drivers/net/ethernet/chelsio/cxgb/subr.c

/* [<][>][^][v][top][bottom][index][help] */
This source file includes following definitions.
t1_wait_op_done
__t1_tpi_write
t1_tpi_write
__t1_tpi_read
t1_tpi_read
t1_tpi_par
t1_link_changed
t1_pci_intr_handler
fpga_phy_intr_handler
fpga_slow_intr
mi1_wait_until_ready
mi1_mdio_init
mi1_mdio_read
mi1_mdio_write
mi1_mdio_ext_read
mi1_mdio_ext_write
t1_get_board_info
t1_seeprom_read
t1_eeprom_vpd_get
vpd_macaddress_get
t1_link_start
t1_elmer0_ext_intr_handler
t1_interrupts_enable
t1_interrupts_disable
t1_interrupts_clear
asic_slow_intr
t1_slow_intr_handler
power_sequence_xpak
t1_get_board_rev
board_init
t1_init_hw_modules
get_pci_mode
t1_free_sw_modules
init_link_config
t1_init_sw_modules
   1 /*****************************************************************************
   2  *                                                                           *
   3  * File: subr.c                                                              *
   4  * $Revision: 1.27 $                                                         *
   5  * $Date: 2005/06/22 01:08:36 $                                              *
   6  * Description:                                                              *
   7  *  Various subroutines (intr,pio,etc.) used by Chelsio 10G Ethernet driver. *
   8  *  part of the Chelsio 10Gb Ethernet Driver.                                *
   9  *                                                                           *
  10  * This program is free software; you can redistribute it and/or modify      *
  11  * it under the terms of the GNU General Public License, version 2, as       *
  12  * published by the Free Software Foundation.                                *
  13  *                                                                           *
  14  * You should have received a copy of the GNU General Public License along   *
  15  * with this program; if not, see <http://www.gnu.org/licenses/>.            *
  16  *                                                                           *
  17  * THIS SOFTWARE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR IMPLIED    *
  18  * WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF      *
  19  * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.                     *
  20  *                                                                           *
  21  * http://www.chelsio.com                                                    *
  22  *                                                                           *
  23  * Copyright (c) 2003 - 2005 Chelsio Communications, Inc.                    *
  24  * All rights reserved.                                                      *
  25  *                                                                           *
  26  * Maintainers: maintainers@chelsio.com                                      *
  27  *                                                                           *
  28  * Authors: Dimitrios Michailidis   <dm@chelsio.com>                         *
  29  *          Tina Yang               <tainay@chelsio.com>                     *
  30  *          Felix Marti             <felix@chelsio.com>                      *
  31  *          Scott Bardone           <sbardone@chelsio.com>                   *
  32  *          Kurt Ottaway            <kottaway@chelsio.com>                   *
  33  *          Frank DiMambro          <frank@chelsio.com>                      *
  34  *                                                                           *
  35  * History:                                                                  *
  36  *                                                                           *
  37  ****************************************************************************/
  38 
  39 #include "common.h"
  40 #include "elmer0.h"
  41 #include "regs.h"
  42 #include "gmac.h"
  43 #include "cphy.h"
  44 #include "sge.h"
  45 #include "tp.h"
  46 #include "espi.h"
  47 
  48 /**
  49  *      t1_wait_op_done - wait until an operation is completed
  50  *      @adapter: the adapter performing the operation
  51  *      @reg: the register to check for completion
  52  *      @mask: a single-bit field within @reg that indicates completion
  53  *      @polarity: the value of the field when the operation is completed
  54  *      @attempts: number of check iterations
  55  *      @delay: delay in usecs between iterations
  56  *
  57  *      Wait until an operation is completed by checking a bit in a register
  58  *      up to @attempts times.  Returns %0 if the operation completes and %1
  59  *      otherwise.
  60  */
  61 static int t1_wait_op_done(adapter_t *adapter, int reg, u32 mask, int polarity,
  62                            int attempts, int delay)
  63 {
  64         while (1) {
  65                 u32 val = readl(adapter->regs + reg) & mask;
  66 
  67                 if (!!val == polarity)
  68                         return 0;
  69                 if (--attempts == 0)
  70                         return 1;
  71                 if (delay)
  72                         udelay(delay);
  73         }
  74 }
  75 
  76 #define TPI_ATTEMPTS 50
  77 
  78 /*
  79  * Write a register over the TPI interface (unlocked and locked versions).
  80  */
  81 int __t1_tpi_write(adapter_t *adapter, u32 addr, u32 value)
  82 {
  83         int tpi_busy;
  84 
  85         writel(addr, adapter->regs + A_TPI_ADDR);
  86         writel(value, adapter->regs + A_TPI_WR_DATA);
  87         writel(F_TPIWR, adapter->regs + A_TPI_CSR);
  88 
  89         tpi_busy = t1_wait_op_done(adapter, A_TPI_CSR, F_TPIRDY, 1,
  90                                    TPI_ATTEMPTS, 3);
  91         if (tpi_busy)
  92                 pr_alert("%s: TPI write to 0x%x failed\n",
  93                          adapter->name, addr);
  94         return tpi_busy;
  95 }
  96 
  97 int t1_tpi_write(adapter_t *adapter, u32 addr, u32 value)
  98 {
  99         int ret;
 100 
 101         spin_lock(&adapter->tpi_lock);
 102         ret = __t1_tpi_write(adapter, addr, value);
 103         spin_unlock(&adapter->tpi_lock);
 104         return ret;
 105 }
 106 
 107 /*
 108  * Read a register over the TPI interface (unlocked and locked versions).
 109  */
 110 int __t1_tpi_read(adapter_t *adapter, u32 addr, u32 *valp)
 111 {
 112         int tpi_busy;
 113 
 114         writel(addr, adapter->regs + A_TPI_ADDR);
 115         writel(0, adapter->regs + A_TPI_CSR);
 116 
 117         tpi_busy = t1_wait_op_done(adapter, A_TPI_CSR, F_TPIRDY, 1,
 118                                    TPI_ATTEMPTS, 3);
 119         if (tpi_busy)
 120                 pr_alert("%s: TPI read from 0x%x failed\n",
 121                          adapter->name, addr);
 122         else
 123                 *valp = readl(adapter->regs + A_TPI_RD_DATA);
 124         return tpi_busy;
 125 }
 126 
 127 int t1_tpi_read(adapter_t *adapter, u32 addr, u32 *valp)
 128 {
 129         int ret;
 130 
 131         spin_lock(&adapter->tpi_lock);
 132         ret = __t1_tpi_read(adapter, addr, valp);
 133         spin_unlock(&adapter->tpi_lock);
 134         return ret;
 135 }
 136 
 137 /*
 138  * Set a TPI parameter.
