1/* mac89x0.c: A Crystal Semiconductor CS89[02]0 driver for linux. */ 2/* 3 Written 1996 by Russell Nelson, with reference to skeleton.c 4 written 1993-1994 by Donald Becker. 5 6 This software may be used and distributed according to the terms 7 of the GNU General Public License, incorporated herein by reference. 8 9 The author may be reached at nelson@crynwr.com, Crynwr 10 Software, 11 Grant St., Potsdam, NY 13676 11 12 Changelog: 13 14 Mike Cruse : mcruse@cti-ltd.com 15 : Changes for Linux 2.0 compatibility. 16 : Added dev_id parameter in net_interrupt(), 17 : request_irq() and free_irq(). Just NULL for now. 18 19 Mike Cruse : Added MOD_INC_USE_COUNT and MOD_DEC_USE_COUNT macros 20 : in net_open() and net_close() so kerneld would know 21 : that the module is in use and wouldn't eject the 22 : driver prematurely. 23 24 Mike Cruse : Rewrote init_module() and cleanup_module using 8390.c 25 : as an example. Disabled autoprobing in init_module(), 26 : not a good thing to do to other devices while Linux 27 : is running from all accounts. 28 29 Alan Cox : Removed 1.2 support, added 2.1 extra counters. 30 31 David Huggins-Daines <dhd@debian.org> 32 33 Split this off into mac89x0.c, and gutted it of all parts which are 34 not relevant to the existing CS8900 cards on the Macintosh 35 (i.e. basically the Daynaport CS and LC cards). To be precise: 36 37 * Removed all the media-detection stuff, because these cards are 38 TP-only. 39 40 * Lobotomized the ISA interrupt bogosity, because these cards use 41 a hardwired NuBus interrupt and a magic ISAIRQ value in the card. 42 43 * Basically eliminated everything not relevant to getting the 44 cards minimally functioning on the Macintosh. 45 46 I might add that these cards are badly designed even from the Mac 47 standpoint, in that Dayna, in their infinite wisdom, used NuBus slot 48 I/O space and NuBus interrupts for these cards, but neglected to 49 provide anything even remotely resembling a NuBus ROM. Therefore we 50 have to probe for them in a brain-damaged ISA-like fashion. 51 52 Arnaldo Carvalho de Melo <acme@conectiva.com.br> - 11/01/2001 53 check kmalloc and release the allocated memory on failure in 54 mac89x0_probe and in init_module 55 use local_irq_{save,restore}(flags) in net_get_stat, not just 56 local_irq_{dis,en}able() 57*/ 58 59static char *version = 60"cs89x0.c:v1.02 11/26/96 Russell Nelson <nelson@crynwr.com>\n"; 61 62/* ======================= configure the driver here ======================= */ 63 64/* use 0 for production, 1 for verification, >2 for debug */ 65#ifndef NET_DEBUG 66#define NET_DEBUG 0 67#endif 68 69/* ======================= end of configuration ======================= */ 70 71 72/* Always include 'config.h' first in case the user wants to turn on 73 or override something. */ 74#include <linux/module.h> 75 76/* 77 Sources: 78 79 Crynwr packet driver epktisa. 80 81 Crystal Semiconductor data sheets. 