGG_TX_STATE_STATUS_MSK = 0x00fff,
 457         AGG_TX_STATE_TRANSMITTED = 0x000,
 458         AGG_TX_STATE_UNDERRUN = 0x001,
 459         AGG_TX_STATE_BT_PRIO = 0x002,
 460         AGG_TX_STATE_FEW_BYTES = 0x004,
 461         AGG_TX_STATE_ABORT = 0x008,
 462         AGG_TX_STATE_TX_ON_AIR_DROP = 0x010,
 463         AGG_TX_STATE_LAST_SENT_TRY_CNT = 0x020,
 464         AGG_TX_STATE_LAST_SENT_BT_KILL = 0x040,
 465         AGG_TX_STATE_SCD_QUERY = 0x080,
 466         AGG_TX_STATE_TEST_BAD_CRC32 = 0x0100,
 467         AGG_TX_STATE_RESPONSE = 0x1ff,
 468         AGG_TX_STATE_DUMP_TX = 0x200,
 469         AGG_TX_STATE_DELAY_TX = 0x400,
 470         AGG_TX_STATE_TRY_CNT_POS = 12,
 471         AGG_TX_STATE_TRY_CNT_MSK = 0xf << AGG_TX_STATE_TRY_CNT_POS,
 472 };
 473 
 474 /*
 475  * The mask below describes a status where we are absolutely sure that the MPDU
 476  * wasn't sent. For BA/Underrun we cannot be that sure. All we know that we've
 477  * written the bytes to the TXE, but we know nothing about what the DSP did.
 478  */
 479 #define AGG_TX_STAT_FRAME_NOT_SENT (AGG_TX_STATE_FEW_BYTES | \
 480                                     AGG_TX_STATE_ABORT | \
 481                                     AGG_TX_STATE_SCD_QUERY)
 482 
 483 /*
 484  * REPLY_TX = 0x1c (response)
 485  *
 486  * This response may be in one of two slightly different formats, indicated
 487  * by the frame_count field:
 488  *
 489  * 1)   No aggregation (frame_count == 1).  This reports Tx results for a single
 490  *      frame. Multiple attempts, at various bit rates, may have been made for
 491  *      this frame.
 492  *
 493  * 2)   Aggregation (frame_count > 1).  This reports Tx results for two or more
 494  *      frames that used block-acknowledge.  All frames were transmitted at
 495  *      same rate. Rate scaling may have been used if first frame in this new
 496  *      agg block failed in previous agg block(s).
 497  *
 498  *      Note that, for aggregation, ACK (block-ack) status is not delivered
 499  *      here; block-ack has not been received by the time the device records
 500  *      this status.
 501  *      This status relates to reasons the tx might have been blocked or aborted
 502  *      within the device, rather than whether it was received successfully by
 503  *      the destination station.
 504  */
 505 
 506 /**
 507  * struct agg_tx_status - per packet TX aggregation status
 508  * @status: See &enum iwl_tx_agg_status
 509  * @sequence: Sequence # for this frame's Tx cmd (not SSN!)
 510  */
 511 struct agg_tx_status {
 512         __le16 status;
 513         __le16 sequence;
 514 } __packed;
 515 
 516 /*
 517  * definitions for initial rate index field
 518  * bits [3:0] initial rate index
 519  * bits [6:4] rate table color, used for the initial rate
 520  * bit-7 invalid rate indication
 521  */
 522 #define TX_RES_INIT_RATE_INDEX_MSK 0x0f
 523 #define TX_RES_RATE_TABLE_COLOR_POS 4
 524 #define TX_RES_RATE_TABLE_COLOR_MSK 0x70
 525 #define TX_RES_INV_RATE_INDEX_MSK 0x80
 526 #define TX_RES_RATE_TABLE_COL_GET(_f) (((_f) & TX_RES_RATE_TABLE_COLOR_MSK) >>\
 527                                        TX_RES_RATE_TABLE_COLOR_POS)
 528 
 529 #define IWL_MVM_TX_RES_GET_TID(_ra_tid) ((_ra_tid) & 0x0f)
 530 #define IWL_MVM_TX_RES_GET_RA(_ra_tid) ((_ra_tid) >> 4)
 531 
 532 /**
 533  * struct iwl_mvm_tx_resp_v3 - notifies that fw is TXing a packet
 534  * ( REPLY_TX = 0x1c )
 535  * @frame_count: 1 no aggregation, >1 aggregation
 536  * @bt_kill_count: num of times blocked by bluetooth (unused for agg)
 537  * @failure_rts: num of failures due to unsuccessful RTS
 538  * @failure_frame: num failures due to no ACK (unused for agg)
 539  * @initial_rate: for non-agg: rate of the successful Tx. For agg: rate of the
 540  *      Tx of all the batch. RATE_MCS_*
 541  * @wireless_media_time: for non-agg: RTS + CTS + frame tx attempts time + ACK.