 139  */
 140 static void t1_tpi_par(adapter_t *adapter, u32 value)
 141 {
 142         writel(V_TPIPAR(value), adapter->regs + A_TPI_PAR);
 143 }
 144 
 145 /*
 146  * Called when a port's link settings change to propagate the new values to the
 147  * associated PHY and MAC.  After performing the common tasks it invokes an
 148  * OS-specific handler.
 149  */
 150 void t1_link_changed(adapter_t *adapter, int port_id)
 151 {
 152         int link_ok, speed, duplex, fc;
 153         struct cphy *phy = adapter->port[port_id].phy;
 154         struct link_config *lc = &adapter->port[port_id].link_config;
 155 
 156         phy->ops->get_link_status(phy, &link_ok, &speed, &duplex, &fc);
 157 
 158         lc->speed = speed < 0 ? SPEED_INVALID : speed;
 159         lc->duplex = duplex < 0 ? DUPLEX_INVALID : duplex;
 160         if (!(lc->requested_fc & PAUSE_AUTONEG))
 161                 fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX);
 162 
 163         if (link_ok && speed >= 0 && lc->autoneg == AUTONEG_ENABLE) {
 164                 /* Set MAC speed, duplex, and flow control to match PHY. */
 165                 struct cmac *mac = adapter->port[port_id].mac;
 166 
 167                 mac->ops->set_speed_duplex_fc(mac, speed, duplex, fc);
 168                 lc->fc = (unsigned char)fc;
 169         }
 170         t1_link_negotiated(adapter, port_id, link_ok, speed, duplex, fc);
 171 }
 172 
 173 static int t1_pci_intr_handler(adapter_t *adapter)
 174 {
 175         u32 pcix_cause;
 176 
 177         pci_read_config_dword(adapter->pdev, A_PCICFG_INTR_CAUSE, &pcix_cause);
 178 
 179         if (pcix_cause) {
 180                 pci_write_config_dword(adapter->pdev, A_PCICFG_INTR_CAUSE,
 181                                        pcix_cause);
 182                 t1_fatal_err(adapter);    /* PCI errors are fatal */
 183         }
 184         return 0;
 185 }
 186 
 187 #ifdef CONFIG_CHELSIO_T1_1G
 188 #include "fpga_defs.h"
 189 
 190 /*
 191  * PHY interrupt handler for FPGA boards.
 192  */
 193 static int fpga_phy_intr_handler(adapter_t *adapter)
 194 {
 195         int p;
 196         u32 cause = readl(adapter->regs + FPGA_GMAC_ADDR_INTERRUPT_CAUSE);
 197 
 198         for_each_port(adapter, p)
 199                 if (cause & (1 << p)) {
 200                         struct cphy *phy = adapter->port[p].phy;
 201                         int phy_cause = phy->ops->interrupt_handler(phy);
 202 
 203                         if (phy_cause & cphy_cause_link_change)
 204                                 t1_link_changed(adapter, p);
 205                 }
 206         writel(cause, adapter->regs + FPGA_GMAC_ADDR_INTERRUPT_CAUSE);
 207         return 0;
 208 }
 209 
 210 /*
 211  * Slow path interrupt handler for FPGAs.
 212  */
 213 static int fpga_slow_intr(adapter_t *adapter)
 214 {
 215         u32 cause = readl(adapter->regs + A_PL_CAUSE);
 216 
 217         cause &= ~F_PL_INTR_SGE_DATA;
 218         if (cause & F_PL_INTR_SGE_ERR)
 219                 t1_sge_intr_error_handler(adapter->sge);
 220 
 221         if (cause & FPGA_PCIX_INTERRUPT_GMAC)
 222                 fpga_phy_intr_handler(adapter);
 223 
 224         if (cause & FPGA_PCIX_INTERRUPT_TP) {
 225                 /*
 226                  * FPGA doesn't support MC4 interrupts and it requires
 227                  * this odd layer of indirection for MC5.
 228                  */
 229                 u32 tp_cause = readl(adapter->regs + FPGA_TP_ADDR_INTERRUPT_CAUSE);
 230 
 231                 /* Clear TP interrupt */
 232                 writel(tp_cause, adapter->regs + FPGA_TP_ADDR_INTERRUPT_CAUSE);
 233         }
 234         if (cause & FPGA_PCIX_INTERRUPT_PCIX)
 235                 t1_pci_intr_handler(adapter);
 236 
 237         /* Clear the interrupts just processed. */
 238         if (cause)
 239                 writel(cause, adapter->regs + A_PL_CAUSE);
 240 
 241         return cause != 0;
 242 }
 243 #endif
 244 
 245 /*
 246  * Wait until Elmer's MI1 interface is ready for new operations.
 247  */
 248 static int mi1_wait_until_ready(adapter_t *adapter, int mi1_reg)
 249 {
 250         int attempts = 100, busy;
 251 
 252         do {
 253                 u32 val;
 254 
 255                 __t1_tpi_read(adapter, mi1_reg, &val);
 256                 busy = val & F_MI1_OP_BUSY;
 257                 if (busy)
 258                         udelay(10);
 259         } while (busy && --attempts);
 260         if (busy)
 261                 pr_alert("%s: MDIO operation timed out\n", adapter->name);
 262         return busy;
 263 }
 264 
 265 /*
 266  * MI1 MDIO initialization.
 267  */
 268 static void mi1_mdio_init(adapter_t *adapter, const struct board_info *bi)
 269 {
 270         u32 clkdiv = bi->clock_elmer0 / (2 * bi->mdio_mdc) - 1;
 271         u32 val = F_MI1_PREAMBLE_ENABLE | V_MI1_MDI_INVERT(bi->mdio_mdiinv) |
 272                 V_MI1_MDI_ENABLE(bi->mdio_mdien) | V_MI1_CLK_DIV(clkdiv);
 273 
 274         if (!(bi->caps & SUPPORTED_10000baseT_Full))
 275                 val |= V_MI1_SOF(1);
 276         t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_CFG, val);
 277 }
 278 
 279 #if defined(CONFIG_CHELSIO_T1_1G)
 280 /*
 281  * Elmer MI1 MDIO read/write operations.