82 83*/ 84 85#include <linux/kernel.h> 86#include <linux/types.h> 87#include <linux/fcntl.h> 88#include <linux/interrupt.h> 89#include <linux/ioport.h> 90#include <linux/in.h> 91#include <linux/string.h> 92#include <linux/nubus.h> 93#include <linux/errno.h> 94#include <linux/init.h> 95#include <linux/netdevice.h> 96#include <linux/etherdevice.h> 97#include <linux/skbuff.h> 98#include <linux/delay.h> 99#include <linux/bitops.h> 100#include <linux/gfp.h> 101 102#include <asm/io.h> 103#include <asm/hwtest.h> 104#include <asm/macints.h> 105 106#include "cs89x0.h" 107 108static unsigned int net_debug = NET_DEBUG; 109 110/* Information that need to be kept for each board. */ 111struct net_local { 112 int chip_type; /* one of: CS8900, CS8920, CS8920M */ 113 char chip_revision; /* revision letter of the chip ('A'...) */ 114 int send_cmd; /* the propercommand used to send a packet. */ 115 int rx_mode; 116 int curr_rx_cfg; 117 int send_underrun; /* keep track of how many underruns in a row we get */ 118 struct sk_buff *skb; 119}; 120 121/* Index to functions, as function prototypes. */ 122 123#if 0 124extern void reset_chip(struct net_device *dev); 125#endif 126static int net_open(struct net_device *dev); 127static int net_send_packet(struct sk_buff *skb, struct net_device *dev); 128static irqreturn_t net_interrupt(int irq, void *dev_id); 129static void set_multicast_list(struct net_device *dev); 130static void net_rx(struct net_device *dev); 131static int net_close(struct net_device *dev); 132static struct net_device_stats *net_get_stats(struct net_device *dev); 133static int set_mac_address(struct net_device *dev, void *addr); 134 135 136/* Example routines you must write ;->. */ 137#define tx_done(dev) 1 138 139/* For reading/writing registers ISA-style */ 140static inline int 141readreg_io(struct net_device *dev, int portno) 142{ 143 nubus_writew(swab16(portno), dev->base_addr + ADD_PORT); 144 return swab16(nubus_readw(dev->base_addr + DATA_PORT)); 145} 146 147static inline void 148writereg_io(struct net_device *dev, int portno, int value) 149{ 150 nubus_writew(swab16(portno), dev->base_addr + ADD_PORT); 151 nubus_writew(swab16(value), dev->base_addr + DATA_PORT); 152} 153 154/* These are for reading/writing registers in shared memory */ 155static inline int 156readreg(struct net_device *dev, int portno) 157{ 158 return swab16(nubus_readw(dev->mem_start + portno)); 159} 160 161static inline void 162writereg(struct net_device *dev, int portno, int value) 163{ 164 nubus_writew(swab16(value), dev->mem_start + portno); 165} 166 167static const struct net_device_ops mac89x0_netdev_ops = { 168 .ndo_open = net_open, 169 .ndo_stop = net_close, 170 .ndo_start_xmit = net_send_packet, 171 .ndo_get_stats = net_get_stats, 172 .ndo_set_rx_mode = set_multicast_list, 173 .ndo_set_mac_address = set_mac_address, 174 .ndo_validate_addr = eth_validate_addr, 175 .ndo_change_mtu = eth_change_mtu, 176}; 177 178/* Probe for the CS8900 card in slot E. We won't bother looking 179 anywhere else until we have a really good reason to do so. */ 180struct net_device * __init mac89x0_probe(int unit) 181{ 182 struct net_device *dev; 183 static int once_is_enough; 184 struct net_local *lp; 185 static unsigned version_printed; 186 int i, slot; 187 unsigned rev_type = 0; 188 unsigned long ioaddr; 189 unsigned short sig; 190 int err = -ENODEV; 191 192 if (!MACH_IS_MAC) 193 return ERR_PTR(-ENODEV); 194 195 dev = alloc_etherdev(sizeof(struct net_local)); 196 if (!dev) 197 