Lines Matching refs:I
12 some cabling tips, and a listing of all jumper settings I can find. Please
26 types, as far as I'm aware, are not compatible and so you cannot wire a
27 100 Mbps card to a 2.5 Mbps card, and so on. From what I hear, my driver does
28 work with 100 Mbps cards, but I haven't been able to verify this myself,
29 since I only have the 2.5 Mbps variety. It is probably not going to saturate
67 level of encapsulation is defined by RFC1201, which I call "packet
95 also work fine, because ARCnet is a very stable network. I personally use 75
130 (Avery's note: oops, I didn't know that. Mine (TV cable) works
256 - the I/O address: this is the "port" your ARCnet card is on. Probed
260 a doc I got from Novell, MS Windows prefers values of 0x300 or more,
304 back side. I take no responsibility if you try this.
365 huge amounts of duplicated information. I have no time to fix it. If you
374 tell me. I had to figure mine out without the manual, and it WASN'T FUN!
458 (I/O and Memory | 1 1 * 0 0 0 0 * 1 1 0 1 |
470 a: The first digit of the I/O address.
478 b: The second digit of the I/O address.
488 The I/O address is in the form ab0. For example, if
568 | Offs|Base |I/O Addr |
593 S1 1-3: I/O Base Address Select
617 Setting the I/O Base Address
621 of eight possible I/O Base addresses using the following table
624 Switch | Hex I/O
724 | node ID is zero | I/O address
747 I have obtained a PC500Longboard and will be doing some experiments on it in
777 < IRQ |I/O Addr |
801 SW1 1-6: I/O Base Address Select
858 Setting the I/O Base Address
862 of 32 possible I/O Base addresses using the following table
864 Switch | Hex I/O
951 | node ID is zero | I/O address
962 cards. However, I'm sure I got 99% of the settings right.
993 I know it works when connected to a PC110 type ARCnet board.
1006 This is a LCS-8830-T made by SMC, I think ('SMC' only appears on one PLCC,
1033 SW2: DIP-Switches for Memory Base and I/O Base addresses
1056 The I/O base address is coded with DIP-Switches 6,7 and 8 of SW2:
1114 - Avery's note: I think PDI508 cards (but definitely NOT PDI508Plus cards)
1127 since it was already there when I got the card. I don't know what
1130 There is a two-jumper array for J3. I don't know what it is for,
1131 but there were already two jumpers on it when I got the card. It's
1189 control the base I/O address of the card.
1191 This was difficult to test by trial and error, and the I/O addresses
1195 the red transmit LED to blink, is the one that I thought works.
1199 blinking. I don't know what 0x3D0 is for though. I recommend using
1204 210 I/O address
1216 (0x100 segment units, or 4k). For example if I set an address of
1224 I recommend using an ARCnet memory address of 0xD000, and putting
1317 6-8: Base I/O Address Select
1374 Setting the I/O Base Address
1378 of eight possible I/O Base addresses using the following table
1381 Switch | Hex I/O
1418 address, but this feature is not documented in the manual and I
1532 SW1 1-6: Base I/O Address Select
1584 Setting the I/O Base Address
1587 The first six switches in switch block SW1 are used to select the I/O Base
1590 Switch | Hex I/O
1662 the time I tried to reach him. Sorry Vlad, if you didn't get my reply.
1691 SW 1 : Shared Memory Address and I/O Base
1707 observe that some of those addresses are unusual and I didn't probe them; I
1709 some others that I didn't write here the card seems to conflict with the
1710 video card (an S3 GENDAC). I leave the full decoding of those addresses to
1713 678| I/O Address
1741 PC100, but has some additional jumpers I don't know the meaning of.
1796 SW1 1-6 Base I/O Address Select
1834 Setting the I/O Base Address
1838 of 32 possible I/O Base addresses using the following tables
1850 The I/O address is sum of all switches set to "1". Remember that
1851 the I/O address space bellow 0x200 is RESERVED for mainboard, so
1894 I know nothing about these. I just guess that J16&J17 are timeout
1896 J11-J15 are connecting IRQ2-7 to some pins on the UFSs. I can't
1907 This is another SMC 90C65-based ARCnet card. I couldn't identify the
1925 | | SW1 | ON | | |I | |
1940 6-8: Base I/O Address Select
1973 Setting the I/O Base Address
1977 of eight possible I/O Base addresses using the following table
1980 Switch | Hex I/O
2055 | |SW1 MEM+I/O| |_________________________| LED1|__|)
2080 6-8 Base I/O Address Select
2113 Setting the I/O Base Address
2117 of eight possible I/O Base addresses using the following table:
2120 Switch | Hex I/O
2193 | Base I/O Base Addr. Station | |
2219 I/O
2256 When I got my two cards, one of them had this switch set to "enhanced". That
2258 card had this switch set to "compatible" and it behaved absolutely normally. I
2265 varies by the type of card involved. I fail to see how either of these
2285 and I tried them again with the "Waterloo" chip removed.
2360 manufacturer didn't put a J1 on the board. The two boards I have both
2384 I have named this ARCnet card "NONAME", since there is no name of any
2423 S2 1-3: I/O Base Address Select
2476 Setting the I/O Base Address
2480 of eight possible I/O Base addresses using the following table
2482 Switch | Hex I/O
2665 Setting the I/O Base Address
2669 of eight possible I/O Base addresses using the following table
2671 Switch | Hex I/O
2756 I have named this ARCnet card "NONAME", since I got only the card with
2773 | |o|o|o|o|o|o|o|o| ON | || I | |
2789 6-8: Base I/O Address Select
2845 Setting the I/O Base Address
2849 of eight possible I/O Base addresses using the following table
2852 Switch | Hex I/O
2957 3-6: I/O Address Map
2960 *I* have had success using RG59B/U with *NO* terminators!
2978 Setting the I/O Base Address
2982 of eight possible I/O Base addresses using the following table
2985 Switch | Hex I/O
3005 I could, however, only verify two settings...
3069 Here is information about my card as far as I could figure it out:
3077 ! ROM 7654321 <- I/O -------
3081 ! : : ! ! !I the Nodenumber
3091 Top Jumper line Bit 7 = ROM Enable 654=Memory location 321=I/O
3104 Settings for I/O Address (Top Jumper Line)
3129 I have no information on other models of ARCnet cards at the moment. Please