1/* 2 * AppliedMicro X-Gene SoC SATA Host Controller Driver 3 * 4 * Copyright (c) 2014, Applied Micro Circuits Corporation 5 * Author: Loc Ho <lho@apm.com> 6 * Tuan Phan <tphan@apm.com> 7 * Suman Tripathi <stripathi@apm.com> 8 * 9 * This program is free software; you can redistribute it and/or modify it 10 * under the terms of the GNU General Public License as published by the 11 * Free Software Foundation; either version 2 of the License, or (at your 12 * option) any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program. If not, see <http://www.gnu.org/licenses/>. 21 * 22 * NOTE: PM support is not currently available. 23 * 24 */ 25#include <linux/acpi.h> 26#include <linux/module.h> 27#include <linux/platform_device.h> 28#include <linux/ahci_platform.h> 29#include <linux/of_address.h> 30#include <linux/of_irq.h> 31#include <linux/phy/phy.h> 32#include "ahci.h" 33 34#define DRV_NAME "xgene-ahci" 35 36/* Max # of disk per a controller */ 37#define MAX_AHCI_CHN_PERCTR 2 38 39/* MUX CSR */ 40#define SATA_ENET_CONFIG_REG 0x00000000 41#define CFG_SATA_ENET_SELECT_MASK 0x00000001 42 43/* SATA core host controller CSR */ 44#define SLVRDERRATTRIBUTES 0x00000000 45#define SLVWRERRATTRIBUTES 0x00000004 46#define MSTRDERRATTRIBUTES 0x00000008 47#define MSTWRERRATTRIBUTES 0x0000000c 48#define BUSCTLREG 0x00000014 49#define IOFMSTRWAUX 0x00000018 50#define INTSTATUSMASK 0x0000002c 51#define ERRINTSTATUS 0x00000030 52#define ERRINTSTATUSMASK 0x00000034 53 54/* SATA host AHCI CSR */ 55#define PORTCFG 0x000000a4 56#define PORTADDR_SET(dst, src) \ 57 (((dst) & ~0x0000003f) | (((u32)(src)) & 0x0000003f)) 58#define PORTPHY1CFG 0x000000a8 59#define PORTPHY1CFG_FRCPHYRDY_SET(dst, src) \ 60 (((dst) & ~0x00100000) | (((u32)(src) << 0x14) & 0x00100000)) 61#define PORTPHY2CFG 0x000000ac 62#define PORTPHY3CFG 0x000000b0 63#define PORTPHY4CFG 0x000000b4 64#define PORTPHY5CFG 0x000000b8 65#define SCTL0 0x0000012C 66#define PORTPHY5CFG_RTCHG_SET(dst, src) \ 67 (((dst) & ~0xfff00000) | (((u32)(src) << 0x14) & 0xfff00000)) 68#define PORTAXICFG_EN_CONTEXT_SET(dst, src) \ 69 (((dst) & ~0x01000000) | (((u32)(src) << 0x18) & 0x01000000)) 70#define PORTAXICFG 0x000000bc 71#define PORTAXICFG_OUTTRANS_SET(dst, src) \ 72 (((dst) & ~0x00f00000) | (((u32)(src) << 0x14) & 0x00f00000)) 73#define PORTRANSCFG 0x000000c8 74#define PORTRANSCFG_RXWM_SET(dst, src) \ 75 (((dst) & ~0x0000007f) | (((u32)(src)) & 0x0000007f)) 76 77/* SATA host controller AXI CSR */ 78#define INT_SLV_TMOMASK 0x00000010 79 80/* SATA diagnostic CSR */ 81#define CFG_MEM_RAM_SHUTDOWN 0x00000070 82#define BLOCK_MEM_RDY 0x00000074 83 84/* Max retry for link down */ 85#define MAX_LINK_DOWN_RETRY 3 86 87struct xgene_ahci_context { 88 struct ahci_host_priv *hpriv; 89 struct device *dev; 90 u8 last_cmd[MAX_AHCI_CHN_PERCTR]; /* tracking the last command issued*/ 91 u32 class[MAX_AHCI_CHN_PERCTR]; /* tracking the class of device */ 92 void __iomem *csr_core; /* Core CSR address of IP */ 93 void __iomem *csr_diag; /* Diag CSR address of IP */ 94 void __iomem *csr_axi; /* AXI CSR address of IP */ 95 void __iomem *csr_mux; /* MUX CSR address of IP */ 96}; 97 98static int xgene_ahci_init_memram(struct xgene_ahci_context *ctx) 99{ 100 dev_dbg(ctx->dev, "Release memory from shutdown\n"); 101 writel(0x0, ctx->csr_diag + CFG_MEM_RAM_SHUTDOWN); 102 readl(ctx->csr_diag + CFG_MEM_RAM_SHUTDOWN); /* Force a barrier */ 103 msleep(1); /* reset may take up to 1ms */ 104 if (readl(ctx->csr_diag + BLOCK_MEM_RDY) != 0xFFFFFFFF) { 105 dev_err(ctx->dev, "failed to release memory from shutdown\n"); 106 return -ENODEV; 107 } 108 return 0; 109} 110 111/** 112 * xgene_ahci_poll_reg_val- Poll a register on a specific value. 113 * @ap : ATA port of interest. 114 * @reg : Register of interest. 115 * @val : Value to be attained. 116 * @interval : waiting interval for polling. 117 * @timeout : timeout for achieving the value. 118 */ 119static int xgene_ahci_poll_reg_val(struct ata_port *ap, 120 void __iomem *reg, unsigned 121 int val, unsigned long interval, 122 unsigned long timeout) 123{ 124 unsigned long deadline; 125 unsigned int tmp; 126 127 tmp = ioread32(reg); 128 deadline = ata_deadline(jiffies, timeout); 129 130 while (tmp != val && time_before(jiffies, deadline)) { 131 ata_msleep(ap, interval); 132 tmp = ioread32(reg); 133 } 134 135 return tmp; 136} 137 138/** 139 * xgene_ahci_restart_engine - Restart the dma engine. 140 * @ap : ATA port of interest 141 * 142 * Waits for completion of multiple commands and restarts 143 * the DMA engine inside the controller. 144 */ 145static int xgene_ahci_restart_engine(struct ata_port *ap) 146{ 147 struct ahci_host_priv *hpriv = ap->host->private_data; 148 struct ahci_port_priv *pp = ap->private_data; 149 void __iomem *port_mmio = ahci_port_base(ap); 150 u32 fbs; 151 152 /* 153 * In case of PMP multiple IDENTIFY DEVICE commands can be 154 * issued inside PxCI. So need to poll PxCI for the 155 * completion of outstanding IDENTIFY DEVICE commands before 156 * we restart the DMA engine. 157 */ 158 if (xgene_ahci_poll_reg_val(ap, port_mmio + 159 PORT_CMD_ISSUE, 0x0, 1, 100)) 160 return -EBUSY; 161 162 ahci_stop_engine(ap); 163 ahci_start_fis_rx(ap); 164 165 /* 166 * Enable the PxFBS.FBS_EN bit as it 167 * gets cleared due to stopping the engine. 168 */ 169 if (pp->fbs_supported) { 170 fbs = readl(port_mmio + PORT_FBS); 171 writel(fbs | PORT_FBS_EN, port_mmio + PORT_FBS); 172 fbs = readl(port_mmio + PORT_FBS); 173 } 174 175 hpriv->start_engine(ap); 176 177 return 0; 178} 179 180/** 181 * xgene_ahci_qc_issue - Issue commands to the device 182 * @qc: Command to issue 183 * 184 * Due to Hardware errata for IDENTIFY DEVICE command, the controller cannot 185 * clear the BSY bit after receiving the PIO setup FIS. This results in the dma 186 * state machine goes into the CMFatalErrorUpdate state and locks up. By 187 * restarting the dma engine, it removes the controller out of lock up state. 