return ERR_PTR(-ENOMEM); 198 199 if (unit >= 0) { 200 sprintf(dev->name, "eth%d", unit); 201 netdev_boot_setup_check(dev); 202 } 203 204 if (once_is_enough) 205 goto out; 206 once_is_enough = 1; 207 208 /* We might have to parameterize this later */ 209 slot = 0xE; 210 /* Get out now if there's a real NuBus card in slot E */ 211 if (nubus_find_slot(slot, NULL) != NULL) 212 goto out; 213 214 /* The pseudo-ISA bits always live at offset 0x300 (gee, 215 wonder why...) */ 216 ioaddr = (unsigned long) 217 nubus_slot_addr(slot) | (((slot&0xf) << 20) + DEFAULTIOBASE); 218 { 219 int card_present; 220 221 card_present = (hwreg_present((void *)ioaddr + 4) && 222 hwreg_present((void *)ioaddr + DATA_PORT)); 223 if (!card_present) 224 goto out; 225 } 226 227 nubus_writew(0, ioaddr + ADD_PORT); 228 sig = nubus_readw(ioaddr + DATA_PORT); 229 if (sig != swab16(CHIP_EISA_ID_SIG)) 230 goto out; 231 232 /* Initialize the net_device structure. */ 233 lp = netdev_priv(dev); 234 235 /* Fill in the 'dev' fields. */ 236 dev->base_addr = ioaddr; 237 dev->mem_start = (unsigned long) 238 nubus_slot_addr(slot) | (((slot&0xf) << 20) + MMIOBASE); 239 dev->mem_end = dev->mem_start + 0x1000; 240 241 /* Turn on shared memory */ 242 writereg_io(dev, PP_BusCTL, MEMORY_ON); 243 244 /* get the chip type */ 245 rev_type = readreg(dev, PRODUCT_ID_ADD); 246 lp->chip_type = rev_type &~ REVISON_BITS; 247 lp->chip_revision = ((rev_type & REVISON_BITS) >> 8) + 'A'; 248 249 /* Check the chip type and revision in order to set the correct send command 250 CS8920 revision C and CS8900 revision F can use the faster send. */ 251 lp->send_cmd = TX_AFTER_381; 252 if (lp->chip_type == CS8900 && lp->chip_revision >= 'F') 253 lp->send_cmd = TX_NOW; 254 if (lp->chip_type != CS8900 && lp->chip_revision >= 'C') 255 lp->send_cmd = TX_NOW; 256 257 if (net_debug && version_printed++ == 0) 258 printk(version); 259 260 printk(KERN_INFO "%s: cs89%c0%s rev %c found at %#8lx", 261 dev->name, 262 lp->chip_type==CS8900?'0':'2', 263 lp->chip_type==CS8920M?"M":"", 264 lp->chip_revision, 265 dev->base_addr); 266 267 /* Try to read the MAC address */ 268 if ((readreg(dev, PP_SelfST) & (EEPROM_PRESENT | EEPROM_OK)) == 0) { 269 printk("\nmac89x0: No EEPROM, giving up now.\n"); 270 goto out1; 271 } else { 272 for (i = 0; i < ETH_ALEN; i += 2) { 273 /* Big-endian (why??!) */ 274 unsigned short s = readreg(dev, PP_IA + i); 275 dev->dev_addr[i] = s >> 8; 276 dev->dev_addr[i+1] = s & 0xff; 277 } 278 } 279 280 dev->irq = SLOT2IRQ(slot); 281 282 /* print the IRQ and ethernet address. */ 283 284 printk(" IRQ %d ADDR %pM\n", dev->irq, dev->dev_addr); 285 286 dev->netdev_ops = &mac89x0_netdev_ops; 287 288 err = register_netdev(dev); 289 if (err) 290 goto out1; 291 return NULL; 292out1: 293 nubus_writew(0, dev->base_addr + ADD_PORT); 294out: 295 free_netdev(dev); 296 return ERR_PTR(err); 297} 298 299#if 0 300/* This is useful for something, but I don't know what yet. */ 301void __init reset_chip(struct net_device *dev) 302{ 303 int reset_start_time; 304 305 writereg(dev, PP_SelfCTL, readreg(dev, PP_SelfCTL) | POWER_ON_RESET); 306 307 /* wait 30 ms */ 308 msleep_interruptible(30); 309 310 /* Wait until the chip is reset */ 311 reset_start_time = jiffies; 312 while( (readreg(dev, PP_SelfST) & INIT_DONE) == 0 && jiffies - reset_start_time < 2) 313 ; 314} 315#endif 316 317/* Open/initialize the board. This is called (in the current kernel) 318 sometime after booting when the 'ifconfig' program is run. 319 320 This routine should set everything up anew at each open, even 321 registers that "should" only need to be set once at boot, so that 322 there is non-reboot way to recover if something goes wrong. 