Lines Matching refs:pm8001_printk
62 pm8001_printk("TIMEOUT:MEMBASE_II_SHIFT_REGISTER" in pm80xx_bar4_shift()
109 pm8001_printk("forensic_info TYPE_NON_FATAL..............\n")); in pm80xx_get_fatal_dump()
129 PM8001_IO_DBG(pm8001_ha, pm8001_printk("accum_len 0x%x\n", in pm80xx_get_fatal_dump()
133 pm8001_printk("Possible PCI issue 0x%x not expected\n", in pm80xx_get_fatal_dump()
234 pm8001_printk("TIMEOUT:MEMBASE_II_SHIFT_REGISTER" in pm80xx_get_fatal_dump()
710 pm8001_printk(" ila ready status in %d millisec\n", in check_fw_ready()
725 pm8001_printk(" raae ready status in %d millisec\n", in check_fw_ready()
740 pm8001_printk(" iop0 ready status in %d millisec\n", in check_fw_ready()
757 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in check_fw_ready()
778 pm8001_printk("Scratchpad 0 Offset: 0x%x value 0x%x\n", in init_pci_device_addresses()
783 pm8001_printk("Scratchpad 0 PCI BAR: %d\n", pcibar)); in init_pci_device_addresses()
806 pm8001_printk("GST OFFSET 0x%x\n", in init_pci_device_addresses()
809 pm8001_printk("INBND OFFSET 0x%x\n", in init_pci_device_addresses()
812 pm8001_printk("OBND OFFSET 0x%x\n", in init_pci_device_addresses()
815 pm8001_printk("IVT OFFSET 0x%x\n", in init_pci_device_addresses()
818 pm8001_printk("PSPA OFFSET 0x%x\n", in init_pci_device_addresses()
821 pm8001_printk("addr - main cfg %p general status %p\n", in init_pci_device_addresses()
825 pm8001_printk("addr - inbnd %p obnd %p\n", in init_pci_device_addresses()
829 pm8001_printk("addr - pspa %p ivt %p\n", in init_pci_device_addresses()
911 pm8001_printk("SASConfigPage.pageCode " in pm80xx_set_sas_protocol_timer_config()
914 pm8001_printk("SASConfigPage.MST_MSI " in pm80xx_set_sas_protocol_timer_config()
917 pm8001_printk("SASConfigPage.STP_SSP_MCT_TMO " in pm80xx_set_sas_protocol_timer_config()
920 pm8001_printk("SASConfigPage.STP_FRM_TMO " in pm80xx_set_sas_protocol_timer_config()
923 pm8001_printk("SASConfigPage.STP_IDLE_TMO " in pm80xx_set_sas_protocol_timer_config()
926 pm8001_printk("SASConfigPage.OPNRJT_RTRY_INTVL " in pm80xx_set_sas_protocol_timer_config()
929 pm8001_printk("SASConfigPage.Data_Cmd_OPNRJT_RTRY_TMO " in pm80xx_set_sas_protocol_timer_config()
932 pm8001_printk("SASConfigPage.Data_Cmd_OPNRJT_RTRY_THR " in pm80xx_set_sas_protocol_timer_config()
934 PM8001_INIT_DBG(pm8001_ha, pm8001_printk("SASConfigPage.MAX_AIP " in pm80xx_set_sas_protocol_timer_config()
974 PM8001_INIT_DBG(pm8001_ha, pm8001_printk( in pm80xx_get_encrypt_info()
983 PM8001_INIT_DBG(pm8001_ha, pm8001_printk( in pm80xx_get_encrypt_info()
1005 PM8001_INIT_DBG(pm8001_ha, pm8001_printk( in pm80xx_get_encrypt_info()
1028 PM8001_INIT_DBG(pm8001_ha, pm8001_printk( in pm80xx_get_encrypt_info()
1082 pm8001_printk("Firmware is not ready!\n")); in pm80xx_chip_init()
1105 pm8001_printk("MPI initialize successful!\n")); in pm80xx_chip_init()
1115 pm8001_printk("Checking for encryption\n")); in pm80xx_chip_init()
1119 pm8001_printk("Encryption error !!\n")); in pm80xx_chip_init()
1121 PM8001_INIT_DBG(pm8001_ha, pm8001_printk( in pm80xx_chip_init()
1155 pm8001_printk("TIMEOUT:IBDB value/=%x\n", value)); in mpi_uninit_check()
1173 pm8001_printk(" TIME OUT MPI State = 0x%x\n", in mpi_uninit_check()
1197 pm8001_printk("MPI state is not ready\n")); in pm80xx_chip_soft_rst()
1204 pm8001_printk("reset register before write : 0x%x\n", regval)); in pm80xx_chip_soft_rst()
1211 pm8001_printk("reset register after write 0x%x\n", regval)); in pm80xx_chip_soft_rst()
1216 pm8001_printk(" soft reset successful [regval: 0x%x]\n", in pm80xx_chip_soft_rst()
1220 pm8001_printk(" soft reset failed [regval: 0x%x]\n", in pm80xx_chip_soft_rst()