188 * 189 * Due to H/W errata, the controller is unable to save the PMP 190 * field fetched from command header before sending the H2D FIS. 191 * When the device returns the PMP port field in the D2H FIS, there is 192 * a mismatch and results in command completion failure. The 193 * workaround is to write the pmp value to PxFBS.DEV field before issuing 194 * any command to PMP. 195 */ 196static unsigned int xgene_ahci_qc_issue(struct ata_queued_cmd *qc) 197{ 198 struct ata_port *ap = qc->ap; 199 struct ahci_host_priv *hpriv = ap->host->private_data; 200 struct xgene_ahci_context *ctx = hpriv->plat_data; 201 int rc = 0; 202 u32 port_fbs; 203 void *port_mmio = ahci_port_base(ap); 204 205 /* 206 * Write the pmp value to PxFBS.DEV 207 * for case of Port Mulitplier. 208 */ 209 if (ctx->class[ap->port_no] == ATA_DEV_PMP) { 210 port_fbs = readl(port_mmio + PORT_FBS); 211 port_fbs &= ~PORT_FBS_DEV_MASK; 212 port_fbs |= qc->dev->link->pmp << PORT_FBS_DEV_OFFSET; 213 writel(port_fbs, port_mmio + PORT_FBS); 214 } 215 216 if (unlikely((ctx->last_cmd[ap->port_no] == ATA_CMD_ID_ATA) || 217 (ctx->last_cmd[ap->port_no] == ATA_CMD_PACKET) || 218 (ctx->last_cmd[ap->port_no] == ATA_CMD_SMART))) 219 xgene_ahci_restart_engine(ap); 220 221 rc = ahci_qc_issue(qc); 222 223 /* Save the last command issued */ 224 ctx->last_cmd[ap->port_no] = qc->tf.command; 225 226 return rc; 227} 228 229static bool xgene_ahci_is_memram_inited(struct xgene_ahci_context *ctx) 230{ 231 void __iomem *diagcsr = ctx->csr_diag; 232 233 return (readl(diagcsr + CFG_MEM_RAM_SHUTDOWN) == 0 && 234 readl(diagcsr + BLOCK_MEM_RDY) == 0xFFFFFFFF); 235} 236 237/** 238 * xgene_ahci_read_id - Read ID data from the specified device 239 * @dev: device 240 * @tf: proposed taskfile 241 * @id: data buffer 242 * 243 * This custom read ID function is required due to the fact that the HW 244 * does not support DEVSLP. 245 */ 246static unsigned int xgene_ahci_read_id(struct ata_device *dev, 247 struct ata_taskfile *tf, u16 *id) 248{ 249 u32 err_mask; 250 251 err_mask = ata_do_dev_read_id(dev, tf, id); 252 if (err_mask) 253 return err_mask; 254 255 /* 256 * Mask reserved area. Word78 spec of Link Power Management 257 * bit15-8: reserved 258 * bit7: NCQ autosence 259 * bit6: Software settings preservation supported 260 * bit5: reserved 261 * bit4: In-order sata delivery supported 262 * bit3: DIPM requests supported 263 * bit2: DMA Setup FIS Auto-Activate optimization supported 264 * bit1: DMA Setup FIX non-Zero buffer offsets supported 265 * bit0: Reserved 266 * 267 * Clear reserved bit 8 (DEVSLP bit) as we don't support DEVSLP 268 */ 269 id[ATA_ID_FEATURE_SUPP] &= cpu_to_le16(~(1 << 8)); 270 271 return 0; 272} 273 274static void xgene_ahci_set_phy_cfg(struct xgene_ahci_context *ctx, int channel) 275{ 276 void __iomem *mmio = ctx->hpriv->mmio; 277 u32 val; 278 279 dev_dbg(ctx->dev, "port configure mmio 0x%p channel %d\n", 280 mmio, channel); 281 val = readl(mmio + PORTCFG); 282 val = PORTADDR_SET(val, channel == 0 ? 