 542  *      for agg: RTS + CTS + aggregation tx time + block-ack time.
 543  *      in usec.
 544  * @pa_status: tx power info
 545  * @pa_integ_res_a: tx power info
 546  * @pa_integ_res_b: tx power info
 547  * @pa_integ_res_c: tx power info
 548  * @measurement_req_id: tx power info
 549  * @reduced_tpc: transmit power reduction used
 550  * @reserved: reserved
 551  * @tfd_info: TFD information set by the FH
 552  * @seq_ctl: sequence control from the Tx cmd
 553  * @byte_cnt: byte count from the Tx cmd
 554  * @tlc_info: TLC rate info
 555  * @ra_tid: bits [3:0] = ra, bits [7:4] = tid
 556  * @frame_ctrl: frame control
 557  * @status: for non-agg:  frame status TX_STATUS_*
 558  *      for agg: status of 1st frame, AGG_TX_STATE_*; other frame status fields
 559  *      follow this one, up to frame_count. Length in @frame_count.
 560  *
 561  * After the array of statuses comes the SSN of the SCD. Look at
 562  * %iwl_mvm_get_scd_ssn for more details.
 563  */
 564 struct iwl_mvm_tx_resp_v3 {
 565         u8 frame_count;
 566         u8 bt_kill_count;
 567         u8 failure_rts;
 568         u8 failure_frame;
 569         __le32 initial_rate;
 570         __le16 wireless_media_time;
 571 
 572         u8 pa_status;
 573         u8 pa_integ_res_a[3];
 574         u8 pa_integ_res_b[3];
 575         u8 pa_integ_res_c[3];
 576         __le16 measurement_req_id;
 577         u8 reduced_tpc;
 578         u8 reserved;
 579 
 580         __le32 tfd_info;
 581         __le16 seq_ctl;
 582         __le16 byte_cnt;
 583         u8 tlc_info;
 584         u8 ra_tid;
 585         __le16 frame_ctrl;
 586         struct agg_tx_status status[];
 587 } __packed; /* TX_RSP_API_S_VER_3 */
 588 
 589 /**
 590  * struct iwl_mvm_tx_resp - notifies that fw is TXing a packet
 591  * ( REPLY_TX = 0x1c )
 592  * @frame_count: 1 no aggregation, >1 aggregation
 593  * @bt_kill_count: num of times blocked by bluetooth (unused for agg)
 594  * @failure_rts: num of failures due to unsuccessful RTS
 595  * @failure_frame: num failures due to no ACK (unused for agg)
 596  * @initial_rate: for non-agg: rate of the successful Tx. For agg: rate of the
 597  *      Tx of all the batch. RATE_MCS_*
 598  * @wireless_media_time: for non-agg: RTS + CTS + frame tx attempts time + ACK.
 599  *      for agg: RTS + CTS + aggregation tx time + block-ack time.
 600  *      in usec.