1229 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in pm80xx_chip_soft_rst()
1233 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in pm80xx_chip_soft_rst()
1237 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in pm80xx_chip_soft_rst()
1241 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in pm80xx_chip_soft_rst()
1250 pm8001_printk("Firmware is not ready!\n")); in pm80xx_chip_soft_rst()
1261 pm8001_printk("iButton Feature is" in pm80xx_chip_soft_rst()
1267 pm8001_printk("CRC Check for iButton" in pm80xx_chip_soft_rst()
1274 pm8001_printk("SPCv soft reset Complete\n")); in pm80xx_chip_soft_rst()
1283 pm8001_printk("chip reset start\n")); in pm80xx_hw_chip_rst()
1288 pm8001_printk("SPC soft reset Complete\n")); in pm80xx_hw_chip_rst()
1301 pm8001_printk("chip reset finished\n")); in pm80xx_hw_chip_rst()
1375 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("dev is null\n")); in pm80xx_send_abort_all()
1382 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("cannot " in pm80xx_send_abort_all()
1431 pm8001_printk("cannot allocate task !!!\n")); in pm80xx_send_read_log()
1440 pm8001_printk("cannot allocate tag !!!\n")); in pm80xx_send_read_log()
1452 pm8001_printk("Domain device cannot be allocated\n")); in pm80xx_send_read_log()
1529 pm8001_printk("sas IO status 0x%x\n", status)); in mpi_ssp_completion()
1537 pm8001_printk("SAS Address of IO Failure Drive" in mpi_ssp_completion()
1543 pm8001_printk("IO_SUCCESS ,param = 0x%x\n", in mpi_ssp_completion()
1560 pm8001_printk("IO_ABORTED IOMB Tag\n")); in mpi_ssp_completion()
1567 pm8001_printk("IO_UNDERFLOW ,param = 0x%x\n", in mpi_ssp_completion()
1577 pm8001_printk("IO_NO_DEVICE\n")); in mpi_ssp_completion()
1583 pm8001_printk("IO_XFER_ERROR_BREAK\n")); in mpi_ssp_completion()
1591 pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n")); in mpi_ssp_completion()
1598 pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n")); in mpi_ssp_completion()
1605 pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n")); in mpi_ssp_completion()
1612 pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n")); in mpi_ssp_completion()
1624 pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n")); in mpi_ssp_completion()
1635 pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n")); in mpi_ssp_completion()
1641 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_ssp_completion()
1649 pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n")); in mpi_ssp_completion()
1656 pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n")); in mpi_ssp_completion()
1663 pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n")); in mpi_ssp_completion()
1669 pm8001_printk("IO_XFER_ERROR_DMA\n")); in mpi_ssp_completion()
1675 pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n")); in mpi_ssp_completion()
1682 pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n")); in mpi_ssp_completion()
1688 pm8001_printk("IO_PORT_IN_RESET\n")); in mpi_ssp_completion()
1694 pm8001_printk("IO_DS_NON_OPERATIONAL\n")); in mpi_ssp_completion()
1704 pm8001_printk("IO_DS_IN_RECOVERY\n")); in mpi_ssp_completion()
1710 pm8001_printk("IO_TM_TAG_NOT_FOUND\n")); in mpi_ssp_completion()
1716 pm8001_printk("IO_SSP_EXT_IU_ZERO_LEN_ERROR\n")); in mpi_ssp_completion()
1722 pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n")); in mpi_ssp_completion()
1729 pm8001_printk("Unknown status 0x%x\n", status)); in mpi_ssp_completion()
1736 pm8001_printk("scsi_status = 0x%x\n ", in mpi_ssp_completion()
1744 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk( in mpi_ssp_completion()
1776 pm8001_printk("sas IO status 0x%x\n", event)); in mpi_ssp_event()
1781 pm8001_printk("port_id:0x%x, tag:0x%x, event:0x%x\n", in mpi_ssp_event()