2 : 3); 283 writel(val, mmio + PORTCFG); 284 readl(mmio + PORTCFG); /* Force a barrier */ 285 /* Disable fix rate */ 286 writel(0x0001fffe, mmio + PORTPHY1CFG); 287 readl(mmio + PORTPHY1CFG); /* Force a barrier */ 288 writel(0x28183219, mmio + PORTPHY2CFG); 289 readl(mmio + PORTPHY2CFG); /* Force a barrier */ 290 writel(0x13081008, mmio + PORTPHY3CFG); 291 readl(mmio + PORTPHY3CFG); /* Force a barrier */ 292 writel(0x00480815, mmio + PORTPHY4CFG); 293 readl(mmio + PORTPHY4CFG); /* Force a barrier */ 294 /* Set window negotiation */ 295 val = readl(mmio + PORTPHY5CFG); 296 val = PORTPHY5CFG_RTCHG_SET(val, 0x300); 297 writel(val, mmio + PORTPHY5CFG); 298 readl(mmio + PORTPHY5CFG); /* Force a barrier */ 299 val = readl(mmio + PORTAXICFG); 300 val = PORTAXICFG_EN_CONTEXT_SET(val, 0x1); /* Enable context mgmt */ 301 val = PORTAXICFG_OUTTRANS_SET(val, 0xe); /* Set outstanding */ 302 writel(val, mmio + PORTAXICFG); 303 readl(mmio + PORTAXICFG); /* Force a barrier */ 304 /* Set the watermark threshold of the receive FIFO */ 305 val = readl(mmio + PORTRANSCFG); 306 val = PORTRANSCFG_RXWM_SET(val, 0x30); 307 writel(val, mmio + PORTRANSCFG); 308} 309 310/** 311 * xgene_ahci_do_hardreset - Issue the actual COMRESET 312 * @link: link to reset 313 * @deadline: deadline jiffies for the operation 314 * @online: Return value to indicate if device online 315 * 316 * Due to the limitation of the hardware PHY, a difference set of setting is 317 * required for each supported disk speed - Gen3 (6.0Gbps), Gen2 (3.0Gbps), 318 * and Gen1 (1.5Gbps). Otherwise during long IO stress test, the PHY will 319 * report disparity error and etc. In addition, during COMRESET, there can 320 * be error reported in the register PORT_SCR_ERR. For SERR_DISPARITY and 321 * SERR_10B_8B_ERR, the PHY receiver line must be reseted. Also during long 322 * reboot cycle regression, sometimes the PHY reports link down even if the 323 * device is present because of speed negotiation failure. so need to retry 324 * the COMRESET to get the link up. The following algorithm is followed to 325 * proper configure the hardware PHY during COMRESET: 326 * 327 * Alg Part 1: 328 * 1. Start the PHY at Gen3 speed (default setting) 329 * 2. Issue the COMRESET 330 * 3. If no link, go to Alg Part 3 331 * 4. If link up, determine if the negotiated speed matches the PHY 332 * configured speed 333 * 5. If they matched, go to Alg Part 2 334 * 6. If they do not matched and first time, configure the PHY for the linked 335 * up disk speed and repeat step 2 336 * 7. Go to Alg Part 2 337 * 338 * Alg Part 2: 339 * 1. On link up, if there are any SERR_DISPARITY and SERR_10B_8B_ERR error 340 * reported in the register PORT_SCR_ERR, then reset the PHY receiver line 341 * 2. Go to Alg Part 4 342 * 343 * Alg Part 3: 344 * 1. Check the PORT_SCR_STAT to see whether device presence detected but PHY 345 * communication establishment failed and maximum link down attempts are 346 * less than Max attempts 3 then goto Alg Part 1. 347 * 2. Go to Alg Part 4. 348 * 349 * Alg Part 4: 350 * 1. Clear any pending from register PORT_SCR_ERR. 351 * 352 * NOTE: For the initial version, we will NOT support Gen1/Gen2. In addition 353 * and until the underlying PHY supports an method to reset the receiver 354 * line, on detection of SERR_DISPARITY or SERR_10B_8B_ERR errors, 355 * an warning message will be printed. 