 282  */
 283 static int mi1_mdio_read(struct net_device *dev, int phy_addr, int mmd_addr,
 284                          u16 reg_addr)
 285 {
 286         struct adapter *adapter = dev->ml_priv;
 287         u32 addr = V_MI1_REG_ADDR(reg_addr) | V_MI1_PHY_ADDR(phy_addr);
 288         unsigned int val;
 289 
 290         spin_lock(&adapter->tpi_lock);
 291         __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_ADDR, addr);
 292         __t1_tpi_write(adapter,
 293                         A_ELMER0_PORT0_MI1_OP, MI1_OP_DIRECT_READ);
 294         mi1_wait_until_ready(adapter, A_ELMER0_PORT0_MI1_OP);
 295         __t1_tpi_read(adapter, A_ELMER0_PORT0_MI1_DATA, &val);
 296         spin_unlock(&adapter->tpi_lock);
 297         return val;
 298 }
 299 
 300 static int mi1_mdio_write(struct net_device *dev, int phy_addr, int mmd_addr,
 301                           u16 reg_addr, u16 val)
 302 {
 303         struct adapter *adapter = dev->ml_priv;
 304         u32 addr = V_MI1_REG_ADDR(reg_addr) | V_MI1_PHY_ADDR(phy_addr);
 305 
 306         spin_lock(&adapter->tpi_lock);
 307         __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_ADDR, addr);
 308         __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_DATA, val);
 309         __t1_tpi_write(adapter,
 310                         A_ELMER0_PORT0_MI1_OP, MI1_OP_DIRECT_WRITE);
 311         mi1_wait_until_ready(adapter, A_ELMER0_PORT0_MI1_OP);
 312         spin_unlock(&adapter->tpi_lock);
 313         return 0;
 314 }
 315 
 316 static const struct mdio_ops mi1_mdio_ops = {
 317         .init = mi1_mdio_init,
 318         .read = mi1_mdio_read,
 319         .write = mi1_mdio_write,
 320         .mode_support = MDIO_SUPPORTS_C22
 321 };
 322 
 323 #endif
 324 
 325 static int mi1_mdio_ext_read(struct net_device *dev, int phy_addr, int mmd_addr,
 326                              u16 reg_addr)
 327 {
 328         struct adapter *adapter = dev->ml_priv;
 329         u32 addr = V_MI1_REG_ADDR(mmd_addr) | V_MI1_PHY_ADDR(phy_addr);
 330         unsigned int val;
 331 
 332         spin_lock(&adapter->tpi_lock);
 333 
 334         /* Write the address we want. */
 335         __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_ADDR, addr);
 336         __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_DATA, reg_addr);
 337         __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_OP,
 338                        MI1_OP_INDIRECT_ADDRESS);
 339         mi1_wait_until_ready(adapter, A_ELMER0_PORT0_MI1_OP);
 340 
 341         /* Write the operation we want. */
 342         __t1_tpi_write(adapter,
 343                         A_ELMER0_PORT0_MI1_OP, MI1_OP_INDIRECT_READ);
 344         mi1_wait_until_ready(adapter, A_ELMER0_PORT0_MI1_OP);
 345 
 346         /* Read the data. */
 347         __t1_tpi_read(adapter, A_ELMER0_PORT0_MI1_DATA, &val);
 348         spin_unlock(&adapter->tpi_lock);
 349         return val;
 350 }
 351 
 352 static int mi1_mdio_ext_write(struct net_device *dev, int phy_addr,
 353                               int mmd_addr, u16 reg_addr, u16 val)
 354 {
 355         struct adapter *adapter = dev->ml_priv;
 356         u32 addr = V_MI1_REG_ADDR(mmd_addr) | V_MI1_PHY_ADDR(phy_addr);
 357 
 358         spin_lock(&adapter->tpi_lock);
 359 
 360         /* Write the address we want. */
 361         __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_ADDR, addr);
 362         __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_DATA, reg_addr);
 363         __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_OP,
 364                        MI1_OP_INDIRECT_ADDRESS);
 365         mi1_wait_until_ready(adapter, A_ELMER0_PORT0_MI1_OP);
 366 
 367         /* Write the data. */
 368         __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_DATA, val);
 369         __t1_tpi_write(adapter, A_ELMER0_PORT0_MI1_OP, MI1_OP_INDIRECT_WRITE);
 370         mi1_wait_until_ready(adapter, A_ELMER0_PORT0_MI1_OP);
 371         spin_unlock(&adapter->tpi_lock);
 372         return 0;
 373 }
 374 
 375 static const struct mdio_ops mi1_mdio_ext_ops = {
 376         .init = mi1_mdio_init,
 377         .read = mi1_mdio_ext_read,
 378         .write = mi1_mdio_ext_write,
 379         .mode_support = MDIO_SUPPORTS_C45 | MDIO_EMULATE_C22
 380 };
 381 
 382 enum {
 383         CH_BRD_T110_1CU,
 384         CH_BRD_N110_1F,
 385         CH_BRD_N210_1F,
 386         CH_BRD_T210_1F,
 387         CH_BRD_T210_1CU,
 388         CH_BRD_N204_4CU,
 389 };
 390 
 391 static const struct board_info t1_board[] = {
 392         {
 393                 .board          = CHBT_BOARD_CHT110,
 394                 .port_number    = 1,
 395                 .caps           = SUPPORTED_10000baseT_Full,
 396                 .chip_term      = CHBT_TERM_T1,
 397                 .chip_mac       = CHBT_MAC_PM3393,
 398                 .chip_phy       = CHBT_PHY_MY3126,
 399                 .clock_core     = 125000000,
 400                 .clock_mc3      = 150000000,
 401                 .clock_mc4      = 125000000,
 402                 .espi_nports    = 1,
 403                 .clock_elmer0   = 44,
 404                 .mdio_mdien     = 1,
 405                 .mdio_mdiinv    = 1,
 406                 .mdio_mdc       = 1,
 407                 .mdio_phybaseaddr = 1,
 408                 .gmac           = &t1_pm3393_ops,
 409                 .gphy           = &t1_my3126_ops,
 410                 .mdio_ops       = &mi1_mdio_ext_ops,
 411                 .desc           = "Chelsio T110 1x10GBase-CX4 TOE",
 412         },
 413 
 414         {
 415                 .board          = CHBT_BOARD_N110,