1785 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n");) in mpi_ssp_event()
1794 pm8001_printk("IO_XFER_ERROR_BREAK\n")); in mpi_ssp_event()
1799 pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n")); in mpi_ssp_event()
1805 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_ssp_event()
1813 pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n")); in mpi_ssp_event()
1820 pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n")); in mpi_ssp_event()
1832 pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n")); in mpi_ssp_event()
1843 pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n")); in mpi_ssp_event()
1849 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_ssp_event()
1857 pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n")); in mpi_ssp_event()
1864 pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n")); in mpi_ssp_event()
1871 pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n")); in mpi_ssp_event()
1877 pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n")); in mpi_ssp_event()
1882 pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n")); in mpi_ssp_event()
1888 pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n")); in mpi_ssp_event()
1894 pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n")); in mpi_ssp_event()
1900 pm8001_printk("IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT\n")); in mpi_ssp_event()
1906 pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n")); in mpi_ssp_event()
1912 pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n")); in mpi_ssp_event()
1918 pm8001_printk("IO_XFR_ERROR_INTERNAL_CRC_ERROR\n")); in mpi_ssp_event()
1925 pm8001_printk("IO_XFER_CMD_FRAME_ISSUED\n")); in mpi_ssp_event()
1929 pm8001_printk("Unknown status 0x%x\n", event)); in mpi_ssp_event()
1941 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk( in mpi_ssp_event()
1980 pm8001_printk("tag null\n")); in mpi_sata_completion()
1990 pm8001_printk("ccb null\n")); in mpi_sata_completion()
1999 pm8001_printk("task null\n")); in mpi_sata_completion()
2006 pm8001_printk("task or dev null\n")); in mpi_sata_completion()
2013 pm8001_printk("ts null\n")); in mpi_sata_completion()
2047 pm8001_printk("SAS Address of IO Failure Drive:" in mpi_sata_completion()
2053 pm8001_printk("SAS Address of IO Failure Drive:" in mpi_sata_completion()
2059 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n")); in mpi_sata_completion()
2082 pm8001_printk("SAS_PROTO_RESPONSE len = %d\n", in mpi_sata_completion()
2090 pm8001_printk("PIO read len = %d\n", len)); in mpi_sata_completion()
2094 pm8001_printk("FPDMA len = %d\n", len)); in mpi_sata_completion()
2098 pm8001_printk("other len = %d\n", len)); in mpi_sata_completion()
2106 pm8001_printk("response to large\n")); in mpi_sata_completion()
2113 pm8001_printk("IO_ABORTED IOMB Tag\n")); in mpi_sata_completion()
2123 pm8001_printk("IO_UNDERFLOW param = %d\n", param)); in mpi_sata_completion()
2132 pm8001_printk("IO_NO_DEVICE\n")); in mpi_sata_completion()
2138 pm8001_printk("IO_XFER_ERROR_BREAK\n")); in mpi_sata_completion()
2144 pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n")); in mpi_sata_completion()
2150 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_sata_completion()
2158 pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n")); in mpi_sata_completion()
2165 pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n")); in mpi_sata_completion()
2177 pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n")); in mpi_sata_completion()
2192 pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n")); in mpi_sata_completion()
2207 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_sata_completion()