 601  * @pa_status: tx power info
 602  * @pa_integ_res_a: tx power info
 603  * @pa_integ_res_b: tx power info
 604  * @pa_integ_res_c: tx power info
 605  * @measurement_req_id: tx power info
 606  * @reduced_tpc: transmit power reduction used
 607  * @reserved: reserved
 608  * @tfd_info: TFD information set by the FH
 609  * @seq_ctl: sequence control from the Tx cmd
 610  * @byte_cnt: byte count from the Tx cmd
 611  * @tlc_info: TLC rate info
 612  * @ra_tid: bits [3:0] = ra, bits [7:4] = tid
 613  * @frame_ctrl: frame control
 614  * @tx_queue: TX queue for this response
 615  * @reserved2: reserved for padding/alignment
 616  * @status: for non-agg:  frame status TX_STATUS_*
 617  *      For version 6 TX response isn't received for aggregation at all.
 618  *
 619  * After the array of statuses comes the SSN of the SCD. Look at
 620  * %iwl_mvm_get_scd_ssn for more details.
 621  */
 622 struct iwl_mvm_tx_resp {
 623         u8 frame_count;
 624         u8 bt_kill_count;
 625         u8 failure_rts;
 626         u8 failure_frame;
 627         __le32 initial_rate;
 628         __le16 wireless_media_time;
 629 
 630         u8 pa_status;
 631         u8 pa_integ_res_a[3];
 632         u8 pa_integ_res_b[3];
 633         u8 pa_integ_res_c[3];
 634         __le16 measurement_req_id;
 635         u8 reduced_tpc;
 636         u8 reserved;
 637 
 638         __le32 tfd_info;
 639         __le16 seq_ctl;
 640         __le16 byte_cnt;
 641         u8 tlc_info;
 642         u8 ra_tid;
 643         __le16 frame_ctrl;
 644         __le16 tx_queue;
 645         __le16 reserved2;
 646         struct agg_tx_status status;
 647 } __packed; /* TX_RSP_API_S_VER_6 */
 648 
 649 /**
 650  * struct iwl_mvm_ba_notif - notifies about reception of BA
 651  * ( BA_NOTIF = 0xc5 )
 652  * @sta_addr: MAC address
 653  * @reserved: reserved
 654  * @sta_id: Index of recipient (BA-sending) station in fw's station table
 655  * @tid: tid of the session
 656  * @seq_ctl: sequence control field
 657  * @bitmap: the bitmap of the BA notification as seen in the air
 658  * @scd_flow: the tx queue this BA relates to
 659  * @scd_ssn: the index of the last contiguously sent packet
 660  * @txed: number of Txed frames in this batch
 661  * @txed_2_done: number of Acked frames in this batch
 662  * @reduced_txp: power reduced according to TPC. This is the actual value and
 663  *      not a copy from the LQ command. Thus, if not the first rate was used
 664  *      for Tx-ing then this value will be set to 0 by FW.
 665  * @reserved1: reserved
 666  */
 667 struct iwl_mvm_ba_notif {
 668         u8 sta_addr[ETH_ALEN];
 669         __le16 reserved;
 670 
 671         u8 sta_id;
 672         u8 tid;
 673         __le16 seq_ctl;
 674         __le64 bitmap;
 675         __le16 scd_flow;
 676         __le16 scd_ssn;
 677         u8 txed;
 678         u8 txed_2_done;
 679         u8 reduced_txp;
 680         u8 reserved1;
 681 } __packed;
 682 
 683 /**
 684  * struct iwl_mvm_compressed_ba_tfd - progress of a TFD queue
 685  * @q_num: TFD queue number
 686  * @tfd_index: Index of first un-acked frame in the  TFD queue
 687  * @scd_queue: For debug only - the physical queue the TFD queue is bound to
 688  * @tid: TID of the queue (0-7)
 689  * @reserved: reserved for alignment
 690  */
 691 struct iwl_mvm_compressed_ba_tfd {
 692         __le16 q_num;
 693         __le16 tfd_index;
 694         u8 scd_queue;
 695         u8 tid;
