| /linux-4.1.27/drivers/net/ethernet/chelsio/cxgb/ |
| D | mv88e1xxx.h | 5 #ifndef BMCR_SPEED1000
6 # define BMCR_SPEED1000 0x40 macro
|
| D | mv88e1xxx.c | 130 ctl &= ~(BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE); in mv88e1xxx_set_speed_duplex()
134 ctl |= BMCR_SPEED1000; in mv88e1xxx_set_speed_duplex()
141 if (ctl & BMCR_SPEED1000) /* auto-negotiation required for 1Gb/s */ in mv88e1xxx_set_speed_duplex()
|
| /linux-4.1.27/include/uapi/linux/ |
| D | mdio.h | 74 #define MDIO_CTRL1_SPEEDSELEXT (BMCR_SPEED1000 | BMCR_SPEED100)
81 #define MDIO_PMA_CTRL1_SPEED1000 BMCR_SPEED1000
|
| D | mii.h | 41 #define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */ macro
|
| /linux-4.1.27/drivers/net/ethernet/ibm/emac/ |
| D | phy.c | 122 ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE); in genmii_setup_aneg()
180 ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE); in genmii_setup_forced()
193 ctl |= BMCR_SPEED1000; in genmii_setup_forced()
266 if (bmcr & BMCR_SPEED1000) in genmii_read_link()
|
| /linux-4.1.27/drivers/net/ |
| D | mii.c | 122 ((bmcr & BMCR_SPEED1000 && in mii_ethtool_gset()
211 BMCR_SPEED1000 | BMCR_FULLDPLX); in mii_ethtool_sset()
213 tmp |= BMCR_SPEED1000; in mii_ethtool_sset()
|
| /linux-4.1.27/drivers/net/phy/ |
| D | et1011c.c | 58 ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_SPEED1000 | in et1011c_config_aneg()
|
| D | fixed_phy.c | 65 bmcr |= BMCR_SPEED1000; in fixed_phy_update_regs()
85 bmcr |= BMCR_SPEED1000; in fixed_phy_update_regs()
|
| D | lxt.c | 229 if (bmcr & BMCR_SPEED1000) in lxt973a2_read_status()
|
| D | phy_device.c | 827 ctl |= BMCR_SPEED1000; in genphy_setup_forced()
1038 if (bmcr & BMCR_SPEED1000) in genphy_read_status()
|
| D | phy.c | 398 if (val & BMCR_SPEED1000) in phy_mii_ioctl()
|
| D | marvell.c | 805 if (bmcr & BMCR_SPEED1000) in marvell_read_status()
|
| /linux-4.1.27/drivers/net/ethernet/chelsio/cxgb3/ |
| D | vsc8211.c | 156 if (bmcr & BMCR_SPEED1000) in vsc8211_get_link_status()
232 if (bmcr & BMCR_SPEED1000) in vsc8211_get_link_status_fiber()
|
| D | t3_hw.c | 459 ctl &= ~(BMCR_SPEED100 | BMCR_SPEED1000 | BMCR_ANENABLE); in t3_set_phy_speed_duplex()
463 ctl |= BMCR_SPEED1000; in t3_set_phy_speed_duplex()
470 if (ctl & BMCR_SPEED1000) /* auto-negotiation required for GigE */ in t3_set_phy_speed_duplex()
|
| /linux-4.1.27/drivers/net/ethernet/dlink/ |
| D | dl2k.c | 1456 switch (bmcr & (BMCR_SPEED100 | BMCR_SPEED1000)) { in mii_get_media()
1457 case BMCR_SPEED1000: in mii_get_media()
|
| /linux-4.1.27/drivers/net/ethernet/intel/e1000e/ |
| D | phy.c | 1470 *phy_ctrl &= ~BMCR_SPEED1000; in e1000e_phy_force_speed_duplex_setup()
1474 *phy_ctrl &= ~(BMCR_SPEED1000 | BMCR_SPEED100); in e1000e_phy_force_speed_duplex_setup()
|
| D | netdev.c | 4826 phy->bmcr = (BMCR_SPEED1000 | BMCR_ANENABLE | BMCR_FULLDPLX); in e1000_phy_read_status()
|
| /linux-4.1.27/drivers/net/ethernet/ |
| D | jme.c | 444 phylink |= ((bmcr & BMCR_SPEED1000) && in jme_check_link()
1903 BMCR_SPEED1000 | BMCR_FULLDPLX); in jme_set_100m_half()
2717 (val & BMCR_SPEED1000)) in jme_ioctl()
|
| /linux-4.1.27/drivers/net/ethernet/broadcom/ |
| D | bnx2.c | 1518 bmcr |= BMCR_SPEED1000 | BMCR_ANENABLE | BMCR_ANRESTART; in bnx2_disable_forced_2g5()
1765 new_bmcr |= BMCR_SPEED1000; in bnx2_setup_serdes_phy()
2438 BMCR_SPEED1000); in bnx2_set_phy_loopback()
6076 bmcr |= BMCR_SPEED1000 | BMCR_FULLDPLX; in bnx2_5706_serdes_timer()
|
| D | tg3.c | 2572 BMCR_FULLDPLX | BMCR_SPEED1000); in tg3_phy_reset_5703_4_5()
4469 bmcr |= BMCR_SPEED1000; in tg3_phy_copper_begin()
4513 switch (val & (BMCR_SPEED1000 | BMCR_SPEED100)) { in tg3_phy_pull_config()
4526 case BMCR_SPEED1000: in tg3_phy_pull_config()
5904 bmcr &= ~BMCR_SPEED1000; in tg3_setup_fiber_mii_phy()
5914 new_bmcr |= BMCR_SPEED1000; in tg3_setup_fiber_mii_phy()
6032 bmcr |= BMCR_SPEED1000 | BMCR_FULLDPLX; in tg3_serdes_parallel_detect()
8203 bmcr |= BMCR_SPEED1000; in tg3_phy_lpbk_set()
|
| /linux-4.1.27/drivers/net/ethernet/sun/ |
| D | niu.c | 1184 if ((bmcr & BMCR_SPEED1000) && !(bmcr & BMCR_SPEED100)) in link_status_mii()
1712 bmcr = (BMCR_SPEED1000 | BMCR_FULLDPLX); in xcvr_init_1g_rgmii()
1761 bmcr |= BMCR_SPEED1000; in mii_init_common()
1829 bmcr |= BMCR_SPEED1000; in mii_init_common()
|
| /linux-4.1.27/drivers/net/ethernet/via/ |
| D | via-velocity.c | 919 MII_REG_BITS_ON(BMCR_SPEED1000, MII_BMCR, vptr->mac_regs); in velocity_set_media_mode()
|
| /linux-4.1.27/drivers/net/ethernet/nvidia/ |
| D | forcedeth.c | 4467 bmcr &= ~(BMCR_ANENABLE|BMCR_SPEED100|BMCR_SPEED1000|BMCR_FULLDPLX); in nv_set_settings()
4784 miicontrol |= BMCR_LOOPBACK | BMCR_FULLDPLX | BMCR_SPEED1000; in nv_set_loopback()
|
| /linux-4.1.27/drivers/net/ethernet/freescale/ |
| D | gianfar.c | 1795 BMCR_SPEED1000); in gfar_configure_serdes()
|
| /linux-4.1.27/drivers/net/usb/ |
| D | r8152.c | 2809 bmcr = BMCR_SPEED1000; in rtl8152_set_speed()
|