2214 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_sata_completion()
2230 pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n")); in mpi_sata_completion()
2237 pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n")); in mpi_sata_completion()
2243 pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n")); in mpi_sata_completion()
2249 pm8001_printk("IO_XFER_ERROR_DMA\n")); in mpi_sata_completion()
2255 pm8001_printk("IO_XFER_ERROR_SATA_LINK_TIMEOUT\n")); in mpi_sata_completion()
2261 pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n")); in mpi_sata_completion()
2267 pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n")); in mpi_sata_completion()
2273 pm8001_printk("IO_PORT_IN_RESET\n")); in mpi_sata_completion()
2279 pm8001_printk("IO_DS_NON_OPERATIONAL\n")); in mpi_sata_completion()
2293 pm8001_printk("IO_DS_IN_RECOVERY\n")); in mpi_sata_completion()
2299 pm8001_printk("IO_DS_IN_ERROR\n")); in mpi_sata_completion()
2313 pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n")); in mpi_sata_completion()
2319 pm8001_printk("Unknown status 0x%x\n", status)); in mpi_sata_completion()
2332 pm8001_printk("task 0x%p done with io_status 0x%x" in mpi_sata_completion()
2364 pm8001_printk("No CCB !!!. returning\n")); in mpi_sata_event()
2369 pm8001_printk("SATA EVENT 0x%x\n", event)); in mpi_sata_event()
2383 pm8001_printk("task or dev null\n")); in mpi_sata_event()
2389 pm8001_printk("port_id:0x%x, tag:0x%x, event:0x%x\n", in mpi_sata_event()
2393 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n")); in mpi_sata_event()
2402 pm8001_printk("IO_XFER_ERROR_BREAK\n")); in mpi_sata_event()
2408 pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n")); in mpi_sata_event()
2414 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_sata_event()
2422 pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n")); in mpi_sata_event()
2429 pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n")); in mpi_sata_event()
2441 pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n")); in mpi_sata_event()
2456 pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n")); in mpi_sata_event()
2462 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_sata_event()
2470 pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n")); in mpi_sata_event()
2477 pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n")); in mpi_sata_event()
2483 pm8001_printk("IO_XFER_ERROR_PEER_ABORTED\n")); in mpi_sata_event()
2489 pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n")); in mpi_sata_event()
2495 pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n")); in mpi_sata_event()
2501 pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n")); in mpi_sata_event()
2507 pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n")); in mpi_sata_event()
2513 pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n")); in mpi_sata_event()
2519 pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n")); in mpi_sata_event()
2525 pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n")); in mpi_sata_event()
2531 pm8001_printk("IO_XFER_CMD_FRAME_ISSUED\n")); in mpi_sata_event()
2535 pm8001_printk("IO_XFER_PIO_SETUP_ERROR\n")); in mpi_sata_event()
2541 pm8001_printk("IO_XFR_ERROR_INTERNAL_CRC_ERROR\n")); in mpi_sata_event()
2548 pm8001_printk("IO_XFR_DMA_ACTIVATE_TIMEOUT\n")); in mpi_sata_event()
2555 pm8001_printk("Unknown status 0x%x\n", event)); in mpi_sata_event()
2568 pm8001_printk("task 0x%p done with io_status 0x%x" in mpi_sata_event()
2604 pm8001_printk("smp IO status 0x%x\n", status)); in mpi_smp_completion()
2611 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n")); in mpi_smp_completion()