 416                 .port_number    = 1,
 417                 .caps           = SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE,
 418                 .chip_term      = CHBT_TERM_T1,
 419                 .chip_mac       = CHBT_MAC_PM3393,
 420                 .chip_phy       = CHBT_PHY_88X2010,
 421                 .clock_core     = 125000000,
 422                 .espi_nports    = 1,
 423                 .clock_elmer0   = 44,
 424                 .mdio_mdien     = 0,
 425                 .mdio_mdiinv    = 0,
 426                 .mdio_mdc       = 1,
 427                 .mdio_phybaseaddr = 0,
 428                 .gmac           = &t1_pm3393_ops,
 429                 .gphy           = &t1_mv88x201x_ops,
 430                 .mdio_ops       = &mi1_mdio_ext_ops,
 431                 .desc           = "Chelsio N110 1x10GBaseX NIC",
 432         },
 433 
 434         {
 435                 .board          = CHBT_BOARD_N210,
 436                 .port_number    = 1,
 437                 .caps           = SUPPORTED_10000baseT_Full | SUPPORTED_FIBRE,
 438                 .chip_term      = CHBT_TERM_T2,
 439                 .chip_mac       = CHBT_MAC_PM3393,
 440                 .chip_phy       = CHBT_PHY_88X2010,
 441                 .clock_core     = 125000000,
 442                 .espi_nports    = 1,
 443                 .clock_elmer0   = 44,
 444                 .mdio_mdien     = 0,
 445                 .mdio_mdiinv    = 0,
 446                 .mdio_mdc       = 1,
 447                 .mdio_phybaseaddr = 0,
 448                 .gmac           = &t1_pm3393_ops,
 449                 .gphy           = &t1_mv88x201x_ops,
 450                 .mdio_ops       = &mi1_mdio_ext_ops,
 451                 .desc           = "Chelsio N210 1x10GBaseX NIC",
 452         },
 453 
 454         {
 455                 .board          = CHBT_BOARD_CHT210,
 456                 .port_number    = 1,
 457                 .caps           = SUPPORTED_10000baseT_Full,
 458                 .chip_term      = CHBT_TERM_T2,
 459                 .chip_mac       = CHBT_MAC_PM3393,
 460                 .chip_phy       = CHBT_PHY_88X2010,
 461                 .clock_core     = 125000000,
 462                 .clock_mc3      = 133000000,
 463                 .clock_mc4      = 125000000,
 464                 .espi_nports    = 1,
 465                 .clock_elmer0   = 44,
 466                 .mdio_mdien     = 0,
 467                 .mdio_mdiinv    = 0,
 468                 .mdio_mdc       = 1,
 469                 .mdio_phybaseaddr = 0,
 470                 .gmac           = &t1_pm3393_ops,
 471                 .gphy           = &t1_mv88x201x_ops,
 472                 .mdio_ops       = &mi1_mdio_ext_ops,
 473                 .desc           = "Chelsio T210 1x10GBaseX TOE",
 474         },
 475 
 476         {
 477                 .board          = CHBT_BOARD_CHT210,
 478                 .port_number    = 1,
 479                 .caps           = SUPPORTED_10000baseT_Full,
 480                 .chip_term      = CHBT_TERM_T2,
 481                 .chip_mac       = CHBT_MAC_PM3393,
 482                 .chip_phy       = CHBT_PHY_MY3126,
 483                 .clock_core     = 125000000,
 484                 .clock_mc3      = 133000000,
 485                 .clock_mc4      = 125000000,
 486                 .espi_nports    = 1,
 487                 .clock_elmer0   = 44,
 488                 .mdio_mdien     = 1,
 489                 .mdio_mdiinv    = 1,
 490                 .mdio_mdc       = 1,
 491                 .mdio_phybaseaddr = 1,
 492                 .gmac           = &t1_pm3393_ops,
 493                 .gphy           = &t1_my3126_ops,
 494                 .mdio_ops       = &mi1_mdio_ext_ops,
 495                 .desc           = "Chelsio T210 1x10GBase-CX4 TOE",
 496         },
 497 
 498 #ifdef CONFIG_CHELSIO_T1_1G
 499         {
 500                 .board          = CHBT_BOARD_CHN204,
 501                 .port_number    = 4,
 502                 .caps           = SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full
 503                                 | SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full
 504                                 | SUPPORTED_1000baseT_Full | SUPPORTED_Autoneg |
 505                                   SUPPORTED_PAUSE | SUPPORTED_TP,
 506                 .chip_term      = CHBT_TERM_T2,
 507                 .chip_mac       = CHBT_MAC_VSC7321,
 508                 .chip_phy       = CHBT_PHY_88E1111,
 509                 .clock_core     = 100000000,
 510                 .espi_nports    = 4,
 511                 .clock_elmer0   = 44,
 512                 .mdio_mdien     = 0,
 513                 .mdio_mdiinv    = 0,
 514                 .mdio_mdc       = 0,
 515                 .mdio_phybaseaddr = 4,
 516                 .gmac           = &t1_vsc7326_ops,
 517                 .gphy           = &t1_mv88e1xxx_ops,
 518                 .mdio_ops       = &mi1_mdio_ops,
 519                 .desc           = "Chelsio N204 4x100/1000BaseT NIC",
 520         },
 521 #endif
 522 
 523 };
 524 
 525 const struct pci_device_id t1_pci_tbl[] = {
 526         CH_DEVICE(8, 0, CH_BRD_T110_1CU),
 527         CH_DEVICE(8, 1, CH_BRD_T110_1CU),
 528         CH_DEVICE(7, 0, CH_BRD_N110_1F),
 529         CH_DEVICE(10, 1, CH_BRD_N210_1F),
 530         CH_DEVICE(11, 1, CH_BRD_T210_1F),
 531         CH_DEVICE(14, 1, CH_BRD_T210_1CU),
 532         CH_DEVICE(16, 1, CH_BRD_N204_4CU),
 533         { 0 }
 534 };
 535 
 536 MODULE_DEVICE_TABLE(pci, t1_pci_tbl);
 537 
 538 /*
 539  * Return the board_info structure with a given index.  Out-of-range indices
 540  * return NULL.
