1#ifndef B43_H_ 2#define B43_H_ 3 4#include <linux/kernel.h> 5#include <linux/spinlock.h> 6#include <linux/interrupt.h> 7#include <linux/hw_random.h> 8#include <linux/bcma/bcma.h> 9#include <linux/ssb/ssb.h> 10#include <linux/completion.h> 11#include <net/mac80211.h> 12 13#include "debugfs.h" 14#include "leds.h" 15#include "rfkill.h" 16#include "bus.h" 17#include "lo.h" 18#include "phy_common.h" 19 20 21#ifdef CONFIG_B43_DEBUG 22# define B43_DEBUG 1 23#else 24# define B43_DEBUG 0 25#endif 26 27/* MMIO offsets */ 28#define B43_MMIO_DMA0_REASON 0x20 29#define B43_MMIO_DMA0_IRQ_MASK 0x24 30#define B43_MMIO_DMA1_REASON 0x28 31#define B43_MMIO_DMA1_IRQ_MASK 0x2C 32#define B43_MMIO_DMA2_REASON 0x30 33#define B43_MMIO_DMA2_IRQ_MASK 0x34 34#define B43_MMIO_DMA3_REASON 0x38 35#define B43_MMIO_DMA3_IRQ_MASK 0x3C 36#define B43_MMIO_DMA4_REASON 0x40 37#define B43_MMIO_DMA4_IRQ_MASK 0x44 38#define B43_MMIO_DMA5_REASON 0x48 39#define B43_MMIO_DMA5_IRQ_MASK 0x4C 40#define B43_MMIO_MACCTL 0x120 /* MAC control */ 41#define B43_MMIO_MACCMD 0x124 /* MAC command */ 42#define B43_MMIO_GEN_IRQ_REASON 0x128 43#define B43_MMIO_GEN_IRQ_MASK 0x12C 44#define B43_MMIO_RAM_CONTROL 0x130 45#define B43_MMIO_RAM_DATA 0x134 46#define B43_MMIO_PS_STATUS 0x140 47#define B43_MMIO_RADIO_HWENABLED_HI 0x158 48#define B43_MMIO_MAC_HW_CAP 0x15C /* MAC capabilities (corerev >= 13) */ 49#define B43_MMIO_SHM_CONTROL 0x160 50#define B43_MMIO_SHM_DATA 0x164 51#define B43_MMIO_SHM_DATA_UNALIGNED 0x166 52#define B43_MMIO_XMITSTAT_0 0x170 53#define B43_MMIO_XMITSTAT_1 0x174 54#define B43_MMIO_REV3PLUS_TSF_LOW 0x180 /* core rev >= 3 only */ 55#define B43_MMIO_REV3PLUS_TSF_HIGH 0x184 /* core rev >= 3 only */ 56#define B43_MMIO_TSF_CFP_REP 0x188 57#define B43_MMIO_TSF_CFP_START 0x18C 58#define B43_MMIO_TSF_CFP_MAXDUR 0x190 59 60/* 32-bit DMA */ 61#define B43_MMIO_DMA32_BASE0 0x200 62#define B43_MMIO_DMA32_BASE1 0x220 63#define B43_MMIO_DMA32_BASE2 0x240 64#define B43_MMIO_DMA32_BASE3 0x260 65#define B43_MMIO_DMA32_BASE4 0x280 66#define B43_MMIO_DMA32_BASE5 0x2A0 67/* 64-bit DMA */ 68#define B43_MMIO_DMA64_BASE0 0x200 69#define B43_MMIO_DMA64_BASE1 0x240 70#define B43_MMIO_DMA64_BASE2 0x280 71#define B43_MMIO_DMA64_BASE3 0x2C0 72#define B43_MMIO_DMA64_BASE4 0x300 73#define B43_MMIO_DMA64_BASE5 0x340 74 75/* PIO on core rev < 11 */ 76#define B43_MMIO_PIO_BASE0 0x300 77#define B43_MMIO_PIO_BASE1 0x310 78#define B43_MMIO_PIO_BASE2 0x320 79#define B43_MMIO_PIO_BASE3 0x330 80#define B43_MMIO_PIO_BASE4 0x340 81#define B43_MMIO_PIO_BASE5 0x350 82#define B43_MMIO_PIO_BASE6 0x360 83#define B43_MMIO_PIO_BASE7 0x370 84/* PIO on core rev >= 11 */ 85#define B43_MMIO_PIO11_BASE0 0x200 86#define B43_MMIO_PIO11_BASE1 0x240 87#define B43_MMIO_PIO11_BASE2 0x280 88#define B43_MMIO_PIO11_BASE3 0x2C0 89#define B43_MMIO_PIO11_BASE4 0x300 90#define B43_MMIO_PIO11_BASE5 0x340 91 92#define B43_MMIO_RADIO24_CONTROL 0x3D8 /* core rev >= 24 only */ 93#define B43_MMIO_RADIO24_DATA 0x3DA /* core rev >= 24 only */ 94#define B43_MMIO_PHY_VER 0x3E0 95#define B43_MMIO_PHY_RADIO 0x3E2 96#define B43_MMIO_PHY0 0x3E6 97#define B43_MMIO_ANTENNA 0x3E8 98#define B43_MMIO_CHANNEL 0x3F0 99#define B43_MMIO_CHANNEL_EXT 0x3F4 100#define B43_MMIO_RADIO_CONTROL 0x3F6 101#define B43_MMIO_RADIO_DATA_HIGH 0x3F8 102#define B43_MMIO_RADIO_DATA_LOW 0x3FA 103#define B43_MMIO_PHY_CONTROL 0x3FC 104#define B43_MMIO_PHY_DATA 0x3FE 105#define B43_MMIO_MACFILTER_CONTROL 0x420 106#define B43_MMIO_MACFILTER_DATA 0x422 107#define B43_MMIO_RCMTA_COUNT 0x43C 108#define B43_MMIO_PSM_PHY_HDR 0x492 109#define B43_MMIO_RADIO_HWENABLED_LO 0x49A 110#define B43_MMIO_GPIO_CONTROL 0x49C 111#define B43_MMIO_GPIO_MASK 0x49E 112#define B43_MMIO_TXE0_CTL 0x500 113#define B43_MMIO_TXE0_AUX 0x502 114#define B43_MMIO_TXE0_TS_LOC 0x504 115#define B43_MMIO_TXE0_TIME_OUT 0x506 116#define B43_MMIO_TXE0_WM_0 0x508 117#define B43_MMIO_TXE0_WM_1 0x50A 118#define B43_MMIO_TXE0_PHYCTL 0x50C 119#define B43_MMIO_TXE0_STATUS 0x50E 120#define B43_MMIO_TXE0_MMPLCP0 0x510 121#define B43_MMIO_TXE0_MMPLCP1 0x512 122#define B43_MMIO_TXE0_PHYCTL1 0x514 123#define B43_MMIO_XMTFIFODEF 0x520 124#define B43_MMIO_XMTFIFO_FRAME_CNT 0x522 /* core rev>= 16 only */ 125#define B43_MMIO_XMTFIFO_BYTE_CNT 0x524 /* core rev>= 16 only */ 126#define B43_MMIO_XMTFIFO_HEAD 0x526 /* core rev>= 16 only */ 127#define B43_MMIO_XMTFIFO_RD_PTR 0x528 /* core rev>= 16 only */ 128#define B43_MMIO_XMTFIFO_WR_PTR 0x52A /* core rev>= 16 only */ 129#define B43_MMIO_XMTFIFODEF1 0x52C /* core rev>= 16 only */ 130#define B43_MMIO_XMTFIFOCMD 0x540 131#define B43_MMIO_XMTFIFOFLUSH 0x542 132#define B43_MMIO_XMTFIFOTHRESH 0x544 133#define B43_MMIO_XMTFIFORDY 0x546 134#define B43_MMIO_XMTFIFOPRIRDY 0x548 135#define B43_MMIO_XMTFIFORQPRI 0x54A 136#define B43_MMIO_XMTTPLATETXPTR 0x54C 137#define B43_MMIO_XMTTPLATEPTR 0x550 138#define B43_MMIO_SMPL_CLCT_STRPTR 0x552 /* core rev>= 22 only */ 139#define B43_MMIO_SMPL_CLCT_STPPTR 0x554 /* core rev>= 22 only */ 140#define B43_MMIO_SMPL_CLCT_CURPTR 0x556 /* core rev>= 22 only */ 141#define B43_MMIO_XMTTPLATEDATALO 0x560 142#define B43_MMIO_XMTTPLATEDATAHI 0x562 143#define B43_MMIO_XMTSEL 0x568 144#define B43_MMIO_XMTTXCNT 0x56A 145#define B43_MMIO_XMTTXSHMADDR 0x56C 146#define B43_MMIO_TSF_CFP_START_LOW 0x604 147#define B43_MMIO_TSF_CFP_START_HIGH 0x606 148#define B43_MMIO_TSF_CFP_PRETBTT 0x612 149#define B43_MMIO_TSF_CLK_FRAC_LOW 0x62E 150#define B43_MMIO_TSF_CLK_FRAC_HIGH 0x630 151#define B43_MMIO_TSF_0 0x632 /* core rev < 3 only */ 152#define B43_MMIO_TSF_1 0x634 /* core rev < 3 only */ 153#define B43_MMIO_TSF_2 0x636 /* core rev < 3 only */ 154#define B43_MMIO_TSF_3 0x638 /* core rev < 3 only */ 155#define B43_MMIO_RNG 0x65A 156#define