2618 pm8001_printk("DIRECT RESPONSE Length:%d\n", in mpi_smp_completion()
2625 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_smp_completion()
2634 pm8001_printk("IO_ABORTED IOMB\n")); in mpi_smp_completion()
2641 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n")); in mpi_smp_completion()
2649 PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_NO_DEVICE\n")); in mpi_smp_completion()
2655 pm8001_printk("IO_ERROR_HW_TIMEOUT\n")); in mpi_smp_completion()
2661 pm8001_printk("IO_XFER_ERROR_BREAK\n")); in mpi_smp_completion()
2667 pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n")); in mpi_smp_completion()
2673 pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n")); in mpi_smp_completion()
2680 pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n")); in mpi_smp_completion()
2687 pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n")); in mpi_smp_completion()
2699 pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n")); in mpi_smp_completion()
2709 pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n")); in mpi_smp_completion()
2715 PM8001_IO_DBG(pm8001_ha, pm8001_printk(\ in mpi_smp_completion()
2723 pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n")); in mpi_smp_completion()
2730 pm8001_printk("IO_XFER_ERROR_RX_FRAME\n")); in mpi_smp_completion()
2736 pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n")); in mpi_smp_completion()
2743 pm8001_printk("IO_ERROR_INTERNAL_SMP_RESOURCE\n")); in mpi_smp_completion()
2749 pm8001_printk("IO_PORT_IN_RESET\n")); in mpi_smp_completion()
2756 pm8001_printk("IO_DS_NON_OPERATIONAL\n")); in mpi_smp_completion()
2762 pm8001_printk("IO_DS_IN_RECOVERY\n")); in mpi_smp_completion()
2769 pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n")); in mpi_smp_completion()
2776 pm8001_printk("Unknown status 0x%x\n", status)); in mpi_smp_completion()
2788 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk( in mpi_smp_completion()
2860 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in hw_event_sas_phy_up()
2868 pm8001_printk("device type no device.\n")); in hw_event_sas_phy_up()
2871 PM8001_MSG_DBG(pm8001_ha, pm8001_printk("end device.\n")); in hw_event_sas_phy_up()
2879 pm8001_printk("expander device.\n")); in hw_event_sas_phy_up()
2885 pm8001_printk("fanout expander device.\n")); in hw_event_sas_phy_up()
2891 pm8001_printk("unknown device type(%x)\n", deviceType)); in hw_event_sas_phy_up()
2939 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in hw_event_sata_phy_up()
2993 pm8001_printk(" PortInvalid portID %d\n", port_id)); in hw_event_phy_down()
2995 pm8001_printk(" Last phy Down and port invalid\n")); in hw_event_phy_down()
3002 pm8001_printk(" Port In Reset portID %d\n", port_id)); in hw_event_phy_down()
3006 pm8001_printk(" phy Down and PORT_NOT_ESTABLISHED\n")); in hw_event_phy_down()
3011 pm8001_printk(" phy Down and PORT_LOSTCOMM\n")); in hw_event_phy_down()
3013 pm8001_printk(" Last phy Down and port invalid\n")); in hw_event_phy_down()
3021 pm8001_printk(" phy Down and(default) = 0x%x\n", in hw_event_phy_down()
3039 pm8001_printk("phy start resp status:0x%x, phyid:0x%x\n", in mpi_phy_start_resp()
3064 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_thermal_hw_event()
3066 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_thermal_hw_event()
3071 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_thermal_hw_event()
3073 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in mpi_thermal_hw_event()
3105 pm8001_printk("portid:%d phyid:%d event:0x%x status:0x%x\n", in mpi_hw_event()
3112 pm8001_printk("HW_EVENT_PHY_START_STATUS\n")); in mpi_hw_event()
3117 pm8001_printk("HW_EVENT_SATA_PHY_UP\n")); in mpi_hw_event()