 696         u8 reserved[2];
 697 } __packed; /* COMPRESSED_BA_TFD_API_S_VER_1 */
 698 
 699 /**
 700  * struct iwl_mvm_compressed_ba_ratid - progress of a RA TID queue
 701  * @q_num: RA TID queue number
 702  * @tid: TID of the queue
 703  * @ssn: BA window current SSN
 704  */
 705 struct iwl_mvm_compressed_ba_ratid {
 706         u8 q_num;
 707         u8 tid;
 708         __le16 ssn;
 709 } __packed; /* COMPRESSED_BA_RATID_API_S_VER_1 */
 710 
 711 /*
 712  * enum iwl_mvm_ba_resp_flags - TX aggregation status
 713  * @IWL_MVM_BA_RESP_TX_AGG: generated due to BA
 714  * @IWL_MVM_BA_RESP_TX_BAR: generated due to BA after BAR
 715  * @IWL_MVM_BA_RESP_TX_AGG_FAIL: aggregation didn't receive BA
 716  * @IWL_MVM_BA_RESP_TX_UNDERRUN: aggregation got underrun
 717  * @IWL_MVM_BA_RESP_TX_BT_KILL: aggregation got BT-kill
 718  * @IWL_MVM_BA_RESP_TX_DSP_TIMEOUT: aggregation didn't finish within the
 719  *      expected time
 720  */
 721 enum iwl_mvm_ba_resp_flags {
 722         IWL_MVM_BA_RESP_TX_AGG,
 723         IWL_MVM_BA_RESP_TX_BAR,
 724         IWL_MVM_BA_RESP_TX_AGG_FAIL,
 725         IWL_MVM_BA_RESP_TX_UNDERRUN,
 726         IWL_MVM_BA_RESP_TX_BT_KILL,
 727         IWL_MVM_BA_RESP_TX_DSP_TIMEOUT
 728 };
 729 
 730 /**
 731  * struct iwl_mvm_compressed_ba_notif - notifies about reception of BA
 732  * ( BA_NOTIF = 0xc5 )
 733  * @flags: status flag, see the &iwl_mvm_ba_resp_flags
 734  * @sta_id: Index of recipient (BA-sending) station in fw's station table
 735  * @reduced_txp: power reduced according to TPC. This is the actual value and
 736  *      not a copy from the LQ command. Thus, if not the first rate was used
 737  *      for Tx-ing then this value will be set to 0 by FW.
 738  * @tlc_rate_info: TLC rate info, initial rate index, TLC table color
 739  * @retry_cnt: retry count
 740  * @query_byte_cnt: SCD query byte count
 741  * @query_frame_cnt: SCD query frame count
 742  * @txed: number of frames sent in the aggregation (all-TIDs)
 743  * @done: number of frames that were Acked by the BA (all-TIDs)
 744  * @reserved: reserved (for alignment)
 745  * @wireless_time: Wireless-media time
 746  * @tx_rate: the rate the aggregation was sent at
 747  * @tfd_cnt: number of TFD-Q elements
 748  * @ra_tid_cnt: number of RATID-Q elements
 749  * @tfd: array of TFD queue status updates. See &iwl_mvm_compressed_ba_tfd
 750  *      for details. Length in @tfd_cnt.
 751  * @ra_tid: array of RA-TID queue status updates. For debug purposes only. See
 752  *      &iwl_mvm_compressed_ba_ratid for more details. Length in @ra_tid_cnt.
 753  */
 754 struct iwl_mvm_compressed_ba_notif {
 755         __le32 flags;
 756         u8 sta_id;
 757         u8 reduced_txp;
 758         u8 tlc_rate_info;
 759         u8 retry_cnt;
 760         __le32 query_byte_cnt;
 761         __le16 query_frame_cnt;
 762         __le16 txed;
 763         __le16 done;
 764         __le16 reserved;
 765         __le32 wireless_time;
 766         __le32 tx_rate;
 767         __le16 tfd_cnt;
 768         __le16 ra_tid_cnt;
 769         struct iwl_mvm_compressed_ba_tfd tfd[0];
 770         struct iwl_mvm_compressed_ba_ratid ra_tid[0];
 771 } __packed; /* COMPRESSED_BA_RES_API_S_VER_4 */
 772 
 773 /**
 774  * struct iwl_mac_beacon_cmd_v6 - beacon template command
 775  * @tx: the tx commands associated with the beacon frame
 776  * @template_id: currently equal to the mac context id of the coresponding
 777  *  mac.