323 */ 324static int 325net_open(struct net_device *dev) 326{ 327 struct net_local *lp = netdev_priv(dev); 328 int i; 329 330 /* Disable the interrupt for now */ 331 writereg(dev, PP_BusCTL, readreg(dev, PP_BusCTL) & ~ENABLE_IRQ); 332 333 /* Grab the interrupt */ 334 if (request_irq(dev->irq, net_interrupt, 0, "cs89x0", dev)) 335 return -EAGAIN; 336 337 /* Set up the IRQ - Apparently magic */ 338 if (lp->chip_type == CS8900) 339 writereg(dev, PP_CS8900_ISAINT, 0); 340 else 341 writereg(dev, PP_CS8920_ISAINT, 0); 342 343 /* set the Ethernet address */ 344 for (i=0; i < ETH_ALEN/2; i++) 345 writereg(dev, PP_IA+i*2, dev->dev_addr[i*2] | (dev->dev_addr[i*2+1] << 8)); 346 347 /* Turn on both receive and transmit operations */ 348 writereg(dev, PP_LineCTL, readreg(dev, PP_LineCTL) | SERIAL_RX_ON | SERIAL_TX_ON); 349 350 /* Receive only error free packets addressed to this card */ 351 lp->rx_mode = 0; 352 writereg(dev, PP_RxCTL, DEF_RX_ACCEPT); 353 354 lp->curr_rx_cfg = RX_OK_ENBL | RX_CRC_ERROR_ENBL; 355 356 writereg(dev, PP_RxCFG, lp->curr_rx_cfg); 357 358 writereg(dev, PP_TxCFG, TX_LOST_CRS_ENBL | TX_SQE_ERROR_ENBL | TX_OK_ENBL | 359 TX_LATE_COL_ENBL | TX_JBR_ENBL | TX_ANY_COL_ENBL | TX_16_COL_ENBL); 360 361 writereg(dev, PP_BufCFG, READY_FOR_TX_ENBL | RX_MISS_COUNT_OVRFLOW_ENBL | 362 TX_COL_COUNT_OVRFLOW_ENBL | TX_UNDERRUN_ENBL); 363 364 /* now that we've got our act together, enable everything */ 365 writereg(dev, PP_BusCTL, readreg(dev, PP_BusCTL) | ENABLE_IRQ); 366 netif_start_queue(dev); 367 return 0; 368} 369 370static int 371net_send_packet(struct sk_buff *skb, struct net_device *dev) 372{ 373 struct net_local *lp = netdev_priv(dev); 374 unsigned long flags; 375 376 if (net_debug > 3) 377 printk("%s: sent %d byte packet of type %x\n", 378 dev->name, skb->len, 379 (skb->data[ETH_ALEN+ETH_ALEN] << 8) 380 | skb->data[ETH_ALEN+ETH_ALEN+1]); 381 382 /* keep the upload from being interrupted, since we 383 ask the chip to start transmitting before the 384 whole packet has been completely uploaded. */ 385 local_irq_save(flags); 386 netif_stop_queue(dev); 387 388 /* initiate a transmit sequence */ 389 writereg(dev, PP_TxCMD, lp->send_cmd); 390 writereg(dev, PP_TxLength, skb->len); 391 392 /* Test to see if the chip has allocated memory for the packet */ 393 if ((readreg(dev, PP_BusST) & READY_FOR_TX_NOW) == 0) { 394 /* Gasp! It hasn't. But that shouldn't happen since 395 we're waiting for TxOk, so return 1 and requeue this packet. */ 396 local_irq_restore(flags); 397 return NETDEV_TX_BUSY; 398 } 399 400 /* Write the contents of the packet */ 401 skb_copy_from_linear_data(skb, (void *)(dev->mem_start + PP_TxFrame), 402 skb->len+1); 403 404 local_irq_restore(flags); 405 dev_kfree_skb (skb); 406 407 return NETDEV_TX_OK; 408} 409 410/* The typical workload of the driver: 411 Handle the network interface interrupts. */ 412static irqreturn_t net_interrupt(int irq, void *dev_id) 413{ 414 struct net_device *dev = dev_id; 415 struct net_local *lp; 416 int ioaddr, status; 417 418 if (dev == NULL) { 419 printk ("net_interrupt(): irq %d for unknown device.