356 */ 357static int xgene_ahci_do_hardreset(struct ata_link *link, 358 unsigned long deadline, bool *online) 359{ 360 const unsigned long *timing = sata_ehc_deb_timing(&link->eh_context); 361 struct ata_port *ap = link->ap; 362 struct ahci_host_priv *hpriv = ap->host->private_data; 363 struct xgene_ahci_context *ctx = hpriv->plat_data; 364 struct ahci_port_priv *pp = ap->private_data; 365 u8 *d2h_fis = pp->rx_fis + RX_FIS_D2H_REG; 366 void __iomem *port_mmio = ahci_port_base(ap); 367 struct ata_taskfile tf; 368 int link_down_retry = 0; 369 int rc; 370 u32 val, sstatus; 371 372 do { 373 /* clear D2H reception area to properly wait for D2H FIS */ 374 ata_tf_init(link->device, &tf); 375 tf.command = ATA_BUSY; 376 ata_tf_to_fis(&tf, 0, 0, d2h_fis); 377 rc = sata_link_hardreset(link, timing, deadline, online, 378 ahci_check_ready); 379 if (*online) { 380 val = readl(port_mmio + PORT_SCR_ERR); 381 if (val & (SERR_DISPARITY | SERR_10B_8B_ERR)) 382 dev_warn(ctx->dev, "link has error\n"); 383 break; 384 } 385 386 sata_scr_read(link, SCR_STATUS, &sstatus); 387 } while (link_down_retry++ < MAX_LINK_DOWN_RETRY && 388 (sstatus & 0xff) == 0x1); 389 390 /* clear all errors if any pending */ 391 val = readl(port_mmio + PORT_SCR_ERR); 392 writel(val, port_mmio + PORT_SCR_ERR); 393 394 return rc; 395} 396 397static int xgene_ahci_hardreset(struct ata_link *link, unsigned int *class, 398 unsigned long deadline) 399{ 400 struct ata_port *ap = link->ap; 401 struct ahci_host_priv *hpriv = ap->host->private_data; 402 void __iomem *port_mmio = ahci_port_base(ap); 403 bool online; 404 int rc; 405 u32 portcmd_saved; 406 u32 portclb_saved; 407 u32 portclbhi_saved; 408 u32 portrxfis_saved; 409 u32 portrxfishi_saved; 410 411 /* As hardreset resets these CSR, save it to restore later */ 412 portcmd_saved = readl(port_mmio + PORT_CMD); 413 portclb_saved = readl(port_mmio + PORT_LST_ADDR); 414 portclbhi_saved = readl(port_mmio + PORT_LST_ADDR_HI); 415 portrxfis_saved = readl(port_mmio + PORT_FIS_ADDR); 416 portrxfishi_saved = readl(port_mmio + PORT_FIS_ADDR_HI); 417 418 ahci_stop_engine(ap); 419 420 rc = xgene_ahci_do_hardreset(link, deadline, &online); 421 422 /* As controller hardreset clears them, restore them */ 423 writel(portcmd_saved, port_mmio + PORT_CMD); 424 writel(portclb_saved, port_mmio + PORT_LST_ADDR); 425 writel(portclbhi_saved, port_mmio + PORT_LST_ADDR_HI); 426 writel(portrxfis_saved, port_mmio + PORT_FIS_ADDR); 427 writel(portrxfishi_saved, port_mmio + PORT_FIS_ADDR_HI); 428 429 hpriv->start_engine(ap); 430 431 if (online) 432 *class = ahci_dev_classify(ap); 433 434 return rc; 435} 436 437static void xgene_ahci_host_stop(struct ata_host *host) 438{ 439 struct ahci_host_priv *hpriv = host->private_data; 440 441 ahci_platform_disable_resources(hpriv); 442} 443 444/** 445 * xgene_ahci_pmp_softreset - Issue the softreset to the drives connected 446 * to Port Multiplier. 