B43_MMIO_IFSSLOT 0x684 /* Interframe slot time */ 157#define B43_MMIO_IFSCTL 0x688 /* Interframe space control */ 158#define B43_MMIO_IFSSTAT 0x690 159#define B43_MMIO_IFSMEDBUSYCTL 0x692 160#define B43_MMIO_IFTXDUR 0x694 161#define B43_MMIO_IFSCTL_USE_EDCF 0x0004 162#define B43_MMIO_POWERUP_DELAY 0x6A8 163#define B43_MMIO_BTCOEX_CTL 0x6B4 /* Bluetooth Coexistence Control */ 164#define B43_MMIO_BTCOEX_STAT 0x6B6 /* Bluetooth Coexistence Status */ 165#define B43_MMIO_BTCOEX_TXCTL 0x6B8 /* Bluetooth Coexistence Transmit Control */ 166#define B43_MMIO_WEPCTL 0x7C0 167 168/* SPROM boardflags_lo values */ 169#define B43_BFL_BTCOEXIST 0x0001 /* implements Bluetooth coexistance */ 170#define B43_BFL_PACTRL 0x0002 /* GPIO 9 controlling the PA */ 171#define B43_BFL_AIRLINEMODE 0x0004 /* implements GPIO 13 radio disable indication */ 172#define B43_BFL_RSSI 0x0008 /* software calculates nrssi slope. */ 173#define B43_BFL_ENETSPI 0x0010 /* has ephy roboswitch spi */ 174#define B43_BFL_XTAL_NOSLOW 0x0020 /* no slow clock available */ 175#define B43_BFL_CCKHIPWR 0x0040 /* can do high power CCK transmission */ 176#define B43_BFL_ENETADM 0x0080 /* has ADMtek switch */ 177#define B43_BFL_ENETVLAN 0x0100 /* can do vlan */ 178#define B43_BFL_AFTERBURNER 0x0200 /* supports Afterburner mode */ 179#define B43_BFL_NOPCI 0x0400 /* leaves PCI floating */ 180#define B43_BFL_FEM 0x0800 /* supports the Front End Module */ 181#define B43_BFL_EXTLNA 0x1000 /* has an external LNA */ 182#define B43_BFL_HGPA 0x2000 /* had high gain PA */ 183#define B43_BFL_BTCMOD 0x4000 /* BFL_BTCOEXIST is given in alternate GPIOs */ 184#define B43_BFL_ALTIQ 0x8000 /* alternate I/Q settings */ 185 186/* SPROM boardflags_hi values */ 187#define B43_BFH_NOPA 0x0001 /* has no PA */ 188#define B43_BFH_RSSIINV 0x0002 /* RSSI uses positive slope (not TSSI) */ 189#define B43_BFH_PAREF 0x0004 /* uses the PARef LDO */ 190#define B43_BFH_3TSWITCH 0x0008 /* uses a triple throw switch shared 191 * with bluetooth */ 192#define B43_BFH_PHASESHIFT 0x0010 /* can support phase shifter */ 193#define B43_BFH_BUCKBOOST 0x0020 /* has buck/booster */ 194#define B43_BFH_FEM_BT 0x0040 /* has FEM and switch to share antenna 195 * with bluetooth */ 196#define B43_BFH_NOCBUCK 0x0080 197#define B43_BFH_PALDO 0x0200 198#define B43_BFH_EXTLNA_5GHZ 0x1000 /* has an external LNA (5GHz mode) */ 199 200/* SPROM boardflags2_lo values */ 201#define B43_BFL2_RXBB_INT_REG_DIS 0x0001 /* external RX BB regulator present */ 202#define B43_BFL2_APLL_WAR 0x0002 /* alternative A-band PLL settings implemented */ 203#define B43_BFL2_TXPWRCTRL_EN 0x0004 /* permits enabling TX Power Control */ 204#define B43_BFL2_2X4_DIV 0x0008 /* 2x4 diversity switch */ 205#define B43_BFL2_5G_PWRGAIN 0x0010 /* supports 5G band power gain */ 206#define B43_BFL2_PCIEWAR_OVR 0x0020 /* overrides ASPM and Clkreq settings */ 207#define B43_BFL2_CAESERS_BRD 0x0040 /* is Caesers board (unused) */ 208#define B43_BFL2_BTC3WIRE 0x0080 /* used 3-wire bluetooth coexist */ 209#define B43_BFL2_SKWRKFEM_BRD 0x0100 /* 4321mcm93 uses Skyworks FEM */ 210#define B43_BFL2_SPUR_WAR 0x0200 /* has a workaround for clock-harmonic spurs */ 211#define B43_BFL2_GPLL_WAR 0x0400 /* altenative G-band PLL settings implemented */ 212#define B43_BFL2_SINGLEANT_CCK 0x1000 213#define B43_BFL2_2G_SPUR_WAR 0x2000 214 215/* SPROM boardflags2_hi values */ 216#define B43_BFH2_GPLL_WAR2 0x0001 217#define B43_BFH2_IPALVLSHIFT_3P3 0x0002 218#define B43_BFH2_INTERNDET_TXIQCAL 0x0004 219#define B43_BFH2_XTALBUFOUTEN 0x0008 220 221/* GPIO register offset, in both ChipCommon and PCI core. */ 222#define B43_GPIO_CONTROL 0x6c 223 224/* SHM Routing */ 225enum { 226 B43_SHM_UCODE, /* Microcode memory */ 227 B43_SHM_SHARED, /* Shared memory */ 228 B43_SHM_SCRATCH, /* Scratch memory */ 229 B43_SHM_HW, /* Internal hardware register */ 230 B43_SHM_RCMTA, /* Receive match transmitter address (rev >= 5 only) */ 231}; 232/* SHM Routing modifiers */ 233#define B43_SHM_AUTOINC_R 0x0200 /* Auto-increment address on read */ 234#define B43_SHM_AUTOINC_W 0x0100 /* Auto-increment address on write */ 235#define B43_SHM_AUTOINC_RW (B43_SHM_AUTOINC_R | \ 236 B43_SHM_AUTOINC_W) 237 238/* Misc SHM_SHARED offsets */ 239#define B43_SHM_SH_WLCOREREV 0x0016 /* 802.11 core revision */ 240#define B43_SHM_SH_PCTLWDPOS 0x0008 241#define B43_SHM_SH_RXPADOFF 0x0034 /* RX Padding data offset (PIO only) */ 242#define B43_SHM_SH_FWCAPA 0x0042 /* Firmware capabilities (Opensource firmware only) */ 243#define B43_SHM_SH_PHYVER 0x0050 /* PHY version */ 244#define B43_SHM_SH_PHYTYPE 0x0052 /* PHY type */ 245#define B43_SHM_SH_ANTSWAP 0x005C /* Antenna swap threshold */ 246#define B43_SHM_SH_HOSTF1 0x005E /* Hostflags 1 for ucode options */ 247#define B43_SHM_SH_HOSTF2 0x0060 /* Hostflags 2 for ucode options */ 248#define B43_SHM_SH_HOSTF3 0x0062 /* Hostflags 3 for ucode options */ 249#define B43_SHM_SH_RFATT 0x0064 /* Current radio attenuation value */ 250#define B43_SHM_SH_RADAR 0x0066 /* Radar register */ 251#define B43_SHM_SH_PHYTXNOI 0x006E /* PHY noise directly after TX (lower 8bit only) */ 252#define B43_SHM_SH_RFRXSP1 0x0072 /* RF RX SP Register 1 */ 253#define B43_SHM_SH_HOSTF4 0x0078 /* Hostflags 4 for ucode options */ 254#define B43_SHM_SH_CHAN 0x00A0 /* Current channel (low 8bit only) */ 255#define B43_SHM_SH_CHAN_5GHZ 0x0100 /* Bit set, if 5 Ghz channel */ 256#define B43_SHM_SH_CHAN_40MHZ 0x0200 /* Bit set, if 40 Mhz channel width */ 257#define B43_SHM_SH_MACHW_L 0x00C0 /* Location where the ucode expects the MAC capabilities */ 258#define B43_SHM_SH_MACHW_H 0x00C2 /* Location where the ucode expects the MAC capabilities */ 259#define B43_SHM_SH_HOSTF5 0x00D4 /* Hostflags 5 for ucode