3122 pm8001_printk("HW_EVENT_SATA_SPINUP_HOLD\n")); in mpi_hw_event()
3127 pm8001_printk("HW_EVENT_PHY_DOWN\n")); in mpi_hw_event()
3135 pm8001_printk("HW_EVENT_PORT_INVALID\n")); in mpi_hw_event()
3144 pm8001_printk("HW_EVENT_BROADCAST_CHANGE\n")); in mpi_hw_event()
3154 pm8001_printk("HW_EVENT_PHY_ERROR\n")); in mpi_hw_event()
3161 pm8001_printk("HW_EVENT_BROADCAST_EXP\n")); in mpi_hw_event()
3169 pm8001_printk("HW_EVENT_LINK_ERR_INVALID_DWORD\n")); in mpi_hw_event()
3178 pm8001_printk("HW_EVENT_LINK_ERR_DISPARITY_ERROR\n")); in mpi_hw_event()
3188 pm8001_printk("HW_EVENT_LINK_ERR_CODE_VIOLATION\n")); in mpi_hw_event()
3197 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in mpi_hw_event()
3208 pm8001_printk("HW_EVENT_MALFUNCTION\n")); in mpi_hw_event()
3212 pm8001_printk("HW_EVENT_BROADCAST_SES\n")); in mpi_hw_event()
3220 pm8001_printk("HW_EVENT_INBOUND_CRC_ERROR\n")); in mpi_hw_event()
3227 pm8001_printk("HW_EVENT_HARD_RESET_RECEIVED\n")); in mpi_hw_event()
3232 pm8001_printk("HW_EVENT_ID_FRAME_TIMEOUT\n")); in mpi_hw_event()
3239 pm8001_printk("HW_EVENT_LINK_ERR_PHY_RESET_FAILED\n")); in mpi_hw_event()
3249 pm8001_printk("HW_EVENT_PORT_RESET_TIMER_TMO\n")); in mpi_hw_event()
3256 pm8001_printk("HW_EVENT_PORT_RECOVERY_TIMER_TMO\n")); in mpi_hw_event()
3266 pm8001_printk("HW_EVENT_PORT_RECOVER\n")); in mpi_hw_event()
3270 pm8001_printk("HW_EVENT_PORT_RESET_COMPLETE\n")); in mpi_hw_event()
3274 pm8001_printk("EVENT_BROADCAST_ASYNCH_EVENT\n")); in mpi_hw_event()
3278 pm8001_printk("Unknown event type 0x%x\n", eventType)); in mpi_hw_event()
3299 pm8001_printk("phy:0x%x status:0x%x\n", in mpi_phy_stop_resp()
3319 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in mpi_set_controller_config_resp()
3335 pm8001_printk(" pm80xx_addition_functionality\n")); in mpi_get_controller_config_resp()
3349 pm8001_printk(" pm80xx_addition_functionality\n")); in mpi_get_phy_profile_resp()
3362 pm8001_printk(" pm80xx_addition_functionality\n")); in mpi_flash_op_ext_resp()
3385 pm8001_printk("PhyProfile command failed with status " in mpi_set_phy_profile_resp()
3391 pm8001_printk("Invalid page code 0x%X\n", in mpi_set_phy_profile_resp()
3413 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in mpi_kek_management_resp()
3429 pm8001_printk(" pm80xx_addition_functionality\n")); in mpi_dek_management_resp()
3443 pm8001_printk(" pm80xx_addition_functionality\n")); in ssp_coalesced_comp_resp()
3460 PM8001_MSG_DBG(pm8001_ha, pm8001_printk("OPC_OUB_ECHO\n")); in process_one_iomb()
3464 pm8001_printk("OPC_OUB_HW_EVENT\n")); in process_one_iomb()
3469 pm8001_printk("OPC_OUB_THERMAL_EVENT\n")); in process_one_iomb()
3474 pm8001_printk("OPC_OUB_SSP_COMP\n")); in process_one_iomb()
3479 pm8001_printk("OPC_OUB_SMP_COMP\n")); in process_one_iomb()
3484 pm8001_printk("OPC_OUB_LOCAL_PHY_CNTRL\n")); in process_one_iomb()
3489 pm8001_printk("OPC_OUB_DEV_REGIST\n")); in process_one_iomb()
3494 pm8001_printk("unregister the device\n")); in process_one_iomb()
3499 pm8001_printk("OPC_OUB_GET_DEV_HANDLE\n")); in process_one_iomb()
3503 pm8001_printk("OPC_OUB_SATA_COMP\n")); in process_one_iomb()
3508 pm8001_printk("OPC_OUB_SATA_EVENT\n")); in process_one_iomb()
3513 pm8001_printk("OPC_OUB_SSP_EVENT\n")); in process_one_iomb()
3518 pm8001_printk("OPC_OUB_DEV_HANDLE_ARRIV\n")); in process_one_iomb()
3523 pm8001_printk("OPC_OUB_SSP_RECV_EVENT\n")); in process_one_iomb()
3528 pm8001_printk("OPC_OUB_FW_FLASH_UPDATE\n")); in process_one_iomb()
3533 pm8001_printk("OPC_OUB_GPIO_RESPONSE\n")); in process_one_iomb()
3537 pm8001_printk("OPC_OUB_GPIO_EVENT\n")); in process_one_iomb()
3541 pm8001_printk("OPC_OUB_GENERAL_EVENT\n")); in process_one_iomb()
