Lines Matching refs:as
37 Say Y here if you wish to use an AMBA PrimeCell UART as the system
42 (/dev/tty0) will still be used as the system console by default, but
43 you can alter that using a kernel command line option such as
65 Say Y here if you wish to use an AMBA PrimeCell UART as the system
70 (/dev/tty0) will still be used as the system console by default, but
71 you can alter that using a kernel command line option such as
100 If unsure, say Y. To compile this driver as a module, choose M here:
109 If you say Y here, it will be possible to use a serial port as the
131 AT91 or AT32 processor as the system console (the system
151 bool "Install as device ttyATn instead of ttySn"
155 appear as /dev/ttyATn (major 204, minor starting at 154)
157 64). This is necessary if you also want other UARTs, such as
172 as a normal console (assuming that the port is attached to KGDB).
198 Say Y here if you wish to use a KS8695 (Centaur) UART as the
216 Say Y here if you wish to use a Amlogic MesonX UART as the
219 logins in single user mode) as /dev/ttyAMLx.
236 (/dev/tty0) will still be used as the system console by default, but
237 you can alter that using a kernel command line option such as
271 generally being used as a console, we use our own output
281 Allow selection of the S3C24XX on-board serial ports for use as
285 (/dev/tty0) will still be used as the system console by default, but
286 you can alter that using a kernel command line option such as
307 (/dev/tty0) will still be used as the system console by default, but
308 you can alter that using a kernel command line option such as
360 If you say Y here, it will be possible to use a serial port as the
365 Note that the firmware uses ttyS3 as the serial console on
381 If unsure, say Y. To compile this driver as a module, choose M here:
390 If you say Y here, it will be possible to use a serial port as the
395 Note that the firmware uses ttyS1 as the serial console on the
418 (/dev/tty0) will still be used as the system console by default, but
419 you can alter that using a kernel command line option such as
455 (/dev/tty0) will still be used as the system console by default, but
456 you can alter that using a kernel command line option such as
480 (/dev/tty0) will still be used as the system console by default, but
481 you can alter that using a kernel command line option such as
494 To compile this driver as a module, choose M here: the
590 (/dev/tty0) will still be used as the system console by default, but
591 you can alter that using a kernel command line option such as
602 To compile this driver as a module, choose M here: the
610 Say Y here if you wish to use a Xilinx uartlite as the system
633 on your Sparc system as the console, you can do so by answering
649 on your Sparc system as the console, you can do so by answering
667 3. Add device ttyB0 to /etc/securetty (if you want to log on as
683 used as the system console. This is useful for machines in
689 3. Add device ttyB0 to /etc/securetty (if you want to log on as
706 on your Sparc system as the console, you can do so by answering
753 If you have a MIPS-based Philips SoC such as PNX8330 and you want
761 If you have a MIPS-based Philips SoC such as PNX8330 and you want
780 ports on the LPC32XX as the console, you can do so by answering
853 be registered as ttyS0 onwards as in the past, and you will be
858 to appear as /dev/ttySn.
866 on your (Power)Mac as the console, you can do so by answering
882 Say Y here if you wish to use a SCC or SMC CPM UART as the system
887 (/dev/tty0) will still be used as the system console by default, but
888 you can alter that using a kernel command line option such as
900 controller serial port as your console (you want this!),
910 for use as console, it must be included in kernel and not as a
919 of the Freescale MPC52xx family as a console.
940 This driver can also be built as a module. If so, the module
992 bool "TX39XX/49XX SIO act as standard serial"
1025 To compile this driver as a module, choose M here: the
1084 To compile this driver as a module, choose M here: the
1122 Select this option if you would like to use omap serial port as
1126 (/dev/tty0) will still be used as the system console by default, but
1127 you can alter that using a kernel command line option such as
1199 To compile this driver as a module, choose M here: the
1363 Enabling PCH_DMA, this PCH UART works as DMA mode.
1377 Say Y here if you wish to use the PCH UART as the system console
1428 To compile this driver as a module, choose M here: the
1502 To compile this driver as a module, choose M here: the
1571 This driver can also be build as a module. If so, the module will be called