1/******************************************************************************
2 *
3 * This file is provided under a dual BSD/GPLv2 license.  When using or
4 * redistributing this file, you may do so under either license.
5 *
6 * GPL LICENSE SUMMARY
7 *
8 * Copyright(c) 2007 - 2014 Intel Corporation. All rights reserved.
9 * Copyright(c) 2013 - 2015 Intel Mobile Communications GmbH
10 *
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of version 2 of the GNU General Public License as
13 * published by the Free Software Foundation.
14 *
15 * This program is distributed in the hope that it will be useful, but
16 * WITHOUT ANY WARRANTY; without even the implied warranty of
17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
18 * General Public License for more details.
19 *
20 * You should have received a copy of the GNU General Public License
21 * along with this program; if not, write to the Free Software
22 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
23 * USA
24 *
25 * The full GNU General Public License is included in this distribution
26 * in the file called COPYING.
27 *
28 * Contact Information:
29 *  Intel Linux Wireless <ilw@linux.intel.com>
30 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
31 *
32 * BSD LICENSE
33 *
34 * Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved.
35 * Copyright(c) 2013 - 2015 Intel Mobile Communications GmbH
36 * All rights reserved.
37 *
38 * Redistribution and use in source and binary forms, with or without
39 * modification, are permitted provided that the following conditions
40 * are met:
41 *
42 *  * Redistributions of source code must retain the above copyright
43 *    notice, this list of conditions and the following disclaimer.
44 *  * Redistributions in binary form must reproduce the above copyright
45 *    notice, this list of conditions and the following disclaimer in
46 *    the documentation and/or other materials provided with the
47 *    distribution.
48 *  * Neither the name Intel Corporation nor the names of its
49 *    contributors may be used to endorse or promote products derived
50 *    from this software without specific prior written permission.
51 *
52 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
53 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
54 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
55 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
56 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
57 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
58 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
59 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
60 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
61 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
62 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
63 *
64 *****************************************************************************/
65#ifndef __iwl_trans_h__
66#define __iwl_trans_h__
67
68#include <linux/ieee80211.h>
69#include <linux/mm.h> /* for page_address */
70#include <linux/lockdep.h>
71
72#include "iwl-debug.h"
73#include "iwl-config.h"
74#include "iwl-fw.h"
75#include "iwl-op-mode.h"
76
77/**
78 * DOC: Transport layer - what is it ?
79 *
80 * The transport layer is the layer that deals with the HW directly. It provides
81 * an abstraction of the underlying HW to the upper layer. The transport layer
82 * doesn't provide any policy, algorithm or anything of this kind, but only
83 * mechanisms to make the HW do something. It is not completely stateless but
84 * close to it.
85 * We will have an implementation for each different supported bus.
86 */
87
88/**
89 * DOC: Life cycle of the transport layer
90 *
91 * The transport layer has a very precise life cycle.
92 *
93 *	1) A helper function is called during the module initialization and
94 *	   registers the bus driver's ops with the transport's alloc function.
95 *	2) Bus's probe calls to the transport layer's allocation functions.
96 *	   Of course this function is bus specific.
97 *	3) This allocation functions will spawn the upper layer which will
98 *	   register mac80211.
99 *
100 *	4) At some point (i.e. mac80211's start call), the op_mode will call
101 *	   the following sequence:
102 *	   start_hw
103 *	   start_fw
104 *
105 *	5) Then when finished (or reset):
106 *	   stop_device
107 *
108 *	6) Eventually, the free function will be called.
109 */
110
111/**
112 * DOC: Host command section
113 *
114 * A host command is a command issued by the upper layer to the fw. There are
115 * several versions of fw that have several APIs. The transport layer is
116 * completely agnostic to these differences.
117 * The transport does provide helper functionality (i.e. SYNC / ASYNC mode),
118 */
119#define SEQ_TO_QUEUE(s)	(((s) >> 8) & 0x1f)
120#define QUEUE_TO_SEQ(q)	(((q) & 0x1f) << 8)
121#define SEQ_TO_INDEX(s)	((s) & 0xff)
122#define INDEX_TO_SEQ(i)	((i) & 0xff)
123#define SEQ_RX_FRAME	cpu_to_le16(0x8000)
124
125/**
126 * struct iwl_cmd_header
127 *
128 * This header format appears in the beginning of each command sent from the
129 * driver, and each response/notification received from uCode.
130 */
131struct iwl_cmd_header {
132	u8 cmd;		/* Command ID:  REPLY_RXON, etc. */
133	u8 flags;	/* 0:5 reserved, 6 abort, 7 internal */
134	/*
135	 * The driver sets up the sequence number to values of its choosing.
136	 * uCode does not use this value, but passes it back to the driver
137	 * when sending the response to each driver-originated command, so
138	 * the driver can match the response to the command.  Since the values
139	 * don't get used by uCode, the driver may set up an arbitrary format.
140	 *
141	 * There is one exception:  uCode sets bit 15 when it originates
142	 * the response/notification, i.e. when the response/notification
143	 * is not a direct response to a command sent by the driver.  For
144	 * example, uCode issues REPLY_RX when it sends a received frame
145	 * to the driver; it is not a direct response to any driver command.
146	 *
147	 * The Linux driver uses the following format:
148	 *
149	 *  0:7		tfd index - position within TX queue
150	 *  8:12	TX queue id
151	 *  13:14	reserved
152	 *  15		unsolicited RX or uCode-originated notification
153	 */
154	__le16 sequence;
155} __packed;
156
157/* iwl_cmd_header flags value */
158#define IWL_CMD_FAILED_MSK 0x40
159
160
161#define FH_RSCSR_FRAME_SIZE_MSK		0x00003FFF	/* bits 0-13 */
162#define FH_RSCSR_FRAME_INVALID		0x55550000
163#define FH_RSCSR_FRAME_ALIGN		0x40
164
165struct iwl_rx_packet {
166	/*
167	 * The first 4 bytes of the RX frame header contain both the RX frame
168	 * size and some flags.