 541  */
 542 const struct board_info *t1_get_board_info(unsigned int board_id)
 543 {
 544         return board_id < ARRAY_SIZE(t1_board) ? &t1_board[board_id] : NULL;
 545 }
 546 
 547 struct chelsio_vpd_t {
 548         u32 format_version;
 549         u8 serial_number[16];
 550         u8 mac_base_address[6];
 551         u8 pad[2];           /* make multiple-of-4 size requirement explicit */
 552 };
 553 
 554 #define EEPROMSIZE        (8 * 1024)
 555 #define EEPROM_MAX_POLL   4
 556 
 557 /*
 558  * Read SEEPROM. A zero is written to the flag register when the address is
 559  * written to the Control register. The hardware device will set the flag to a
 560  * one when 4B have been transferred to the Data register.
 561  */
 562 int t1_seeprom_read(adapter_t *adapter, u32 addr, __le32 *data)
 563 {
 564         int i = EEPROM_MAX_POLL;
 565         u16 val;
 566         u32 v;
 567 
 568         if (addr >= EEPROMSIZE || (addr & 3))
 569                 return -EINVAL;
 570 
 571         pci_write_config_word(adapter->pdev, A_PCICFG_VPD_ADDR, (u16)addr);
 572         do {
 573                 udelay(50);
 574                 pci_read_config_word(adapter->pdev, A_PCICFG_VPD_ADDR, &val);
 575         } while (!(val & F_VPD_OP_FLAG) && --i);
 576 
 577         if (!(val & F_VPD_OP_FLAG)) {
 578                 pr_err("%s: reading EEPROM address 0x%x failed\n",
 579                        adapter->name, addr);
 580                 return -EIO;
 581         }
 582         pci_read_config_dword(adapter->pdev, A_PCICFG_VPD_DATA, &v);
 583         *data = cpu_to_le32(v);
 584         return 0;
 585 }
 586 
 587 static int t1_eeprom_vpd_get(adapter_t *adapter, struct chelsio_vpd_t *vpd)
 588 {
 589         int addr, ret = 0;
 590 
 591         for (addr = 0; !ret && addr < sizeof(*vpd); addr += sizeof(u32))
 592                 ret = t1_seeprom_read(adapter, addr,
 593                                       (__le32 *)((u8 *)vpd + addr));
 594 
 595         return ret;
 596 }
 597 
 598 /*
 599  * Read a port's MAC address from the VPD ROM.
 600  */
 601 static int vpd_macaddress_get(adapter_t *adapter, int index, u8 mac_addr[])
 602 {
 603         struct chelsio_vpd_t vpd;
 604 
 605         if (t1_eeprom_vpd_get(adapter, &vpd))
 606                 return 1;
 607         memcpy(mac_addr, vpd.mac_base_address, 5);
 608         mac_addr[5] = vpd.mac_base_address[5] + index;
 609         return 0;
 610 }
 611 
 612 /*
 613  * Set up the MAC/PHY according to the requested link settings.
 614  *
 615  * If the PHY can auto-negotiate first decide what to advertise, then
 616  * enable/disable auto-negotiation as desired and reset.
 617  *
 618  * If the PHY does not auto-negotiate we just reset it.
 619  *
 620  * If auto-negotiation is off set the MAC to the proper speed/duplex/FC,
 621  * otherwise do it later based on the outcome of auto-negotiation.
 622  */
 623 int t1_link_start(struct cphy *phy, struct cmac *mac, struct link_config *lc)
 624 {
 625         unsigned int fc = lc->requested_fc & (PAUSE_RX | PAUSE_TX);
 626 
 627         if (lc->supported & SUPPORTED_Autoneg) {
 628                 lc->advertising &= ~(ADVERTISED_ASYM_PAUSE | ADVERTISED_PAUSE);
 629                 if (fc) {
 630                         if (fc == ((PAUSE_RX | PAUSE_TX) &
 631                                    (mac->adapter->params.nports < 2)))
 632                                 lc->advertising |= ADVERTISED_PAUSE;
 633                         else {
 634                                 lc->advertising |= ADVERTISED_ASYM_PAUSE;
 635                                 if (fc == PAUSE_RX)
 636                                         lc->advertising |= ADVERTISED_PAUSE;
 637                         }
 638                 }
 639                 phy->ops->advertise(phy, lc->advertising);
 640 
 641                 if (lc->autoneg == AUTONEG_DISABLE) {
 642                         lc->speed = lc->requested_speed;
 643                         lc->duplex = lc->requested_duplex;
 644                         lc->fc = (unsigned char)fc;
 645                         mac->ops->set_speed_duplex_fc(mac, lc->speed,
 646                                                       lc->duplex, fc);
 647                         /* Also disables autoneg */
 648                         phy->state = PHY_AUTONEG_RDY;
 649                         phy->ops->set_speed_duplex(phy, lc->speed, lc->duplex);
 650                         phy->ops->reset(phy, 0);
 651                 } else {
 652                         phy->state = PHY_AUTONEG_EN;
 653                         phy->ops->autoneg_enable(phy); /* also resets PHY */
 654                 }
 655         } else {
 656                 phy->state = PHY_AUTONEG_RDY;
 657                 mac->ops->set_speed_duplex_fc(mac, -1, -1, fc);
 658                 lc->fc = (unsigned char)fc;
 659                 phy->ops->reset(phy, 0);
 660         }
 661         return 0;
 662 }
 663 
 664 /*
 665  * External interrupt handler for boards using elmer0.