447 * @link: link to reset 448 * @class: Return value to indicate class of device 449 * @deadline: deadline jiffies for the operation 450 * 451 * Due to H/W errata, the controller is unable to save the PMP 452 * field fetched from command header before sending the H2D FIS. 453 * When the device returns the PMP port field in the D2H FIS, there is 454 * a mismatch and results in command completion failure. The workaround 455 * is to write the pmp value to PxFBS.DEV field before issuing any command 456 * to PMP. 457 */ 458static int xgene_ahci_pmp_softreset(struct ata_link *link, unsigned int *class, 459 unsigned long deadline) 460{ 461 int pmp = sata_srst_pmp(link); 462 struct ata_port *ap = link->ap; 463 u32 rc; 464 void *port_mmio = ahci_port_base(ap); 465 u32 port_fbs; 466 467 /* 468 * Set PxFBS.DEV field with pmp 469 * value. 470 */ 471 port_fbs = readl(port_mmio + PORT_FBS); 472 port_fbs &= ~PORT_FBS_DEV_MASK; 473 port_fbs |= pmp << PORT_FBS_DEV_OFFSET; 474 writel(port_fbs, port_mmio + PORT_FBS); 475 476 rc = ahci_do_softreset(link, class, pmp, deadline, ahci_check_ready); 477 478 return rc; 479} 480 481/** 482 * xgene_ahci_softreset - Issue the softreset to the drive. 483 * @link: link to reset 484 * @class: Return value to indicate class of device 485 * @deadline: deadline jiffies for the operation 486 * 487 * Due to H/W errata, the controller is unable to save the PMP 488 * field fetched from command header before sending the H2D FIS. 489 * When the device returns the PMP port field in the D2H FIS, there is 490 * a mismatch and results in command completion failure. The workaround 491 * is to write the pmp value to PxFBS.DEV field before issuing any command 492 * to PMP. Here is the algorithm to detect PMP : 493 * 494 * 1. Save the PxFBS value 495 * 2. Program PxFBS.DEV with pmp value send by framework. Framework sends 496 * 0xF for both PMP/NON-PMP initially 497 * 3. Issue softreset 498 * 4. If signature class is PMP goto 6 499 * 5. restore the original PxFBS and goto 3 500 * 6. return 501 */ 502static int xgene_ahci_softreset(struct ata_link *link, unsigned int *class, 503 unsigned long deadline) 504{ 505 int pmp = sata_srst_pmp(link); 506 struct ata_port *ap = link->ap; 507 struct ahci_host_priv *hpriv = ap->host->private_data; 508 struct xgene_ahci_context *ctx = hpriv->plat_data; 509 void *port_mmio = ahci_port_base(ap); 510 u32 port_fbs; 511 u32 port_fbs_save; 512 u32 retry = 1; 513 u32 rc; 514 515 port_fbs_save = readl(port_mmio + PORT_FBS); 516 517 /* 518 * Set PxFBS.DEV field with pmp 519 * value. 520 */ 521 port_fbs = readl(port_mmio + PORT_FBS); 522 port_fbs &= ~PORT_FBS_DEV_MASK; 523 port_fbs |= pmp << PORT_FBS_DEV_OFFSET; 524 writel(port_fbs, port_mmio + PORT_FBS); 525 526softreset_retry: 527 rc = ahci_do_softreset(link, class, pmp, 528 deadline, ahci_check_ready); 529 530 ctx->class[ap->port_no] = *class; 531 if (*class != ATA_DEV_PMP) { 532 /* 533 * Retry for normal drives without 534 * setting PxFBS.DEV field with pmp value. 