3546 pm8001_printk("OPC_OUB_SSP_ABORT_RSP\n")); in process_one_iomb()
3551 pm8001_printk("OPC_OUB_SATA_ABORT_RSP\n")); in process_one_iomb()
3556 pm8001_printk("OPC_OUB_SAS_DIAG_MODE_START_END\n")); in process_one_iomb()
3560 pm8001_printk("OPC_OUB_SAS_DIAG_EXECUTE\n")); in process_one_iomb()
3564 pm8001_printk("OPC_OUB_GET_TIME_STAMP\n")); in process_one_iomb()
3568 pm8001_printk("OPC_OUB_SAS_HW_EVENT_ACK\n")); in process_one_iomb()
3572 pm8001_printk("OPC_OUB_PORT_CONTROL\n")); in process_one_iomb()
3576 pm8001_printk("OPC_OUB_SMP_ABORT_RSP\n")); in process_one_iomb()
3581 pm8001_printk("OPC_OUB_GET_NVMD_DATA\n")); in process_one_iomb()
3586 pm8001_printk("OPC_OUB_SET_NVMD_DATA\n")); in process_one_iomb()
3591 pm8001_printk("OPC_OUB_DEVICE_HANDLE_REMOVAL\n")); in process_one_iomb()
3595 pm8001_printk("OPC_OUB_SET_DEVICE_STATE\n")); in process_one_iomb()
3600 pm8001_printk("OPC_OUB_GET_DEVICE_STATE\n")); in process_one_iomb()
3604 pm8001_printk("OPC_OUB_SET_DEV_INFO\n")); in process_one_iomb()
3608 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in process_one_iomb()
3613 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in process_one_iomb()
3618 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in process_one_iomb()
3623 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in process_one_iomb()
3628 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in process_one_iomb()
3633 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in process_one_iomb()
3638 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in process_one_iomb()
3643 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in process_one_iomb()
3648 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in process_one_iomb()
3653 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in process_one_iomb()
3658 PM8001_MSG_DBG(pm8001_ha, pm8001_printk( in process_one_iomb()
3768 pm8001_printk("SMP Frame Length %d\n", sg_req->length)); in pm80xx_chip_smp_req()
3781 pm8001_printk("SMP REQUEST INDIRECT MODE\n")); in pm80xx_chip_smp_req()
3814 pm8001_printk("SMP REQUEST DIRECT MODE\n")); in pm80xx_chip_smp_req()
3818 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in pm80xx_chip_smp_req()
3824 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in pm80xx_chip_smp_req()
3923 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in pm80xx_chip_ssp_io_req()
3957 pm8001_printk("The sg list address " in pm80xx_chip_ssp_io_req()
3988 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in pm80xx_chip_ssp_io_req()
4016 pm8001_printk("The sg list address " in pm80xx_chip_ssp_io_req()
4070 PM8001_IO_DBG(pm8001_ha, pm8001_printk("no data\n")); in pm80xx_chip_sata_req()
4074 PM8001_IO_DBG(pm8001_ha, pm8001_printk("DMA\n")); in pm80xx_chip_sata_req()
4077 PM8001_IO_DBG(pm8001_ha, pm8001_printk("PIO\n")); in pm80xx_chip_sata_req()
4082 PM8001_IO_DBG(pm8001_ha, pm8001_printk("FPDMA\n")); in pm80xx_chip_sata_req()
4102 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in pm80xx_chip_sata_req()
4134 pm8001_printk("The sg list address " in pm80xx_chip_sata_req()
4170 PM8001_IO_DBG(pm8001_ha, pm8001_printk( in pm80xx_chip_sata_req()
4200 pm8001_printk("The sg list address " in pm80xx_chip_sata_req()
4267 pm8001_printk("task 0x%p resp 0x%x " in pm80xx_chip_sata_req()
4306 pm8001_printk("PHY START REQ for phy_id %d\n", phy_id)); in pm80xx_chip_phy_start_req()
4496 PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("Invalid tag\n")); in mpi_set_phy_profile_req()
4501 pm8001_printk(" phy profile command for phy %x ,length is %d\n", in mpi_set_phy_profile_req()
4523 PM8001_INIT_DBG(pm8001_ha, pm8001_printk("phy settings completed\n")); in pm8001_set_phy_profile()