 778  * @tim_idx: the offset of the tim IE in the beacon
 779  * @tim_size: the length of the tim IE
 780  * @frame: the template of the beacon frame
 781  */
 782 struct iwl_mac_beacon_cmd_v6 {
 783         struct iwl_tx_cmd tx;
 784         __le32 template_id;
 785         __le32 tim_idx;
 786         __le32 tim_size;
 787         struct ieee80211_hdr frame[0];
 788 } __packed; /* BEACON_TEMPLATE_CMD_API_S_VER_6 */
 789 
 790 /**
 791  * struct iwl_mac_beacon_cmd_v7 - beacon template command with offloaded CSA
 792  * @tx: the tx commands associated with the beacon frame
 793  * @template_id: currently equal to the mac context id of the coresponding
 794  *  mac.
 795  * @tim_idx: the offset of the tim IE in the beacon
 796  * @tim_size: the length of the tim IE
 797  * @ecsa_offset: offset to the ECSA IE if present
 798  * @csa_offset: offset to the CSA IE if present
 799  * @frame: the template of the beacon frame
 800  */
 801 struct iwl_mac_beacon_cmd_v7 {
 802         struct iwl_tx_cmd tx;
 803         __le32 template_id;
 804         __le32 tim_idx;
 805         __le32 tim_size;
 806         __le32 ecsa_offset;
 807         __le32 csa_offset;
 808         struct ieee80211_hdr frame[0];
 809 } __packed; /* BEACON_TEMPLATE_CMD_API_S_VER_7 */
 810 
 811 enum iwl_mac_beacon_flags {
 812         IWL_MAC_BEACON_CCK      = BIT(8),
 813         IWL_MAC_BEACON_ANT_A    = BIT(9),
 814         IWL_MAC_BEACON_ANT_B    = BIT(10),
 815         IWL_MAC_BEACON_ANT_C    = BIT(11),
 816 };
 817 
 818 /**
 819  * struct iwl_mac_beacon_cmd - beacon template command with offloaded CSA
 820  * @byte_cnt: byte count of the beacon frame.
 821  * @flags: least significant byte for rate code. The most significant byte
 822  *      is &enum iwl_mac_beacon_flags.
 823  * @reserved: reserved
 824  * @template_id: currently equal to the mac context id of the coresponding mac.
 825  * @tim_idx: the offset of the tim IE in the beacon
 826  * @tim_size: the length of the tim IE
 827  * @ecsa_offset: offset to the ECSA IE if present
 828  * @csa_offset: offset to the CSA IE if present
 829  * @frame: the template of the beacon frame
 830  */
 831 struct iwl_mac_beacon_cmd {
 832         __le16 byte_cnt;
 833         __le16 flags;
 834         __le64 reserved;
 835         __le32 template_id;
 836         __le32 tim_idx;
 837         __le32 tim_size;
 838         __le32 ecsa_offset;
 839         __le32 csa_offset;
 840         struct ieee80211_hdr frame[0];
 841 } __packed; /* BEACON_TEMPLATE_CMD_API_S_VER_9 */
 842 
 843 struct iwl_beacon_notif {
 844         struct iwl_mvm_tx_resp beacon_notify_hdr;
 845         __le64 tsf;
 846         __le32 ibss_mgr_status;
 847 } __packed;
 848 
 849 /**
 850  * struct iwl_extended_beacon_notif_v5 - notifies about beacon transmission
 851  * @beacon_notify_hdr: tx response command associated with the beacon
 852  * @tsf: last beacon tsf
 853  * @ibss_mgr_status: whether IBSS is manager
 854  * @gp2: last beacon time in gp2
 855  */
 856 struct iwl_extended_beacon_notif_v5 {
 857         struct iwl_mvm_tx_resp beacon_notify_hdr;
 858         __le64 tsf;
 859         __le32 ibss_mgr_status;
 860         __le32 gp2;
 861 } __packed; /* BEACON_NTFY_API_S_VER_5 */
 862 
 863 /**
 864  * struct iwl_extended_beacon_notif - notifies about beacon transmission
 865  * @status: the status of the Tx response of the beacon
 866  * @tsf: last beacon tsf
 867  * @ibss_mgr_status: whether IBSS is manager
 868  * @gp2: last beacon time in gp2
 869  */
 870 struct iwl_extended_beacon_notif {
 871         __le32 status;
 872         __le64 tsf;
 873         __le32 ibss_mgr_status;
 874         __le32 gp2;
 875 } __packed; /* BEACON_NTFY_API_S_VER_6_ */
 876 
 877 /**
 878  * enum iwl_dump_control - dump (flush) control flags
 879  * @DUMP_TX_FIFO_FLUSH: Dump MSDUs until the the FIFO is empty
 880  *      and the TFD queues are empty.