535 */ 536 if (retry--) { 537 writel(port_fbs_save, port_mmio + PORT_FBS); 538 goto softreset_retry; 539 } 540 } 541 542 return rc; 543} 544 545static struct ata_port_operations xgene_ahci_ops = { 546 .inherits = &ahci_ops, 547 .host_stop = xgene_ahci_host_stop, 548 .hardreset = xgene_ahci_hardreset, 549 .read_id = xgene_ahci_read_id, 550 .qc_issue = xgene_ahci_qc_issue, 551 .softreset = xgene_ahci_softreset, 552 .pmp_softreset = xgene_ahci_pmp_softreset 553}; 554 555static const struct ata_port_info xgene_ahci_port_info = { 556 .flags = AHCI_FLAG_COMMON | ATA_FLAG_PMP, 557 .pio_mask = ATA_PIO4, 558 .udma_mask = ATA_UDMA6, 559 .port_ops = &xgene_ahci_ops, 560}; 561 562static int xgene_ahci_hw_init(struct ahci_host_priv *hpriv) 563{ 564 struct xgene_ahci_context *ctx = hpriv->plat_data; 565 int i; 566 int rc; 567 u32 val; 568 569 /* Remove IP RAM out of shutdown */ 570 rc = xgene_ahci_init_memram(ctx); 571 if (rc) 572 return rc; 573 574 for (i = 0; i < MAX_AHCI_CHN_PERCTR; i++) 575 xgene_ahci_set_phy_cfg(ctx, i); 576 577 /* AXI disable Mask */ 578 writel(0xffffffff, hpriv->mmio + HOST_IRQ_STAT); 579 readl(hpriv->mmio + HOST_IRQ_STAT); /* Force a barrier */ 580 writel(0, ctx->csr_core + INTSTATUSMASK); 581 val = readl(ctx->csr_core + INTSTATUSMASK); /* Force a barrier */ 582 dev_dbg(ctx->dev, "top level interrupt mask 0x%X value 0x%08X\n", 583 INTSTATUSMASK, val); 584 585 writel(0x0, ctx->csr_core + ERRINTSTATUSMASK); 586 readl(ctx->csr_core + ERRINTSTATUSMASK); /* Force a barrier */ 587 writel(0x0, ctx->csr_axi + INT_SLV_TMOMASK); 588 readl(ctx->csr_axi + INT_SLV_TMOMASK); 589 590 /* Enable AXI Interrupt */ 591 writel(0xffffffff, ctx->csr_core + SLVRDERRATTRIBUTES); 592 writel(0xffffffff, ctx->csr_core + SLVWRERRATTRIBUTES); 593 writel(0xffffffff, ctx->csr_core + MSTRDERRATTRIBUTES); 594 writel(0xffffffff, ctx->csr_core + MSTWRERRATTRIBUTES); 595 596 /* Enable coherency */ 597 val = readl(ctx->csr_core + BUSCTLREG); 598 val &= ~0x00000002; /* Enable write coherency */ 599 val &= ~0x00000001; /* Enable read coherency */ 600 writel(val, ctx->csr_core + BUSCTLREG); 601 602 val = readl(ctx->csr_core + IOFMSTRWAUX); 603 val |= (1 << 3); /* Enable read coherency */ 604 val |= (1 << 9); /* Enable write coherency */ 605 writel(val, ctx->csr_core + IOFMSTRWAUX); 606 val = readl(ctx->csr_core + IOFMSTRWAUX); 607 dev_dbg(ctx->dev, "coherency 0x%X value 0x%08X\n", 608 IOFMSTRWAUX, val); 609 610 return rc; 611} 612 613static int xgene_ahci_mux_select(struct xgene_ahci_context *ctx) 614{ 615 u32 val; 616 617 /* Check for optional MUX resource */ 618 if (!ctx->csr_mux) 619 return 0; 620 621 val = readl(ctx->csr_mux + SATA_ENET_CONFIG_REG); 622 val &= ~CFG_SATA_ENET_SELECT_MASK; 623 writel(val, ctx->csr_mux + SATA_ENET_CONFIG_REG); 624 val = readl(ctx->csr_mux + SATA_ENET_CONFIG_REG); 625 return val & CFG_SATA_ENET_SELECT_MASK ? -1 : 0; 626} 627 628static struct scsi_host_template ahci_platform_sht = { 629 AHCI_SHT(DRV_NAME), 630}; 631 632static int xgene_ahci_probe(struct platform_device *pdev) 633{ 634 struct device *dev = &pdev->dev; 635 struct ahci_host_priv *hpriv; 636 struct xgene_ahci_context *ctx; 637 struct resource *res; 638 int rc; 639 640 hpriv = ahci_platform_get_resources(pdev); 641 if (IS_ERR(hpriv)) 642 return