 666  */
 667 int t1_elmer0_ext_intr_handler(adapter_t *adapter)
 668 {
 669         struct cphy *phy;
 670         int phy_cause;
 671         u32 cause;
 672 
 673         t1_tpi_read(adapter, A_ELMER0_INT_CAUSE, &cause);
 674 
 675         switch (board_info(adapter)->board) {
 676 #ifdef CONFIG_CHELSIO_T1_1G
 677         case CHBT_BOARD_CHT204:
 678         case CHBT_BOARD_CHT204E:
 679         case CHBT_BOARD_CHN204:
 680         case CHBT_BOARD_CHT204V: {
 681                 int i, port_bit;
 682                 for_each_port(adapter, i) {
 683                         port_bit = i + 1;
 684                         if (!(cause & (1 << port_bit)))
 685                                 continue;
 686 
 687                         phy = adapter->port[i].phy;
 688                         phy_cause = phy->ops->interrupt_handler(phy);
 689                         if (phy_cause & cphy_cause_link_change)
 690                                 t1_link_changed(adapter, i);
 691                 }
 692                 break;
 693         }
 694         case CHBT_BOARD_CHT101:
 695                 if (cause & ELMER0_GP_BIT1) { /* Marvell 88E1111 interrupt */
 696                         phy = adapter->port[0].phy;
 697                         phy_cause = phy->ops->interrupt_handler(phy);
 698                         if (phy_cause & cphy_cause_link_change)
 699                                 t1_link_changed(adapter, 0);
 700                 }
 701                 break;
 702         case CHBT_BOARD_7500: {
 703                 int p;
 704                 /*
 705                  * Elmer0's interrupt cause isn't useful here because there is
 706                  * only one bit that can be set for all 4 ports.  This means
 707                  * we are forced to check every PHY's interrupt status
 708                  * register to see who initiated the interrupt.
 709                  */
 710                 for_each_port(adapter, p) {
 711                         phy = adapter->port[p].phy;
 712                         phy_cause = phy->ops->interrupt_handler(phy);
 713                         if (phy_cause & cphy_cause_link_change)
 714                             t1_link_changed(adapter, p);
 715                 }
 716                 break;
 717         }
 718 #endif
 719         case CHBT_BOARD_CHT210:
 720         case CHBT_BOARD_N210:
 721         case CHBT_BOARD_N110:
 722                 if (cause & ELMER0_GP_BIT6) { /* Marvell 88x2010 interrupt */
 723                         phy = adapter->port[0].phy;
 724                         phy_cause = phy->ops->interrupt_handler(phy);
 725                         if (phy_cause & cphy_cause_link_change)
 726                                 t1_link_changed(adapter, 0);
 727                 }
 728                 break;
 729         case CHBT_BOARD_8000:
 730         case CHBT_BOARD_CHT110:
 731                 if (netif_msg_intr(adapter))
 732                         dev_dbg(&adapter->pdev->dev,
 733                                 "External interrupt cause 0x%x\n", cause);
 734                 if (cause & ELMER0_GP_BIT1) {        /* PMC3393 INTB */
 735                         struct cmac *mac = adapter->port[0].mac;
 736 
 737                         mac->ops->interrupt_handler(mac);
 738                 }
 739                 if (cause & ELMER0_GP_BIT5) {        /* XPAK MOD_DETECT */
 740                         u32 mod_detect;
 741 
 742                         t1_tpi_read(adapter,
 743                                         A_ELMER0_GPI_STAT, &mod_detect);
 744                         if (netif_msg_link(adapter))
 745                                 dev_info(&adapter->pdev->dev, "XPAK %s\n",
 746                                          mod_detect ? "removed" : "inserted");
 747                 }
 748                 break;
 749         }
 750         t1_tpi_write(adapter, A_ELMER0_INT_CAUSE, cause);
 751         return 0;
 752 }
 753 
 754 /* Enables all interrupts. */
 755 void t1_interrupts_enable(adapter_t *adapter)
 756 {
 757         unsigned int i;
 758 
 759         adapter->slow_intr_mask = F_PL_INTR_SGE_ERR | F_PL_INTR_TP;
 760 
 761         t1_sge_intr_enable(adapter->sge);
 762         t1_tp_intr_enable(adapter->tp);
 763         if (adapter->espi) {
 764                 adapter->slow_intr_mask |= F_PL_INTR_ESPI;
 765                 t1_espi_intr_enable(adapter->espi);
 766         }
 767 
 768         /* Enable MAC/PHY interrupts for each port. */
 769         for_each_port(adapter, i) {
 770                 adapter->port[i].mac->ops->interrupt_enable(adapter->port[i].mac);
 771                 adapter->port[i].phy->ops->interrupt_enable(adapter->port[i].phy);
 772         }
 773 
 774         /* Enable PCIX & external chip interrupts on ASIC boards. */
 775         if (t1_is_asic(adapter)) {
 776                 u32 pl_intr = readl(adapter->regs + A_PL_ENABLE);
 777 
 778                 /* PCI-X interrupts */
 779                 pci_write_config_dword(adapter->pdev, A_PCICFG_INTR_ENABLE,
 780                                        0xffffffff);
 781 
 782                 adapter->slow_intr_mask |= F_PL_INTR_EXT | F_PL_INTR_PCIX;
 783                 pl_intr |= F_PL_INTR_EXT | F_PL_INTR_PCIX;
 784                 writel(pl_intr, adapter->regs + A_PL_ENABLE);
 785         }
 786 }
 787 
 788 /* Disables all interrupts. */
 789 void t1_interrupts_disable(adapter_t* adapter)
 790 {
 791         unsigned int i;
 792 
 793         t1_sge_intr_disable(adapter->sge);
 794         t1_tp_intr_disable(adapter->tp);
 795         if (adapter->espi)
 796                 t1_espi_intr_disable(adapter->espi);
 797 
 798         /* Disable MAC/PHY interrupts for each port. */
 799         for_each_port(adapter, i) {
 800                 adapter->port[i].mac->ops->interrupt_disable(adapter->port[i].mac);
 801                 adapter->port[i].phy->ops->interrupt_disable(adapter->port[i].phy);
 802         }
 803 
 804         /* Disable PCIX & external chip interrupts. */
 805         if (t1_is_asic(adapter))
 806                 writel(0, adapter->regs + A_PL_ENABLE);
 807 
 808         /* PCI-X interrupts */
 809         pci_write_config_dword(adapter->pdev, A_PCICFG_INTR_ENABLE, 0);
 810 
 811         adapter->slow_intr_mask = 0;
 812 }
 813 
 814 /* Clears all interrupts */
 815 void t1_interrupts_clear(adapter_t* adapter)
 816 {
 817         unsigned int i;
 818 
 819         t1_sge_intr_clear(adapter->sge);
 820         t1_tp_intr_clear(adapter->tp);
 821         if (adapter->espi)
 822                 t1_espi_intr_clear(adapter->espi);
 823 
 824         /* Clear MAC/PHY interrupts for each port. */
 825         for_each_port(adapter, i) {
 826                 adapter->port[i].mac->ops->interrupt_clear(adapter->port[i].mac);
 827                 adapter->port[i].phy->ops->interrupt_clear(adapter->port[i].phy);
 828         }
 829 
 830         /* Enable interrupts for external devices. */
 831         if (t1_is_asic(adapter)) {
 832                 u32 pl_intr = readl(adapter->regs + A_PL_CAUSE);
 833 
 834                 writel(pl_intr | F_PL_INTR_EXT | F_PL_INTR_PCIX,
 835                        adapter->regs + A_PL_CAUSE);
 836         }
 837 
 838         /* PCI-X interrupts */
 839         pci_write_config_dword(adapter->pdev, A_PCICFG_INTR_CAUSE, 0xffffffff);
 840 }
 841 
 842 /*
 843  * Slow path interrupt handler for ASICs.