options */ 260#define B43_SHM_SH_BCMCFIFOID 0x0108 /* Last posted cookie to the bcast/mcast FIFO */ 261/* TSSI information */ 262#define B43_SHM_SH_TSSI_CCK 0x0058 /* TSSI for last 4 CCK frames (32bit) */ 263#define B43_SHM_SH_TSSI_OFDM_A 0x0068 /* TSSI for last 4 OFDM frames (32bit) */ 264#define B43_SHM_SH_TSSI_OFDM_G 0x0070 /* TSSI for last 4 OFDM frames (32bit) */ 265#define B43_TSSI_MAX 0x7F /* Max value for one TSSI value */ 266/* SHM_SHARED TX FIFO variables */ 267#define B43_SHM_SH_SIZE01 0x0098 /* TX FIFO size for FIFO 0 (low) and 1 (high) */ 268#define B43_SHM_SH_SIZE23 0x009A /* TX FIFO size for FIFO 2 and 3 */ 269#define B43_SHM_SH_SIZE45 0x009C /* TX FIFO size for FIFO 4 and 5 */ 270#define B43_SHM_SH_SIZE67 0x009E /* TX FIFO size for FIFO 6 and 7 */ 271/* SHM_SHARED background noise */ 272#define B43_SHM_SH_JSSI0 0x0088 /* Measure JSSI 0 */ 273#define B43_SHM_SH_JSSI1 0x008A /* Measure JSSI 1 */ 274#define B43_SHM_SH_JSSIAUX 0x008C /* Measure JSSI AUX */ 275/* SHM_SHARED crypto engine */ 276#define B43_SHM_SH_DEFAULTIV 0x003C /* Default IV location */ 277#define B43_SHM_SH_NRRXTRANS 0x003E /* # of soft RX transmitter addresses (max 8) */ 278#define B43_SHM_SH_KTP 0x0056 /* Key table pointer */ 279#define B43_SHM_SH_TKIPTSCTTAK 0x0318 280#define B43_SHM_SH_KEYIDXBLOCK 0x05D4 /* Key index/algorithm block (v4 firmware) */ 281#define B43_SHM_SH_PSM 0x05F4 /* PSM transmitter address match block (rev < 5) */ 282/* SHM_SHARED WME variables */ 283#define B43_SHM_SH_EDCFSTAT 0x000E /* EDCF status */ 284#define B43_SHM_SH_TXFCUR 0x0030 /* TXF current index */ 285#define B43_SHM_SH_EDCFQ 0x0240 /* EDCF Q info */ 286/* SHM_SHARED powersave mode related */ 287#define B43_SHM_SH_SLOTT 0x0010 /* Slot time */ 288#define B43_SHM_SH_DTIMPER 0x0012 /* DTIM period */ 289#define B43_SHM_SH_NOSLPZNATDTIM 0x004C /* NOSLPZNAT DTIM */ 290/* SHM_SHARED beacon/AP variables */ 291#define B43_SHM_SH_BT_BASE0 0x0068 /* Beacon template base 0 */ 292#define B43_SHM_SH_BTL0 0x0018 /* Beacon template length 0 */ 293#define B43_SHM_SH_BT_BASE1 0x0468 /* Beacon template base 1 */ 294#define B43_SHM_SH_BTL1 0x001A /* Beacon template length 1 */ 295#define B43_SHM_SH_BTSFOFF 0x001C /* Beacon TSF offset */ 296#define B43_SHM_SH_TIMBPOS 0x001E /* TIM B position in beacon */ 297#define B43_SHM_SH_DTIMP 0x0012 /* DTIP period */ 298#define B43_SHM_SH_MCASTCOOKIE 0x00A8 /* Last bcast/mcast frame ID */ 299#define B43_SHM_SH_SFFBLIM 0x0044 /* Short frame fallback retry limit */ 300#define B43_SHM_SH_LFFBLIM 0x0046 /* Long frame fallback retry limit */ 301#define B43_SHM_SH_BEACPHYCTL 0x0054 /* Beacon PHY TX control word (see PHY TX control) */ 302#define B43_SHM_SH_EXTNPHYCTL 0x00B0 /* Extended bytes for beacon PHY control (N) */ 303#define B43_SHM_SH_BCN_LI 0x00B6 /* beacon listen interval */ 304/* SHM_SHARED ACK/CTS control */ 305#define B43_SHM_SH_ACKCTSPHYCTL 0x0022 /* ACK/CTS PHY control word (see PHY TX control) */ 306/* SHM_SHARED probe response variables */ 307#define B43_SHM_SH_PRSSID 0x0160 /* Probe Response SSID */ 308#define B43_SHM_SH_PRSSIDLEN 0x0048 /* Probe Response SSID length */ 309#define B43_SHM_SH_PRTLEN 0x004A /* Probe Response template length */ 310#define B43_SHM_SH_PRMAXTIME 0x0074 /* Probe Response max time */ 311#define B43_SHM_SH_PRPHYCTL 0x0188 /* Probe Response PHY TX control word */ 312/* SHM_SHARED rate tables */ 313#define B43_SHM_SH_OFDMDIRECT 0x01C0 /* Pointer to OFDM direct map */ 314#define B43_SHM_SH_OFDMBASIC 0x01E0 /* Pointer to OFDM basic rate map */ 315#define B43_SHM_SH_CCKDIRECT 0x0200 /* Pointer to CCK direct map */ 316#define B43_SHM_SH_CCKBASIC 0x0220 /* Pointer to CCK basic rate map */ 317/* SHM_SHARED microcode soft registers */ 318#define B43_SHM_SH_UCODEREV 0x0000 /* Microcode revision */ 319#define B43_SHM_SH_UCODEPATCH 0x0002 /* Microcode patchlevel */ 320#define B43_SHM_SH_UCODEDATE 0x0004 /* Microcode date */ 321#define B43_SHM_SH_UCODETIME 0x0006 /* Microcode time */ 322#define B43_SHM_SH_UCODESTAT 0x0040 /* Microcode debug status code */ 323#define B43_SHM_SH_UCODESTAT_INVALID 0 324#define B43_SHM_SH_UCODESTAT_INIT 1 325#define B43_SHM_SH_UCODESTAT_ACTIVE 2 326#define B43_SHM_SH_UCODESTAT_SUSP 3 /* suspended */ 327#define B43_SHM_SH_UCODESTAT_SLEEP 4 /* asleep (PS) */ 328#define B43_SHM_SH_MAXBFRAMES 0x0080 /* Maximum number of frames in a burst */ 329#define B43_SHM_SH_SPUWKUP 0x0094 /* pre-wakeup for synth PU in us */ 330#define B43_SHM_SH_PRETBTT 0x0096 /* pre-TBTT in us */ 331/* SHM_SHARED tx iq workarounds */ 332#define B43_SHM_SH_NPHY_TXIQW0 0x0700 333#define B43_SHM_SH_NPHY_TXIQW1 0x0702 334#define B43_SHM_SH_NPHY_TXIQW2 0x0704 335#define B43_SHM_SH_NPHY_TXIQW3 0x0706 336/* SHM_SHARED tx pwr ctrl */ 337#define B43_SHM_SH_NPHY_TXPWR_INDX0 0x0708 338#define B43_SHM_SH_NPHY_TXPWR_INDX1 0x070E 339 340/* SHM_SCRATCH offsets */ 341#define B43_SHM_SC_MINCONT 0x0003 /* Minimum contention window */ 342#define B43_SHM_SC_MAXCONT 0x0004 /* Maximum contention window */ 343#define B43_SHM_SC_CURCONT 0x0005 /* Current contention window */ 344#define B43_SHM_SC_SRLIMIT 0x0006 /* Short retry count limit */ 345#define B43_SHM_SC_LRLIMIT 0x0007 /* Long retry count limit */ 346#define B43_SHM_SC_DTIMC 0x0008 /* Current DTIM count */ 347#define B43_SHM_SC_BTL0LEN 0x0015 /* Beacon 0 template length */ 348#define B43_SHM_SC_BTL1LEN 0x0016 /* Beacon 1 template length */ 349#define B43_SHM_SC_SCFB 0x0017 /* Short frame transmit count threshold for rate fallback */ 350#define B43_SHM_SC_LCFB 0x0018 /* Long frame transmit count threshold for rate fallback */ 351 352/* Hardware Radio Enable masks */ 353#define B43_MMIO_RADIO_HWENABLED_HI_MASK (1 << 16) 354#define B43_MMIO_RADIO_HWENABLED_LO_MASK (1 << 4) 355 356/* HostFlags. See b43_hf_read/write() */ 357#define B43_HF_ANTDIVHELP 0x000000000001ULL /* ucode antenna div helper */ 358#define B43_HF_SYMW 0x000000000002ULL /* G-PHY SYM workaround */ 359#define B43_HF_RXPULLW 0x000000000004ULL /* RX pullup workaround */ 360#define B43_HF_CCKBOOST 0x000000000008ULL /* 4dB CCK power boost (exclusive with OFDM boost) */ 361#define B43_HF_BTCOEX 0x000000000010ULL /* Bluetooth coexistance */ 362#define B43_HF_GDCW 0x000000000020ULL /* G-PHY DC canceller filter bw workaround */ 363#define B43_HF_OFDMPABOOST 0x000000000040ULL /* Enable PA gain boost for OFDM */ 364#define B43_HF_ACPR 0x000000000080ULL /* Disable for Japan, channel 14 */ 365#define B43_HF_EDCF 0x000000000100ULL /* on if WME and MAC suspended */ 366#define B43_HF_TSSIRPSMW 0x000000000200ULL /* TSSI reset PSM ucode workaround */ 367#define B43_HF_20IN40IQW 0x000000000200ULL /* 20 in 40 MHz I/Q workaround (rev >= 13 only) */ 368#define B43_HF_DSCRQ 0x000000000400ULL /* Disable slow clock request in ucode */ 369#define B43_HF_ACIW 0x000000000800ULL /* ACI workaround: shift bits by 2 on PHY CRS */ 370#define B43_HF_2060W 0x000000001000ULL /* 2060 radio workaround */ 371#define B43_HF_RADARW 0x000000002000ULL /* Radar workaround */ 372#define B43_HF_USEDEFKEYS 0x000000004000ULL /* Enable use of default keys */ 373#define B43_HF_AFTERBURNER 0x000000008000ULL /* Afterburner enabled */ 374#define B43_HF_BT4PRIOCOEX 0x000000010000ULL /* Bluetooth 4-priority coexistance */ 375#define B43_HF_FWKUP 0x000000020000ULL /* Fast wake-up ucode */ 376#define B43_HF_VCORECALC 0x000000040000ULL /* Force VCO recalculation when powering up synthpu */ 377#define B43_HF_PCISCW 0x000000080000ULL /* PCI slow clock workaround */ 378#define B43_HF_4318TSSI 0x000000200000ULL /* 4318 TSSI */ 379#define B43_HF_FBCMCFIFO 0x000000400000ULL /* Flush bcast/mcast FIFO immediately */ 380#define B43_HF_HWPCTL 0x000000800000ULL /* Enable hardwarre power control */ 381#define B43_HF_BTCOEXALT 0x000001000000ULL /* Bluetooth coexistance in alternate pins */ 382#define B43_HF_TXBTCHECK 0x000002000000ULL /* Bluetooth check during transmission */ 383#define B43_HF_SKCFPUP 0x000004000000ULL /* Skip CFP update */ 384#define B43_HF_N40W 0x000008000000ULL /* N PHY 40 MHz workaround (rev >= 13 only) */ 385#define B43_HF_ANTSEL 0x000020000000ULL /* Antenna selection (for testing antenna div.) */ 386#define B43_HF_BT3COEXT 0x000020000000ULL /* Bluetooth 3-wire coexistence (rev >= 13 only) */ 387#define B43_HF_BTCANT 0x000040000000ULL /* Bluetooth coexistence (antenna mode) (rev >= 13 only) */ 388#define B43_HF_ANTSELEN 0x000100000000ULL /* Antenna selection enabled (rev >= 13 only) */ 389#define B43_HF_ANTSELMODE 0x000200000000ULL /* Antenna selection mode (rev >= 13 only) */ 390#define B43_HF_MLADVW 0x001000000000ULL /* N PHY ML ADV workaround (rev >= 13 only) */ 391#define B43_HF_PR45960W 0x080000000000ULL /* PR 45960 workaround (rev >= 13 only) */ 392 393/* Firmware capabilities field in SHM (Opensource firmware only) */ 394#define B43_FWCAPA_HWCRYPTO 0x0001 395#define B43_FWCAPA_QOS 0x0002 396 397/* MacFilter offsets. */ 398#define B43_MACFILTER_SELF 0x0000 399#define B43_MACFILTER_BSSID 0x0003 400 401/* PowerControl */ 402#define B43_PCTL_IN 0xB0 403#define B43_PCTL_OUT 0xB4 404#define B43_PCTL_OUTENABLE 0xB8 405#define B43_PCTL_XTAL_POWERUP 0x40 406#define B43_PCTL_PLL_POWERDOWN 0x80 407 408/* PowerControl Clock Modes */ 409#define B43_PCTL_CLK_FAST 0x00 410#define B43_PCTL_CLK_SLOW 0x01 411#define B43_PCTL_CLK_DYNAMIC 0x02 412 413#define B43_PCTL_FORCE_SLOW 0x0800 414#define B43_PCTL_FORCE_PLL 0x1000 415#define B43_PCTL_DYN_XTAL 0x2000 416 417/* PHYVersioning */ 418#define B43_PHYTYPE_A 0x00 419#define B43_PHYTYPE_B 0x01 420#define B43_PHYTYPE_G 0x02 421#define B43_PHYTYPE_N 0x04 422#define B43_PHYTYPE_LP 0x05 423#define B43_PHYTYPE_SSLPN 0x06 424#define B43_PHYTYPE_HT 0x07 425#define B43_PHYTYPE_LCN 0x08 426#define B43_PHYTYPE_LCNXN 0x09 427#define B43_PHYTYPE_LCN40 0x0a 428#define B43_PHYTYPE_AC 0x0b 429 430/* PHYRegisters */ 431#define B43_PHY_ILT_A_CTRL 0x0072 432#define B43_PHY_ILT_A_DATA1 0x0073 433#define B43_PHY_ILT_A_DATA2 0x0074 434#define B43_PHY_G_LO_CONTROL 0x0810 435#define B43_PHY_ILT_G_CTRL 0x0472 436#define B43_PHY_ILT_G_DATA1 0x0473 437#define B43_PHY_ILT_G_DATA2 0x0474 438#define B43_PHY_A_PCTL 0x007B 439#define B43_PHY_G_PCTL 0x0029 440#define B43_PHY_A_CRS 0x0029 441#define B43_PHY_RADIO_BITFIELD 0x0401 442#define B43_PHY_G_CRS 0x0429 443#define B43_PHY_NRSSILT_CTRL 0x0803 444#define B43_PHY_NRSSILT_DATA 0x0804 445 446/* RadioRegisters */ 447#define B43_RADIOCTL_ID 0x01 448 449/* MAC Control bitfield */ 450#define B43_MACCTL_ENABLED 0x00000001 /* MAC Enabled */ 451#define B43_MACCTL_PSM_RUN 0x00000002 /* Run Microcode */ 452#define B43_MACCTL_PSM_JMP0 0x00000004 /* Microcode jump to 0 */ 453#define B43_MACCTL_SHM_ENABLED 0x00000100 /* SHM Enabled */ 454#define B43_MACCTL_SHM_UPPER 0x00000200 /* SHM Upper */ 455#define B43_MACCTL_IHR_ENABLED 0x00000400 /* IHR Region Enabled */ 456#define B43_MACCTL_PSM_DBG 0x00002000 /* Microcode debugging enabled */ 457#define B43_MACCTL_GPOUTSMSK 0x0000C000 /* GPOUT Select Mask */ 458#define B43_MACCTL_BE 0x00010000 /* Big Endian mode */ 459#define B43_MACCTL_INFRA 0x00020000 /* Infrastructure mode */ 460#define B43_MACCTL_AP 0x00040000 /* AccessPoint mode */ 461#define B43_MACCTL_RADIOLOCK 0x00080000 /* Radio lock */ 462#define B43_MACCTL_BEACPROMISC 0x00100000 /* Beacon Promiscuous */ 463#define B43_MACCTL_KEEP_BADPLCP 0x00200000 /* Keep frames with bad PLCP */ 464#define B43_MACCTL_PHY_LOCK 0x00200000 465#define B43_MACCTL_KEEP_CTL 0x00400000 /* Keep control frames */ 466#define B43_MACCTL_KEEP_BAD 0x00800000 /* Keep bad frames (FCS) */ 467#define B43_MACCTL_PROMISC 0x01000000 /* Promiscuous mode */ 468#define B43_MACCTL_HWPS 0x02000000 /* Hardware Power Saving */ 469#define B43_MACCTL_AWAKE 0x04000000 /* Device is awake */ 470#define B43_MACCTL_CLOSEDNET 0x08000000 /* Closed net (no SSID bcast) */ 471#define B43_MACCTL_TBTTHOLD 0x10000000 /* TBTT Hold */ 472#define B43_MACCTL_DISCTXSTAT 0x20000000 /* Discard TX status */ 473#define B43_MACCTL_DISCPMQ 0x40000000 /* Discard Power Management Queue */ 474#define B43_MACCTL_GMODE 0x80000000 /* G Mode */ 475 476/* MAC Command bitfield */ 477#define B43_MACCMD_BEACON0_VALID 0x00000001 /* Beacon 0 in template RAM is busy/valid */ 478#define B43_MACCMD_BEACON1_VALID 0x00000002 /* Beacon 1 in template RAM is busy/valid */ 479#define B43_MACCMD_DFQ_VALID 0x00000004 /* Directed frame queue valid (IBSS PS mode, ATIM) */ 480#define B43_MACCMD_CCA 0x00000008 /* Clear channel assessment */ 481#define B43_MACCMD_BGNOISE 0x00000010 /* Background noise */ 482 483/* B43_MMIO_PSM_PHY_HDR bits */ 484#define B43_PSM_HDR_MAC_PHY_RESET 0x00000001 485#define B43_PSM_HDR_MAC_PHY_CLOCK_EN 0x00000002 486#define B43_PSM_HDR_MAC_PHY_FORCE_CLK 0x00000004 487 488/* See BCMA_CLKCTLST_EXTRESREQ and BCMA_CLKCTLST_EXTRESST */ 489#define B43_BCMA_CLKCTLST_80211_PLL_REQ 0x00000100 490#define B43_BCMA_CLKCTLST_PHY_PLL_REQ 0x00000200 491#define B43_BCMA_CLKCTLST_80211_PLL_ST 0x01000000 492#define B43_BCMA_CLKCTLST_PHY_PLL_ST 0x02000000 493 494/* BCMA 802.11 core specific IO Control (BCMA_IOCTL) flags */ 495#define B43_BCMA_IOCTL_PHY_CLKEN 0x00000004 /* PHY Clock Enable */ 496#define B43_BCMA_IOCTL_PHY_RESET 0x00000008 /* PHY Reset */ 497#define B43_BCMA_IOCTL_MACPHYCLKEN 0x00000010 /* MAC PHY Clock Control Enable */ 498#define B43_BCMA_IOCTL_PLLREFSEL 0x00000020 /* PLL Frequency Reference Select */ 499#define B43_BCMA_IOCTL_PHY_BW 0x000000C0 /* PHY band width and clock speed mask (N-PHY+ only?) */ 500#define B43_BCMA_IOCTL_PHY_BW_10MHZ 0x00000000 /* 10 MHz bandwidth, 40 MHz PHY */ 501#define B43_BCMA_IOCTL_PHY_BW_20MHZ 0x00000040 /* 20 MHz bandwidth, 80 MHz PHY */ 502#define B43_BCMA_IOCTL_PHY_BW_40MHZ 0x00000080 /* 40 MHz bandwidth, 160 MHz PHY */ 503#define B43_BCMA_IOCTL_PHY_BW_80MHZ 0x000000C0 /* 80 MHz bandwidth */ 504#define B43_BCMA_IOCTL_DAC 0x00000300 /* Highspeed DAC mode control field */ 505#define B43_BCMA_IOCTL_GMODE 0x00002000 /* G Mode Enable */ 506 507/* BCMA 802.11 core specific IO status (BCMA_IOST) flags */ 508#define B43_BCMA_IOST_2G_PHY 0x00000001 /* 2.4G capable phy */ 509#define B43_BCMA_IOST_5G_PHY 0x00000002 /* 5G capable phy */ 510#define B43_BCMA_IOST_FASTCLKA 0x00000004 /* Fast Clock Available */ 511#define B43_BCMA_IOST_DUALB_PHY 0x00000008 /* Dualband phy */ 512 513/* 802.11 core specific TM State Low (SSB_TMSLOW) flags */ 514#define B43_TMSLOW_GMODE 0x20000000 /* G Mode Enable */ 515#define B43_TMSLOW_PHY_BANDWIDTH 0x00C00000 /* PHY band width and clock speed mask (N-PHY only) */ 516#define B43_TMSLOW_PHY_BANDWIDTH_10MHZ 0x00000000 /* 10 MHz bandwidth, 40 MHz PHY */ 517#define B43_TMSLOW_PHY_BANDWIDTH_20MHZ 0x00400000 /* 20 MHz bandwidth, 80 MHz PHY */ 518#define B43_TMSLOW_PHY_BANDWIDTH_40MHZ 0x00800000 /* 40 MHz bandwidth, 160 MHz PHY */ 519#define B43_TMSLOW_PLLREFSEL 0x00200000 /* PLL Frequency Reference Select (rev >= 5) */ 520#define B43_TMSLOW_MACPHYCLKEN 0x00100000 /* MAC PHY Clock Control Enable (rev >= 5) */ 521#define B43_TMSLOW_PHYRESET 0x00080000 /* PHY Reset */ 522#define B43_TMSLOW_PHYCLKEN 0x00040000 /* PHY Clock Enable */ 523 524/* 802.11 core specific TM State High (SSB_TMSHIGH) flags */ 525#define B43_TMSHIGH_DUALBAND_PHY 0x00080000 /* Dualband PHY available */ 526#define B43_TMSHIGH_FCLOCK 0x00040000 /* Fast Clock Available (rev >= 5) */ 527#define B43_TMSHIGH_HAVE_5GHZ_PHY 0x00020000 /* 5 GHz PHY available (rev >= 5) */ 528#define B43_TMSHIGH_HAVE_2GHZ_PHY 0x00010000 /* 2.4 GHz PHY available (rev >= 5) */ 529 530/* Generic-Interrupt reasons. */ 531#define B43_IRQ_MAC_SUSPENDED 0x00000001 532#define B43_IRQ_BEACON 0x00000002 533#define B43_IRQ_TBTT_INDI 0x00000004 534#define B43_IRQ_BEACON_TX_OK 0x00000008 535#define B43_IRQ_BEACON_CANCEL 0x00000010 536#define B43_IRQ_ATIM_END 0x00000020 537#define B43_IRQ_PMQ 0x00000040 538#define B43_IRQ_PIO_WORKAROUND 0x00000100 539#define B43_IRQ_MAC_TXERR 0x00000200 540#define B43_IRQ_PHY_TXERR 0x00000800 541#define B43_IRQ_PMEVENT 0x00001000 542#define B43_IRQ_TIMER0 0x00002000 543#define B43_IRQ_TIMER1 0x00004000 544#define B43_IRQ_DMA 0x00008000 545#define B43_IRQ_TXFIFO_FLUSH_OK 0x00010000 546#define B43_IRQ_CCA_MEASURE_OK 0x00020000 547#define B43_IRQ_NOISESAMPLE_OK 0x00040000 548#define B43_IRQ_UCODE_DEBUG 0x08000000 549#define B43_IRQ_RFKILL 0x10000000 550#define B43_IRQ_TX_OK 0x20000000 551#define B43_IRQ_PHY_G_CHANGED 0x40000000 552#define B43_IRQ_TIMEOUT 0x80000000 553 554#define B43_IRQ_ALL 0xFFFFFFFF 555#define B43_IRQ_MASKTEMPLATE (B43_IRQ_TBTT_INDI | \ 556 B43_IRQ_ATIM_END | \ 557 B43_IRQ_PMQ | \ 558 B43_IRQ_MAC_TXERR | \ 559 B43_IRQ_PHY_TXERR | \ 560 B43_IRQ_DMA | \ 561 B43_IRQ_TXFIFO_FLUSH_OK | \ 562 B43_IRQ_NOISESAMPLE_OK | \ 563 B43_IRQ_UCODE_DEBUG | \ 564 B43_IRQ_RFKILL | \ 565 B43_IRQ_TX_OK) 566 567/* The firmware register to fetch the debug-IRQ reason from. */ 568#define B43_DEBUGIRQ_REASON_REG 63 569/* Debug-IRQ reasons. */ 570#define B43_DEBUGIRQ_PANIC 0 /* The firmware panic'ed */ 571#define B43_DEBUGIRQ_DUMP_SHM 1 /* Dump shared SHM */ 572#define B43_DEBUGIRQ_DUMP_REGS 2 /* Dump the microcode registers */ 573#define B43_DEBUGIRQ_MARKER 3 /* A "marker" was thrown by the firmware. */ 574#define B43_DEBUGIRQ_ACK 0xFFFF /* The host writes that to ACK the IRQ */ 575 576/* The firmware register that contains the "marker" line. */ 577#define B43_MARKER_ID_REG 2 578#define B43_MARKER_LINE_REG 3 579 580/* The firmware register to fetch the panic reason from. */ 581#define B43_FWPANIC_REASON_REG 3 582/* Firmware panic reason codes */ 583#define B43_FWPANIC_DIE 0 /* Firmware died. Don't auto-restart it. */ 584#define B43_FWPANIC_RESTART 1 /* Firmware died. Schedule a controller reset. */ 585 586/* The firmware register that contains the watchdog counter. */ 587#define B43_WATCHDOG_REG 1 588 589/* Device specific rate values. 