PTR_ERR(hpriv); 643 644 ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); 645 if (!ctx) 646 return -ENOMEM; 647 648 hpriv->plat_data = ctx; 649 ctx->hpriv = hpriv; 650 ctx->dev = dev; 651 652 /* Retrieve the IP core resource */ 653 res = platform_get_resource(pdev, IORESOURCE_MEM, 1); 654 ctx->csr_core = devm_ioremap_resource(dev, res); 655 if (IS_ERR(ctx->csr_core)) 656 return PTR_ERR(ctx->csr_core); 657 658 /* Retrieve the IP diagnostic resource */ 659 res = platform_get_resource(pdev, IORESOURCE_MEM, 2); 660 ctx->csr_diag = devm_ioremap_resource(dev, res); 661 if (IS_ERR(ctx->csr_diag)) 662 return PTR_ERR(ctx->csr_diag); 663 664 /* Retrieve the IP AXI resource */ 665 res = platform_get_resource(pdev, IORESOURCE_MEM, 3); 666 ctx->csr_axi = devm_ioremap_resource(dev, res); 667 if (IS_ERR(ctx->csr_axi)) 668 return PTR_ERR(ctx->csr_axi); 669 670 /* Retrieve the optional IP mux resource */ 671 res = platform_get_resource(pdev, IORESOURCE_MEM, 4); 672 if (res) { 673 void __iomem *csr = devm_ioremap_resource(dev, res); 674 if (IS_ERR(csr)) 675 return PTR_ERR(csr); 676 677 ctx->csr_mux = csr; 678 } 679 680 dev_dbg(dev, "VAddr 0x%p Mmio VAddr 0x%p\n", ctx->csr_core, 681 hpriv->mmio); 682 683 /* Select ATA */ 684 if ((rc = xgene_ahci_mux_select(ctx))) { 685 dev_err(dev, "SATA mux selection failed error %d\n", rc); 686 return -ENODEV; 687 } 688 689 if (xgene_ahci_is_memram_inited(ctx)) { 690 dev_info(dev, "skip clock and PHY initialization\n"); 691 goto skip_clk_phy; 692 } 693 694 /* Due to errata, HW requires full toggle transition */ 695 rc = ahci_platform_enable_clks(hpriv); 696 if (rc) 697 goto disable_resources; 698 ahci_platform_disable_clks(hpriv); 699 700 rc = ahci_platform_enable_resources(hpriv); 701 if (rc) 702 goto disable_resources; 703 704 /* Configure the host controller */ 705 xgene_ahci_hw_init(hpriv); 706skip_clk_phy: 707 hpriv->flags = AHCI_HFLAG_NO_PMP | AHCI_HFLAG_NO_NCQ; 708 709 rc = ahci_platform_init_host(pdev, hpriv, &xgene_ahci_port_info, 710 &ahci_platform_sht); 711 if (rc) 712 goto disable_resources; 713 714 dev_dbg(dev, "X-Gene SATA host controller initialized\n"); 715 return 0; 716 717disable_resources: 718 ahci_platform_disable_resources(hpriv); 719 return rc; 720} 721 722#ifdef CONFIG_ACPI 723static const struct acpi_device_id xgene_ahci_acpi_match[] = { 724 { "APMC0D0D", }, 725 { } 726}; 727MODULE_DEVICE_TABLE(acpi, xgene_ahci_acpi_match); 728#endif 729 730static const struct of_device_id xgene_ahci_of_match[] = { 731 {.compatible = "apm,xgene-ahci"}, 732 {}, 733}; 734MODULE_DEVICE_TABLE(of, xgene_ahci_of_match); 735 736static struct platform_driver xgene_ahci_driver = { 737 .probe = xgene_ahci_probe, 738 .remove = ata_platform_remove_one, 739 .driver = { 740 .name = DRV_NAME, 741 .of_match_table = xgene_ahci_of_match, 742 .acpi_match_table = ACPI_PTR(xgene_ahci_acpi_match), 743 }, 744}; 745 746module_platform_driver(xgene_ahci_driver); 747 748MODULE_DESCRIPTION("APM X-Gene AHCI SATA driver"); 749MODULE_AUTHOR("Loc Ho <lho@apm.com>"); 750MODULE_LICENSE("GPL"); 751MODULE_VERSION("0.4"); 752