 844  */
 845 static int asic_slow_intr(adapter_t *adapter)
 846 {
 847         u32 cause = readl(adapter->regs + A_PL_CAUSE);
 848 
 849         cause &= adapter->slow_intr_mask;
 850         if (!cause)
 851                 return 0;
 852         if (cause & F_PL_INTR_SGE_ERR)
 853                 t1_sge_intr_error_handler(adapter->sge);
 854         if (cause & F_PL_INTR_TP)
 855                 t1_tp_intr_handler(adapter->tp);
 856         if (cause & F_PL_INTR_ESPI)
 857                 t1_espi_intr_handler(adapter->espi);
 858         if (cause & F_PL_INTR_PCIX)
 859                 t1_pci_intr_handler(adapter);
 860         if (cause & F_PL_INTR_EXT)
 861                 t1_elmer0_ext_intr(adapter);
 862 
 863         /* Clear the interrupts just processed. */
 864         writel(cause, adapter->regs + A_PL_CAUSE);
 865         readl(adapter->regs + A_PL_CAUSE); /* flush writes */
 866         return 1;
 867 }
 868 
 869 int t1_slow_intr_handler(adapter_t *adapter)
 870 {
 871 #ifdef CONFIG_CHELSIO_T1_1G
 872         if (!t1_is_asic(adapter))
 873                 return fpga_slow_intr(adapter);
 874 #endif
 875         return asic_slow_intr(adapter);
 876 }
 877 
 878 /* Power sequencing is a work-around for Intel's XPAKs. */
 879 static void power_sequence_xpak(adapter_t* adapter)
 880 {
 881         u32 mod_detect;
 882         u32 gpo;
 883 
 884         /* Check for XPAK */
 885         t1_tpi_read(adapter, A_ELMER0_GPI_STAT, &mod_detect);
 886         if (!(ELMER0_GP_BIT5 & mod_detect)) {
 887                 /* XPAK is present */
 888                 t1_tpi_read(adapter, A_ELMER0_GPO, &gpo);
 889                 gpo |= ELMER0_GP_BIT18;
 890                 t1_tpi_write(adapter, A_ELMER0_GPO, gpo);
 891         }
 892 }
 893 
 894 int t1_get_board_rev(adapter_t *adapter, const struct board_info *bi,
 895                      struct adapter_params *p)
 896 {
 897         p->chip_version = bi->chip_term;
 898         p->is_asic = (p->chip_version != CHBT_TERM_FPGA);
 899         if (p->chip_version == CHBT_TERM_T1 ||
 900             p->chip_version == CHBT_TERM_T2 ||
 901             p->chip_version == CHBT_TERM_FPGA) {
 902                 u32 val = readl(adapter->regs + A_TP_PC_CONFIG);
 903 
 904                 val = G_TP_PC_REV(val);
 905                 if (val == 2)
 906                         p->chip_revision = TERM_T1B;
 907                 else if (val == 3)
 908                         p->chip_revision = TERM_T2;
 909                 else
 910                         return -1;
 911         } else
 912                 return -1;
 913         return 0;
 914 }
 915 
 916 /*
 917  * Enable board components other than the Chelsio chip, such as external MAC
 918  * and PHY.
 919  */
 920 static int board_init(adapter_t *adapter, const struct board_info *bi)
 921 {
 922         switch (bi->board) {
 923         case CHBT_BOARD_8000:
 924         case CHBT_BOARD_N110:
 925         case CHBT_BOARD_N210:
 926         case CHBT_BOARD_CHT210:
 927                 t1_tpi_par(adapter, 0xf);
 928                 t1_tpi_write(adapter, A_ELMER0_GPO, 0x800);
 929                 break;
 930         case CHBT_BOARD_CHT110:
 931                 t1_tpi_par(adapter, 0xf);
 932                 t1_tpi_write(adapter, A_ELMER0_GPO, 0x1800);
 933 
 934                 /* TBD XXX Might not need.  This fixes a problem
 935                  *         described in the Intel SR XPAK errata.
 936                  */
 937                 power_sequence_xpak(adapter);
 938                 break;
 939 #ifdef CONFIG_CHELSIO_T1_1G
 940         case CHBT_BOARD_CHT204E:
 941                 /* add config space write here */
 942         case CHBT_BOARD_CHT204:
 943         case CHBT_BOARD_CHT204V:
 944         case CHBT_BOARD_CHN204:
 945                 t1_tpi_par(adapter, 0xf);
 946                 t1_tpi_write(adapter, A_ELMER0_GPO, 0x804);
 947                 break;
 948         case CHBT_BOARD_CHT101:
 949         case CHBT_BOARD_7500:
 950                 t1_tpi_par(adapter, 0xf);
 951                 t1_tpi_write(adapter, A_ELMER0_GPO, 0x1804);
 952                 break;
 953 #endif
 954         }
 955         return 0;
 956 }
 957 
 958 /*
 959  * Initialize and configure the Terminator HW modules.  Note that external
 960  * MAC and PHYs are initialized separately.