590 * The actual values defined here are (rate_in_mbps * 2). 591 * Some code depends on this. Don't change it. */ 592#define B43_CCK_RATE_1MB 0x02 593#define B43_CCK_RATE_2MB 0x04 594#define B43_CCK_RATE_5MB 0x0B 595#define B43_CCK_RATE_11MB 0x16 596#define B43_OFDM_RATE_6MB 0x0C 597#define B43_OFDM_RATE_9MB 0x12 598#define B43_OFDM_RATE_12MB 0x18 599#define B43_OFDM_RATE_18MB 0x24 600#define B43_OFDM_RATE_24MB 0x30 601#define B43_OFDM_RATE_36MB 0x48 602#define B43_OFDM_RATE_48MB 0x60 603#define B43_OFDM_RATE_54MB 0x6C 604/* Convert a b43 rate value to a rate in 100kbps */ 605#define B43_RATE_TO_BASE100KBPS(rate) (((rate) * 10) / 2) 606 607#define B43_DEFAULT_SHORT_RETRY_LIMIT 7 608#define B43_DEFAULT_LONG_RETRY_LIMIT 4 609 610#define B43_PHY_TX_BADNESS_LIMIT 1000 611 612/* Max size of a security key */ 613#define B43_SEC_KEYSIZE 16 614/* Max number of group keys */ 615#define B43_NR_GROUP_KEYS 4 616/* Max number of pairwise keys */ 617#define B43_NR_PAIRWISE_KEYS 50 618/* Security algorithms. */ 619enum { 620 B43_SEC_ALGO_NONE = 0, /* unencrypted, as of TX header. */ 621 B43_SEC_ALGO_WEP40, 622 B43_SEC_ALGO_TKIP, 623 B43_SEC_ALGO_AES, 624 B43_SEC_ALGO_WEP104, 625 B43_SEC_ALGO_AES_LEGACY, 626}; 627 628struct b43_dmaring; 629 630/* The firmware file header */ 631#define B43_FW_TYPE_UCODE 'u' 632#define B43_FW_TYPE_PCM 'p' 633#define B43_FW_TYPE_IV 'i' 634struct b43_fw_header { 635 /* File type */ 636 u8 type; 637 /* File format version */ 638 u8 ver; 639 u8 __padding[2]; 640 /* Size of the data. For ucode and PCM this is in bytes. 641 * For IV this is number-of-ivs. */ 642 __be32 size; 643} __packed; 644 645/* Initial Value file format */ 646#define B43_IV_OFFSET_MASK 0x7FFF 647#define B43_IV_32BIT 0x8000 648struct b43_iv { 649 __be16 offset_size; 650 union { 651 __be16 d16; 652 __be32 d32; 653 } data __packed; 654} __packed; 655 656 657/* Data structures for DMA transmission, per 80211 core. */ 658struct b43_dma { 659 struct b43_dmaring *tx_ring_AC_BK; /* Background */ 660 struct b43_dmaring *tx_ring_AC_BE; /* Best Effort */ 661 struct b43_dmaring *tx_ring_AC_VI; /* Video */ 662 struct b43_dmaring *tx_ring_AC_VO; /* Voice */ 663 struct b43_dmaring *tx_ring_mcast; /* Multicast */ 664 665 struct b43_dmaring *rx_ring; 666 667 u32 translation; /* Routing bits */ 668 bool translation_in_low; /* Should translation bit go into low addr? */ 669 bool parity; /* Check for parity */ 670}; 671 672struct b43_pio_txqueue; 673struct b43_pio_rxqueue; 674 675/* Data structures for PIO transmission, per 80211 core. */ 676struct b43_pio { 677 struct b43_pio_txqueue *tx_queue_AC_BK; /* Background */ 678 struct b43_pio_txqueue *tx_queue_AC_BE; /* Best Effort */ 679 struct b43_pio_txqueue *tx_queue_AC_VI; /* Video */ 680 struct b43_pio_txqueue *tx_queue_AC_VO; /* Voice */ 681 struct b43_pio_txqueue *tx_queue_mcast; /* Multicast */ 682 683 struct b43_pio_rxqueue *rx_queue; 684}; 685 686/* Context information for a noise calculation (Link Quality). */ 687struct b43_noise_calculation { 688 bool calculation_running; 689 u8 nr_samples; 690 s8 samples[8][4]; 691}; 692 693struct b43_stats { 694 u8 link_noise; 695}; 696 697struct b43_key { 698 /* If keyconf is NULL, this key is disabled. 699 * keyconf is a cookie. Don't derefenrence it outside of the set_key 700 * path, because b43 doesn't own it. */ 701 struct ieee80211_key_conf *keyconf; 702 u8 algorithm; 703}; 704 705/* SHM offsets to the QOS data structures for the 4 different queues. */ 706#define B43_QOS_QUEUE_NUM 4 707#define B43_QOS_PARAMS(queue) (B43_SHM_SH_EDCFQ + \ 708 (B43_NR_QOSPARAMS * sizeof(u16) * (queue))) 709#define B43_QOS_BACKGROUND B43_QOS_PARAMS(0) 710#define B43_QOS_BESTEFFORT B43_QOS_PARAMS(1) 711#define B43_QOS_VIDEO B43_QOS_PARAMS(2) 712#define B43_QOS_VOICE B43_QOS_PARAMS(3) 713 714/* QOS parameter hardware data structure offsets. */ 715#define B43_NR_QOSPARAMS 16 716enum { 717 B43_QOSPARAM_TXOP = 0, 718 B43_QOSPARAM_CWMIN, 719 B43_QOSPARAM_CWMAX, 720 B43_QOSPARAM_CWCUR, 721 B43_QOSPARAM_AIFS, 722 B43_QOSPARAM_BSLOTS, 723 B43_QOSPARAM_REGGAP, 724 B43_QOSPARAM_STATUS, 725}; 726 727/* QOS parameters for a queue. */ 728struct b43_qos_params { 729 /* The QOS parameters */ 730 struct ieee80211_tx_queue_params p; 731}; 732 733struct b43_wl; 734 735/* The type of the firmware file. */ 736enum b43_firmware_file_type { 737 B43_FWTYPE_PROPRIETARY, 738 B43_FWTYPE_OPENSOURCE, 739 B43_NR_FWTYPES, 740}; 741 742/* Context data for fetching firmware. */ 743struct b43_request_fw_context { 744 /* The device we are requesting the fw for. */ 745 struct b43_wldev *dev; 746 /* a pointer to the firmware object */ 747 const struct firmware *blob; 748 /* The type of firmware to request. */ 749 enum b43_firmware_file_type req_type; 750 /* Error messages for each firmware type. */ 751 char errors[B43_NR_FWTYPES][128]; 752 /* Temporary buffer for storing the firmware name. */ 753 char fwname[64]; 754 /* A fatal error occurred while requesting. Firmware request 755 * can not continue, as any other request will also fail. */ 756 int fatal_failure; 757}; 758 759/* In-memory representation of a cached microcode file. */ 760struct b43_firmware_file { 761 const char *filename; 762 const struct firmware *data; 763 /* Type of the firmware file name. Note that this does only indicate 764 * the type by the firmware name. NOT the file contents. 