\n", irq); 420 return IRQ_NONE; 421 } 422 423 ioaddr = dev->base_addr; 424 lp = netdev_priv(dev); 425 426 /* we MUST read all the events out of the ISQ, otherwise we'll never 427 get interrupted again. As a consequence, we can't have any limit 428 on the number of times we loop in the interrupt handler. The 429 hardware guarantees that eventually we'll run out of events. Of 430 course, if you're on a slow machine, and packets are arriving 431 faster than you can read them off, you're screwed. Hasta la 432 vista, baby! */ 433 while ((status = swab16(nubus_readw(dev->base_addr + ISQ_PORT)))) { 434 if (net_debug > 4)printk("%s: event=%04x\n", dev->name, status); 435 switch(status & ISQ_EVENT_MASK) { 436 case ISQ_RECEIVER_EVENT: 437 /* Got a packet(s). */ 438 net_rx(dev); 439 break; 440 case ISQ_TRANSMITTER_EVENT: 441 dev->stats.tx_packets++; 442 netif_wake_queue(dev); 443 if ((status & TX_OK) == 0) 444 dev->stats.tx_errors++; 445 if (status & TX_LOST_CRS) 446 dev->stats.tx_carrier_errors++; 447 if (status & TX_SQE_ERROR) 448 dev->stats.tx_heartbeat_errors++; 449 if (status & TX_LATE_COL) 450 dev->stats.tx_window_errors++; 451 if (status & TX_16_COL) 452 dev->stats.tx_aborted_errors++; 453 break; 454 case ISQ_BUFFER_EVENT: 455 if (status & READY_FOR_TX) { 456 /* we tried to transmit a packet earlier, 457 but inexplicably ran out of buffers. 458 That shouldn't happen since we only ever 459 load one packet. Shrug. Do the right 460 thing anyway. */ 461 netif_wake_queue(dev); 462 } 463 if (status & TX_UNDERRUN) { 464 if (net_debug > 0) printk("%s: transmit underrun\n", dev->name); 465 lp->send_underrun++; 466 if (lp->send_underrun == 3) lp->send_cmd = TX_AFTER_381; 467 else if (lp->send_underrun == 6) lp->send_cmd = TX_AFTER_ALL; 468 } 469 break; 470 case ISQ_RX_MISS_EVENT: 471 dev->stats.rx_missed_errors += (status >> 6); 472 break; 473 case ISQ_TX_COL_EVENT: 474 dev->stats.collisions += (status >> 6); 475 break; 476 } 477 } 478 return IRQ_HANDLED; 479} 480 481/* We have a good packet(s), get it/them out of the buffers. */ 482static void 483net_rx(struct net_device *dev) 484{ 485 struct sk_buff *skb; 486 int status, length; 487 488 status = readreg(dev, PP_RxStatus); 489 if ((status & RX_OK) == 0) { 490 dev->stats.rx_errors++; 491 if (status & RX_RUNT) 492 dev->stats.rx_length_errors++; 493 if (status & RX_EXTRA_DATA) 494 dev->stats.rx_length_errors++; 495 if ((status & RX_CRC_ERROR) && 496 !(status & (RX_EXTRA_DATA|RX_RUNT))) 497 /* per str 172 */ 498 dev->stats.rx_crc_errors++; 499 if (status & RX_DRIBBLE) 500 dev->stats.rx_frame_errors++; 501 return; 502 } 503 504 length = readreg(dev, PP_RxLength); 505 /* Malloc up new buffer. */ 506 skb = alloc_skb(length, GFP_ATOMIC); 507 if (skb == NULL) { 508 printk("%s: Memory squeeze, dropping packet.