 961  */
 962 int t1_init_hw_modules(adapter_t *adapter)
 963 {
 964         int err = -EIO;
 965         const struct board_info *bi = board_info(adapter);
 966 
 967         if (!bi->clock_mc4) {
 968                 u32 val = readl(adapter->regs + A_MC4_CFG);
 969 
 970                 writel(val | F_READY | F_MC4_SLOW, adapter->regs + A_MC4_CFG);
 971                 writel(F_M_BUS_ENABLE | F_TCAM_RESET,
 972                        adapter->regs + A_MC5_CONFIG);
 973         }
 974 
 975         if (adapter->espi && t1_espi_init(adapter->espi, bi->chip_mac,
 976                                           bi->espi_nports))
 977                 goto out_err;
 978 
 979         if (t1_tp_reset(adapter->tp, &adapter->params.tp, bi->clock_core))
 980                 goto out_err;
 981 
 982         err = t1_sge_configure(adapter->sge, &adapter->params.sge);
 983         if (err)
 984                 goto out_err;
 985 
 986         err = 0;
 987 out_err:
 988         return err;
 989 }
 990 
 991 /*
 992  * Determine a card's PCI mode.
 993  */
 994 static void get_pci_mode(adapter_t *adapter, struct chelsio_pci_params *p)
 995 {
 996         static const unsigned short speed_map[] = { 33, 66, 100, 133 };
 997         u32 pci_mode;
 998 
 999         pci_read_config_dword(adapter->pdev, A_PCICFG_MODE, &pci_mode);
1000         p->speed = speed_map[G_PCI_MODE_CLK(pci_mode)];
1001         p->width = (pci_mode & F_PCI_MODE_64BIT) ? 64 : 32;
1002         p->is_pcix = (pci_mode & F_PCI_MODE_PCIX) != 0;
1003 }
1004 
1005 /*
1006  * Release the structures holding the SW per-Terminator-HW-module state.
1007  */
1008 void t1_free_sw_modules(adapter_t *adapter)
1009 {
1010         unsigned int i;
1011 
1012         for_each_port(adapter, i) {
1013                 struct cmac *mac = adapter->port[i].mac;
1014                 struct cphy *phy = adapter->port[i].phy;
1015 
1016                 if (mac)
1017                         mac->ops->destroy(mac);
1018                 if (phy)
1019                         phy->ops->destroy(phy);
1020         }
1021 
1022         if (adapter->sge)
1023                 t1_sge_destroy(adapter->sge);
1024         if (adapter->tp)
1025                 t1_tp_destroy(adapter->tp);
1026         if (adapter->espi)
1027                 t1_espi_destroy(adapter->espi);
1028 }
1029 
1030 static void init_link_config(struct link_config *lc,
1031                              const struct board_info *bi)
1032 {
1033         lc->supported = bi->caps;
1034         lc->requested_speed = lc->speed = SPEED_INVALID;
1035         lc->requested_duplex = lc->duplex = DUPLEX_INVALID;
1036         lc->requested_fc = lc->fc = PAUSE_RX | PAUSE_TX;
1037         if (lc->supported & SUPPORTED_Autoneg) {
1038                 lc->advertising = lc->supported;
1039                 lc->autoneg = AUTONEG_ENABLE;
1040                 lc->requested_fc |= PAUSE_AUTONEG;
1041         } else {
1042                 lc->advertising = 0;
1043                 lc->autoneg = AUTONEG_DISABLE;
1044         }
1045 }
1046 
1047 /*
1048  * Allocate and initialize the data structures that hold the SW state of
1049  * the Terminator HW modules.
1050  */
1051 int t1_init_sw_modules(adapter_t *adapter, const struct board_info *bi)
1052 {
1053         unsigned int i;
1054 
1055         adapter->params.brd_info = bi;
1056         adapter->params.nports = bi->port_number;
1057         adapter->params.stats_update_period = bi->gmac->stats_update_period;
1058 
1059         adapter->sge = t1_sge_create(adapter, &adapter->params.sge);
1060         if (!adapter->sge) {
1061                 pr_err("%s: SGE initialization failed\n",
1062                        adapter->name);
1063                 goto error;
1064         }
1065 
1066         if (bi->espi_nports && !(adapter->espi = t1_espi_create(adapter))) {
1067                 pr_err("%s: ESPI initialization failed\n",
1068                        adapter->name);
1069                 goto error;
1070         }
1071 
1072         adapter->tp = t1_tp_create(adapter, &adapter->params.tp);
1073         if (!adapter->tp) {
1074                 pr_err("%s: TP initialization failed\n",
1075                        adapter->name);
1076                 goto error;
1077         }
1078 
1079         board_init(adapter, bi);
1080         bi->mdio_ops->init(adapter, bi);
1081         if (bi->gphy->reset)
1082                 bi->gphy->reset(adapter);
1083         if (bi->gmac->reset)
1084                 bi->gmac->reset(adapter);
1085 
1086         for_each_port(adapter, i) {
1087                 u8 hw_addr[6];
1088                 struct cmac *mac;
1089                 int phy_addr = bi->mdio_phybaseaddr + i;
1090 
1091                 adapter->port[i].phy = bi->gphy->create(adapter->port[i].dev,
1092                                                         phy_addr, bi->mdio_ops);
1093                 if (!adapter->port[i].phy) {
1094                         pr_err("%s: PHY %d initialization failed\n",
1095                                adapter->name, i);
1096                         goto error;
1097                 }
1098 
1099                 adapter->port[i].mac = mac = bi->gmac->create(adapter, i);
1100                 if (!mac) {
1101                         pr_err("%s: MAC %d initialization failed\n",
1102                                adapter->name, i);
1103                         goto error;
1104                 }
1105 
1106                 /*
1107                  * Get the port's MAC addresses either from the EEPROM if one
1108                  * exists or the one hardcoded in the MAC.
1109                  */
1110                 if (!t1_is_asic(adapter) || bi->chip_mac == CHBT_MAC_DUMMY)
1111                         mac->ops->macaddress_get(mac, hw_addr);
1112                 else if (vpd_macaddress_get(adapter, i, hw_addr)) {
1113                         pr_err("%s: could not read MAC address from VPD ROM\n",
1114                                adapter->port[i].dev->name);
1115                         goto error;
1116                 }
1117                 memcpy(adapter->port[i].dev->dev_addr, hw_addr, ETH_ALEN);
1118                 init_link_config(&adapter->port[i].link_config, bi);
1119         }
1120 
1121         get_pci_mode(adapter, &adapter->params.pci);
1122         t1_interrupts_clear(adapter);
1123         return 0;
1124 
1125 error:
1126         t1_free_sw_modules(adapter);
1127         return -1;
1128 }
/* [<][>][^][v][top][bottom][index][help] */
root/drivers/net/ethernet/chelsio/cxgb/subr.c

DEFINITIONS
