root/arch/x86/pci/broadcom_bus.c

DEFINITIONS

1. cnb20le_res
2. broadcom_postcore_init

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  * Read address ranges from a Broadcom CNB20LE Host Bridge
   4  *
   5  * Copyright (c) 2010 Ira W. Snyder <iws@ovro.caltech.edu>
   6  */
   7 
   8 #include <linux/acpi.h>
   9 #include <linux/delay.h>
  10 #include <linux/dmi.h>
  11 #include <linux/pci.h>
  12 #include <linux/init.h>
  13 #include <asm/pci_x86.h>
  14 #include <asm/pci-direct.h>
  15 
  16 #include "bus_numa.h"
  17 
  18 static void __init cnb20le_res(u8 bus, u8 slot, u8 func)
  19 {
  20         struct pci_root_info *info;
  21         struct pci_root_res *root_res;
  22         struct resource res;
  23         u16 word1, word2;
  24         u8 fbus, lbus;
  25 
  26         /* read the PCI bus numbers */
  27         fbus = read_pci_config_byte(bus, slot, func, 0x44);
  28         lbus = read_pci_config_byte(bus, slot, func, 0x45);
  29         info = alloc_pci_root_info(fbus, lbus, 0, 0);
  30 
  31         /*
  32          * Add the legacy IDE ports on bus 0
  33          *
  34          * These do not exist anywhere in the bridge registers, AFAICT. I do
  35          * not have the datasheet, so this is the best I can do.
  36          */
  37         if (fbus == 0) {
  38                 update_res(info, 0x01f0, 0x01f7, IORESOURCE_IO, 0);
  39                 update_res(info, 0x03f6, 0x03f6, IORESOURCE_IO, 0);
  40                 update_res(info, 0x0170, 0x0177, IORESOURCE_IO, 0);
  41                 update_res(info, 0x0376, 0x0376, IORESOURCE_IO, 0);
  42                 update_res(info, 0xffa0, 0xffaf, IORESOURCE_IO, 0);
  43         }
  44 
  45         /* read the non-prefetchable memory window */
  46         word1 = read_pci_config_16(bus, slot, func, 0xc0);
  47         word2 = read_pci_config_16(bus, slot, func, 0xc2);
  48         if (word1 != word2) {
  49                 res.start = ((resource_size_t) word1 << 16) | 0x0000;
  50                 res.end   = ((resource_size_t) word2 << 16) | 0xffff;
  51                 res.flags = IORESOURCE_MEM;
  52                 update_res(info, res.start, res.end, res.flags, 0);
  53         }
  54 
  55         /* read the prefetchable memory window */
  56         word1 = read_pci_config_16(bus, slot, func, 0xc4);
  57         word2 = read_pci_config_16(bus, slot, func, 0xc6);
  58         if (word1 != word2) {
  59                 res.start = ((resource_size_t) word1 << 16) | 0x0000;
  60                 res.end   = ((resource_size_t) word2 << 16) | 0xffff;
  61                 res.flags = IORESOURCE_MEM | IORESOURCE_PREFETCH;
  62                 update_res(info, res.start, res.end, res.flags, 0);
  63         }
  64 
  65         /* read the IO port window */
  66         word1 = read_pci_config_16(bus, slot, func, 0xd0);
  67         word2 = read_pci_config_16(bus, slot, func, 0xd2);
  68         if (word1 != word2) {
  69                 res.start = word1;
  70                 res.end   = word2;
  71                 res.flags = IORESOURCE_IO;
  72                 update_res(info, res.start, res.end, res.flags, 0);
  73         }
  74 
  75         /* print information about this host bridge */
  76         res.start = fbus;
  77         res.end   = lbus;
  78         res.flags = IORESOURCE_BUS;
  79         printk(KERN_INFO "CNB20LE PCI Host Bridge (domain 0000 %pR)\n", &res);
  80 
  81         list_for_each_entry(root_res, &info->resources, list)
  82                 printk(KERN_INFO "host bridge window %pR\n", &root_res->res);
  83 }
  84 
  85 static int __init broadcom_postcore_init(void)
  86 {
  87         u8 bus = 0, slot = 0;
  88         u32 id;
  89         u16 vendor, device;
  90 
  91 #ifdef CONFIG_ACPI
  92         /*
  93          * We should get host bridge information from ACPI unless the BIOS
  94          * doesn't support it.
  95          */
  96         if (!acpi_disabled && acpi_os_get_root_pointer())
  97                 return 0;
  98 #endif
  99 
 100         id = read_pci_config(bus, slot, 0, PCI_VENDOR_ID);
 101         vendor = id & 0xffff;
 102         device = (id >> 16) & 0xffff;
 103 
 104         if (vendor == PCI_VENDOR_ID_SERVERWORKS &&
 105             device == PCI_DEVICE_ID_SERVERWORKS_LE) {
 106                 cnb20le_res(bus, slot, 0);
 107                 cnb20le_res(bus, slot, 1);
 108         }
 109         return 0;
 110 }
 111 
 112 postcore_initcall(broadcom_postcore_init);