765 * If you want to check for proprietary vs opensource, use (struct b43_firmware)->opensource 766 * instead! The (struct b43_firmware)->opensource flag is derived from the actual firmware 767 * binary code, not just the filename. 768 */ 769 enum b43_firmware_file_type type; 770}; 771 772enum b43_firmware_hdr_format { 773 B43_FW_HDR_598, 774 B43_FW_HDR_410, 775 B43_FW_HDR_351, 776}; 777 778/* Pointers to the firmware data and meta information about it. */ 779struct b43_firmware { 780 /* Microcode */ 781 struct b43_firmware_file ucode; 782 /* PCM code */ 783 struct b43_firmware_file pcm; 784 /* Initial MMIO values for the firmware */ 785 struct b43_firmware_file initvals; 786 /* Initial MMIO values for the firmware, band-specific */ 787 struct b43_firmware_file initvals_band; 788 789 /* Firmware revision */ 790 u16 rev; 791 /* Firmware patchlevel */ 792 u16 patch; 793 794 /* Format of header used by firmware */ 795 enum b43_firmware_hdr_format hdr_format; 796 797 /* Set to true, if we are using an opensource firmware. 798 * Use this to check for proprietary vs opensource. */ 799 bool opensource; 800 /* Set to true, if the core needs a PCM firmware, but 801 * we failed to load one. This is always false for 802 * core rev > 10, as these don't need PCM firmware. */ 803 bool pcm_request_failed; 804}; 805 806enum b43_band { 807 B43_BAND_2G = 0, 808 B43_BAND_5G_LO = 1, 809 B43_BAND_5G_MI = 2, 810 B43_BAND_5G_HI = 3, 811}; 812 813/* Device (802.11 core) initialization status. */ 814enum { 815 B43_STAT_UNINIT = 0, /* Uninitialized. */ 816 B43_STAT_INITIALIZED = 1, /* Initialized, but not started, yet. */ 817 B43_STAT_STARTED = 2, /* Up and running. */ 818}; 819#define b43_status(wldev) atomic_read(&(wldev)->__init_status) 820#define b43_set_status(wldev, stat) do { \ 821 atomic_set(&(wldev)->__init_status, (stat)); \ 822 smp_wmb(); \ 823 } while (0) 824 825/* Data structure for one wireless device (802.11 core) */ 826struct b43_wldev { 827 struct b43_bus_dev *dev; 828 struct b43_wl *wl; 829 /* a completion event structure needed if this call is asynchronous */ 830 struct completion fw_load_complete; 831 832 /* The device initialization status. 833 * Use b43_status() to query. */ 834 atomic_t __init_status; 835 836 bool bad_frames_preempt; /* Use "Bad Frames Preemption" (default off) */ 837 bool dfq_valid; /* Directed frame queue valid (IBSS PS mode, ATIM) */ 838 bool radio_hw_enable; /* saved state of radio hardware enabled state */ 839 bool qos_enabled; /* TRUE, if QoS is used. */ 840 bool hwcrypto_enabled; /* TRUE, if HW crypto acceleration is enabled. */ 841 bool use_pio; /* TRUE if next init should use PIO */ 842 843 /* PHY/Radio device. */ 844 struct b43_phy phy; 845 846 union { 847 /* DMA engines. */ 848 struct b43_dma dma; 849 /* PIO engines. */ 850 struct b43_pio pio; 851 }; 852 /* Use b43_using_pio_transfers() to check whether we are using 853 * DMA or PIO data transfers. */ 854 bool __using_pio_transfers; 855 856 /* Various statistics about the physical device. */ 857 struct b43_stats stats; 858 859 /* Reason code of the last interrupt. */ 860 u32 irq_reason; 861 u32 dma_reason[6]; 862 /* The currently active generic-interrupt mask. */ 863 u32 irq_mask; 864 865 /* Link Quality calculation context. */ 866 struct b43_noise_calculation noisecalc; 867 /* if > 0 MAC is suspended. if == 0 MAC is enabled. */ 868 int mac_suspended; 869 870 /* Periodic tasks */ 871 struct delayed_work periodic_work; 872 unsigned int periodic_state; 873 874 struct work_struct restart_work; 875 876 /* encryption/decryption */ 877 u16 ktp; /* Key table pointer */ 878 struct b43_key key[B43_NR_GROUP_KEYS * 2 + B43_NR_PAIRWISE_KEYS]; 879 880 /* Firmware data */ 881 struct b43_firmware fw; 882 883 /* Devicelist in struct b43_wl (all 802.11 cores) */ 884 struct list_head list; 885 886 /* Debugging stuff follows. */ 887#ifdef CONFIG_B43_DEBUG 888 struct b43_dfsentry *dfsentry; 889 unsigned int irq_count; 890 unsigned int irq_bit_count[32]; 891 unsigned int tx_count; 892 unsigned int rx_count; 893#endif 894}; 895 896/* Data structure for the WLAN parts (802.11 cores) of the b43 chip. */ 897struct b43_wl { 898 /* Pointer to the active wireless device on this chip */ 899 struct b43_wldev *current_dev; 900 /* Pointer to the ieee80211 hardware data structure */ 901 struct ieee80211_hw *hw; 902 903 /* Global driver mutex. Every operation must run with this mutex locked. */ 904 struct mutex mutex; 905 /* Hard-IRQ spinlock. This lock protects things used in the hard-IRQ 906 * handler, only. This basically is just the IRQ mask register. */ 907 spinlock_t hardirq_lock; 908 909 /* Set this if we call ieee80211_register_hw() and check if we call 910 * ieee80211_unregister_hw(). */ 911 bool hw_registred; 912 913 /* We can only have one operating interface (802.11 core) 914 * at a time. General information about this interface follows. 915 */ 916 917 struct ieee80211_vif *vif; 918 /* The MAC address of the operating interface. */ 919 u8 mac_addr[ETH_ALEN]; 920 /* Current BSSID */ 921 u8 bssid[ETH_ALEN]; 922 /* Interface type. (NL80211_IFTYPE_XXX) */ 923 int if_type; 924 /* Is the card operating in AP, STA or IBSS mode? */ 925 bool operating; 926 /* filter flags */ 927 unsigned int filter_flags; 928 /* Stats about the wireless interface */ 929 struct ieee80211_low_level_stats ieee_stats; 930 931#ifdef CONFIG_B43_HWRNG 932 struct hwrng rng; 933 bool rng_initialized; 934 char rng_name[30 + 1]; 935#endif /* CONFIG_B43_HWRNG */ 936 937 bool radiotap_enabled; 938 bool radio_enabled; 939 940 /* The beacon we are currently using (AP or IBSS mode). */ 941 struct sk_buff *current_beacon; 942 bool beacon0_uploaded; 943 bool beacon1_uploaded; 944 bool beacon_templates_virgin; /* Never wrote the templates? */ 945 struct work_struct beacon_update_trigger; 946 spinlock_t beacon_lock; 947 948 /* The current QOS parameters for the 4 queues. */ 949 struct b43_qos_params qos_params[B43_QOS_QUEUE_NUM]; 950 951 /* Work for adjustment of the transmission power. 