\n", dev->name); 509 dev->stats.rx_dropped++; 510 return; 511 } 512 skb_put(skb, length); 513 514 skb_copy_to_linear_data(skb, (void *)(dev->mem_start + PP_RxFrame), 515 length); 516 517 if (net_debug > 3)printk("%s: received %d byte packet of type %x\n", 518 dev->name, length, 519 (skb->data[ETH_ALEN+ETH_ALEN] << 8) 520 | skb->data[ETH_ALEN+ETH_ALEN+1]); 521 522 skb->protocol=eth_type_trans(skb,dev); 523 netif_rx(skb); 524 dev->stats.rx_packets++; 525 dev->stats.rx_bytes += length; 526} 527 528/* The inverse routine to net_open(). */ 529static int 530net_close(struct net_device *dev) 531{ 532 533 writereg(dev, PP_RxCFG, 0); 534 writereg(dev, PP_TxCFG, 0); 535 writereg(dev, PP_BufCFG, 0); 536 writereg(dev, PP_BusCTL, 0); 537 538 netif_stop_queue(dev); 539 540 free_irq(dev->irq, dev); 541 542 /* Update the statistics here. */ 543 544 return 0; 545 546} 547 548/* Get the current statistics. This may be called with the card open or 549 closed. */ 550static struct net_device_stats * 551net_get_stats(struct net_device *dev) 552{ 553 unsigned long flags; 554 555 local_irq_save(flags); 556 /* Update the statistics from the device registers. */ 557 dev->stats.rx_missed_errors += (readreg(dev, PP_RxMiss) >> 6); 558 dev->stats.collisions += (readreg(dev, PP_TxCol) >> 6); 559 local_irq_restore(flags); 560 561 return &dev->stats; 562} 563 564static void set_multicast_list(struct net_device *dev) 565{ 566 struct net_local *lp = netdev_priv(dev); 567 568 if(dev->flags&IFF_PROMISC) 569 { 570 lp->rx_mode = RX_ALL_ACCEPT; 571 } else if ((dev->flags & IFF_ALLMULTI) || !netdev_mc_empty(dev)) { 572 /* The multicast-accept list is initialized to accept-all, and we 573 rely on higher-level filtering for now. */ 574 lp->rx_mode = RX_MULTCAST_ACCEPT; 575 } 576 else 577 lp->rx_mode = 0; 578 579 writereg(dev, PP_RxCTL, DEF_RX_ACCEPT | lp->rx_mode); 580 581 /* in promiscuous mode, we accept errored packets, so we have to enable interrupts on them also */ 582 writereg(dev, PP_RxCFG, lp->curr_rx_cfg | 583 (lp->rx_mode == RX_ALL_ACCEPT? (RX_CRC_ERROR_ENBL|RX_RUNT_ENBL|RX_EXTRA_DATA_ENBL) : 0)); 584} 585 586 587static int set_mac_address(struct net_device *dev, void *addr) 588{ 589 struct sockaddr *saddr = addr; 590 int i; 591 592 if (!is_valid_ether_addr(saddr->sa_data)) 593 return -EADDRNOTAVAIL; 594 595 memcpy(dev->dev_addr, saddr->sa_data, ETH_ALEN); 596 printk("%s: Setting MAC address to %pM\n", dev->name, dev->dev_addr); 597 598 /* set the Ethernet address */ 599 for (i=0; i < ETH_ALEN/2; i++) 600 writereg(dev, PP_IA+i*2, dev->dev_addr[i*2] | (dev->dev_addr[i*2+1] << 8)); 601 602 return 0; 603} 604 605#ifdef MODULE 606 607static struct net_device *dev_cs89x0; 608static int debug; 609 610module_param(debug, int, 0); 611MODULE_PARM_DESC(debug, "CS89[02]0 debug level (0-5)"); 612MODULE_LICENSE("GPL"); 613 614int __init 615init_module(void) 616{ 617 net_debug = debug; 618 dev_cs89x0 = mac89x0_probe(-1); 619 if (IS_ERR(dev_cs89x0)) { 620 printk(KERN_WARNING "mac89x0.c: No card found\n"); 621 return PTR_ERR(dev_cs89x0); 622 } 623 return 0; 624} 625 626void 627cleanup_module(void) 628{ 629 unregister_netdev(dev_cs89x0); 630 nubus_writew(0, dev_cs89x0->base_addr + ADD_PORT); 631 free_netdev(dev_cs89x0); 632} 633#endif /* MODULE */ 634