 881  */
 882 enum iwl_dump_control {
 883         DUMP_TX_FIFO_FLUSH      = BIT(1),
 884 };
 885 
 886 /**
 887  * struct iwl_tx_path_flush_cmd -- queue/FIFO flush command
 888  * @queues_ctl: bitmap of queues to flush
 889  * @flush_ctl: control flags
 890  * @reserved: reserved
 891  */
 892 struct iwl_tx_path_flush_cmd_v1 {
 893         __le32 queues_ctl;
 894         __le16 flush_ctl;
 895         __le16 reserved;
 896 } __packed; /* TX_PATH_FLUSH_CMD_API_S_VER_1 */
 897 
 898 /**
 899  * struct iwl_tx_path_flush_cmd -- queue/FIFO flush command
 900  * @sta_id: station ID to flush
 901  * @tid_mask: TID mask to flush
 902  * @reserved: reserved
 903  */
 904 struct iwl_tx_path_flush_cmd {
 905         __le32 sta_id;
 906         __le16 tid_mask;
 907         __le16 reserved;
 908 } __packed; /* TX_PATH_FLUSH_CMD_API_S_VER_2 */
 909 
 910 /* Available options for the SCD_QUEUE_CFG HCMD */
 911 enum iwl_scd_cfg_actions {
 912         SCD_CFG_DISABLE_QUEUE           = 0x0,
 913         SCD_CFG_ENABLE_QUEUE            = 0x1,
 914         SCD_CFG_UPDATE_QUEUE_TID        = 0x2,
 915 };
 916 
 917 /**
 918  * struct iwl_scd_txq_cfg_cmd - New txq hw scheduler config command
 919  * @token: unused
 920  * @sta_id: station id
 921  * @tid: TID
 922  * @scd_queue: scheduler queue to confiug
 923  * @action: 1 queue enable, 0 queue disable, 2 change txq's tid owner
 924  *      Value is one of &enum iwl_scd_cfg_actions options
 925  * @aggregate: 1 aggregated queue, 0 otherwise
 926  * @tx_fifo: &enum iwl_mvm_tx_fifo
 927  * @window: BA window size
 928  * @ssn: SSN for the BA agreement
 929  * @reserved: reserved
 930  */
 931 struct iwl_scd_txq_cfg_cmd {
 932         u8 token;
 933         u8 sta_id;
 934         u8 tid;
 935         u8 scd_queue;
 936         u8 action;
 937         u8 aggregate;
 938         u8 tx_fifo;
 939         u8 window;
 940         __le16 ssn;
 941         __le16 reserved;
 942 } __packed; /* SCD_QUEUE_CFG_CMD_API_S_VER_1 */
 943 
 944 /**
 945  * struct iwl_scd_txq_cfg_rsp
 946  * @token: taken from the command
 947  * @sta_id: station id from the command
 948  * @tid: tid from the command
 949  * @scd_queue: scd_queue from the command
 950  */
 951 struct iwl_scd_txq_cfg_rsp {
 952         u8 token;
 953         u8 sta_id;
 954         u8 tid;
 955         u8 scd_queue;
 956 } __packed; /* SCD_QUEUE_CFG_RSP_API_S_VER_1 */
 957 
 958 #endif /* __iwl_fw_api_tx_h__ */

/* [<][>][^][v][top][bottom][index][help] */