952 * This is scheduled when we determine that the actual TX output 953 * power doesn't match what we want. */ 954 struct work_struct txpower_adjust_work; 955 956 /* Packet transmit work */ 957 struct work_struct tx_work; 958 959 /* Queue of packets to be transmitted. */ 960 struct sk_buff_head tx_queue[B43_QOS_QUEUE_NUM]; 961 962 /* Flag that implement the queues stopping. */ 963 bool tx_queue_stopped[B43_QOS_QUEUE_NUM]; 964 965 /* firmware loading work */ 966 struct work_struct firmware_load; 967 968 /* The device LEDs. */ 969 struct b43_leds leds; 970 971 /* Kmalloc'ed scratch space for PIO TX/RX. Protected by wl->mutex. */ 972 u8 pio_scratchspace[118] __attribute__((__aligned__(8))); 973 u8 pio_tailspace[4] __attribute__((__aligned__(8))); 974}; 975 976static inline struct b43_wl *hw_to_b43_wl(struct ieee80211_hw *hw) 977{ 978 return hw->priv; 979} 980 981static inline struct b43_wldev *dev_to_b43_wldev(struct device *dev) 982{ 983 struct ssb_device *ssb_dev = dev_to_ssb_dev(dev); 984 return ssb_get_drvdata(ssb_dev); 985} 986 987/* Is the device operating in a specified mode (NL80211_IFTYPE_XXX). */ 988static inline int b43_is_mode(struct b43_wl *wl, int type) 989{ 990 return (wl->operating && wl->if_type == type); 991} 992 993/** 994 * b43_current_band - Returns the currently used band. 995 * Returns one of IEEE80211_BAND_2GHZ and IEEE80211_BAND_5GHZ. 996 */ 997static inline enum ieee80211_band b43_current_band(struct b43_wl *wl) 998{ 999 return wl->hw->conf.chandef.chan->band; 1000} 1001 1002static inline int b43_bus_may_powerdown(struct b43_wldev *wldev) 1003{ 1004 return wldev->dev->bus_may_powerdown(wldev->dev); 1005} 1006static inline int b43_bus_powerup(struct b43_wldev *wldev, bool dynamic_pctl) 1007{ 1008 return wldev->dev->bus_powerup(wldev->dev, dynamic_pctl); 1009} 1010static inline int b43_device_is_enabled(struct b43_wldev *wldev) 1011{ 1012 return wldev->dev->device_is_enabled(wldev->dev); 1013} 1014static inline void b43_device_enable(struct b43_wldev *wldev, 1015 u32 core_specific_flags) 1016{ 1017 wldev->dev->device_enable(wldev->dev, core_specific_flags); 1018} 1019static inline void b43_device_disable(struct b43_wldev *wldev, 1020 u32 core_specific_flags) 1021{ 1022 wldev->dev->device_disable(wldev->dev, core_specific_flags); 1023} 1024 1025static inline u16 b43_read16(struct b43_wldev *dev, u16 offset) 1026{ 1027 return dev->dev->read16(dev->dev, offset); 1028} 1029 1030static inline void b43_write16(struct b43_wldev *dev, u16 offset, u16 value) 1031{ 1032 dev->dev->write16(dev->dev, offset, value); 1033} 1034 1035/* To optimize this check for flush_writes on BCM47XX_BCMA only. */ 1036static inline void b43_write16f(struct b43_wldev *dev, u16 offset, u16 value) 1037{ 1038 b43_write16(dev, offset, value); 1039#if defined(CONFIG_BCM47XX_BCMA) 1040 if (dev->dev->flush_writes) 1041 b43_read16(dev, offset); 1042#endif 1043} 1044 1045static inline void b43_maskset16(struct b43_wldev *dev, u16 offset, u16 mask, 1046 u16 set) 1047{ 1048 b43_write16(dev, offset, (b43_read16(dev, offset) & mask) | set); 1049} 1050 1051static inline u32 b43_read32(struct b43_wldev *dev, u16 offset) 1052{ 1053 return dev->dev->read32(dev->dev, offset); 1054} 1055 1056static inline void b43_write32(struct b43_wldev *dev, u16 offset, u32 value) 1057{ 1058 dev->dev->write32(dev->dev, offset, value); 1059} 1060 1061static inline void b43_maskset32(struct b43_wldev *dev, u16 offset, u32 mask, 1062 u32 set) 1063{ 1064 b43_write32(dev, offset, (b43_read32(dev, offset) & mask) | set); 1065} 1066 1067static inline void b43_block_read(struct b43_wldev *dev, void *buffer, 1068 size_t count, u16 offset, u8 reg_width) 1069{ 1070 dev->dev->block_read(dev->dev, buffer, count, offset, reg_width); 1071} 1072 1073static inline void b43_block_write(struct b43_wldev *dev, const void *buffer, 1074 size_t count, u16 offset, u8 reg_width) 1075{ 1076 dev->dev->block_write(dev->dev, buffer, count, offset, reg_width); 1077} 1078 1079static inline bool b43_using_pio_transfers(struct b43_wldev *dev) 1080{ 1081 return dev->__using_pio_transfers; 1082} 1083 1084/* Message printing */ 1085__printf(2, 3) void b43info(struct b43_wl *wl, const char *fmt, ...); 1086__printf(2, 3) void b43err(struct b43_wl *wl, const char *fmt, ...); 1087__printf(2, 3) void b43warn(struct b43_wl *wl, const char *fmt, ...); 1088__printf(2, 3) void b43dbg(struct b43_wl *wl, const char *fmt, ...); 1089 1090 1091/* A WARN_ON variant that vanishes when b43 debugging is disabled. 1092 * This _also_ evaluates the arg with debugging disabled. */ 1093#if B43_DEBUG 1094# define B43_WARN_ON(x) WARN_ON(x) 1095#else 1096static inline bool __b43_warn_on_dummy(bool x) { return x; } 1097# define B43_WARN_ON(x) __b43_warn_on_dummy(unlikely(!!(x))) 1098#endif 1099 1100/* Convert an integer to a Q5.2 value */ 1101#define INT_TO_Q52(i) ((i) << 2) 1102/* Convert a Q5.2 value to an integer (precision loss!) */ 1103#define Q52_TO_INT(q52) ((q52) >> 2) 1104/* Macros for printing a value in Q5.2 format */ 1105#define Q52_FMT "%u.%u" 1106#define Q52_ARG(q52) Q52_TO_INT(q52), ((((q52) & 0x3) * 100) / 4) 1107 1108#endif /* B43_H_ */ 1109