169	 * Bit fields:
170	 * 31:    flag flush RB request
171	 * 30:    flag ignore TC (terminal counter) request
172	 * 29:    flag fast IRQ request
173	 * 28-14: Reserved
174	 * 13-00: RX frame size
175	 */
176	__le32 len_n_flags;
177	struct iwl_cmd_header hdr;
178	u8 data[];
179} __packed;
180
181static inline u32 iwl_rx_packet_len(const struct iwl_rx_packet *pkt)
182{
183	return le32_to_cpu(pkt->len_n_flags) & FH_RSCSR_FRAME_SIZE_MSK;
184}
185
186static inline u32 iwl_rx_packet_payload_len(const struct iwl_rx_packet *pkt)
187{
188	return iwl_rx_packet_len(pkt) - sizeof(pkt->hdr);
189}
190
191/**
192 * enum CMD_MODE - how to send the host commands ?
193 *
194 * @CMD_ASYNC: Return right away and don't wait for the response
195 * @CMD_WANT_SKB: Not valid with CMD_ASYNC. The caller needs the buffer of
196 *	the response. The caller needs to call iwl_free_resp when done.
197 * @CMD_HIGH_PRIO: The command is high priority - it goes to the front of the
198 *	command queue, but after other high priority commands. Valid only
199 *	with CMD_ASYNC.
200 * @CMD_SEND_IN_IDLE: The command should be sent even when the trans is idle.
201 * @CMD_MAKE_TRANS_IDLE: The command response should mark the trans as idle.
202 * @CMD_WAKE_UP_TRANS: The command response should wake up the trans
203 *	(i.e. mark it as non-idle).
204 */
205enum CMD_MODE {
206	CMD_ASYNC		= BIT(0),
207	CMD_WANT_SKB		= BIT(1),
208	CMD_SEND_IN_RFKILL	= BIT(2),
209	CMD_HIGH_PRIO		= BIT(3),
210	CMD_SEND_IN_IDLE	= BIT(4),
211	CMD_MAKE_TRANS_IDLE	= BIT(5),
212	CMD_WAKE_UP_TRANS	= BIT(6),
213};
214
215#define DEF_CMD_PAYLOAD_SIZE 320
216
217/**
218 * struct iwl_device_cmd
219 *
220 * For allocation of the command and tx queues, this establishes the overall
221 * size of the largest command we send to uCode, except for commands that
222 * aren't fully copied and use other TFD space.
223 */
224struct iwl_device_cmd {
225	struct iwl_cmd_header hdr;	/* uCode API */
226	u8 payload[DEF_CMD_PAYLOAD_SIZE];
227} __packed;
228
229#define TFD_MAX_PAYLOAD_SIZE (sizeof(struct iwl_device_cmd))
230
231/*
232 * number of transfer buffers (fragments) per transmit frame descriptor;
233 * this is just the driver's idea, the hardware supports 20
234 */
235#define IWL_MAX_CMD_TBS_PER_TFD	2
236
237/**
238 * struct iwl_hcmd_dataflag - flag for each one of the chunks of the command
239 *
240 * @IWL_HCMD_DFL_NOCOPY: By default, the command is copied to the host command's
241 *	ring. The transport layer doesn't map the command's buffer to DMA, but
242 *	rather copies it to a previously allocated DMA buffer. This flag tells
243 *	the transport layer not to copy the command, but to map the existing
244 *	buffer (that is passed in) instead. This saves the memcpy and allows
245 *	commands that are bigger than the fixed buffer to be submitted.
246 *	Note that a TFD entry after a NOCOPY one cannot be a normal copied one.
247 * @IWL_HCMD_DFL_DUP: Only valid without NOCOPY, duplicate the memory for this
248 *	chunk internally and free it again after the command completes. This
249 *	can (currently) be used only once per command.
250 *	Note that a TFD entry after a DUP one cannot be a normal copied one.
251 */
252enum iwl_hcmd_dataflag {
253	IWL_HCMD_DFL_NOCOPY	= BIT(0),
254	IWL_HCMD_DFL_DUP	= BIT(1),
255};
256
257/**
258 * struct iwl_host_cmd - Host command to the uCode
259 *
260 * @data: array of chunks that composes the data of the host command
261 * @resp_pkt: response packet, if %CMD_WANT_SKB was set
262 * @_rx_page_order: (internally used to free response packet)
263 * @_rx_page_addr: (internally used to free response packet)
264 * @handler_status: return value of the handler of the command
265 *	(put in setup_rx_handlers) - valid for SYNC mode only
266 * @flags: can be CMD_*
267 * @len: array of the lengths of the chunks in data
268 * @dataflags: IWL_HCMD_DFL_*
269 * @id: id of the host command
270 */
271struct iwl_host_cmd {
272	const void *data[IWL_MAX_CMD_TBS_PER_TFD];
273	struct iwl_rx_packet *resp_pkt;
274	unsigned long _rx_page_addr;
275	u32 _rx_page_order;
276	int handler_status;
277
278	u32 flags;
279	u16 len[IWL_MAX_CMD_TBS_PER_TFD];
280	u8 dataflags[IWL_MAX_CMD_TBS_PER_TFD];
281	u8 id;
282};
283
284static inline void iwl_free_resp(struct iwl_host_cmd *cmd)
285{
286	free_pages(cmd->_rx_page_addr, cmd->_rx_page_order);
287}
288
289struct iwl_rx_cmd_buffer {
290	struct page *_page;
291	int _offset;
292	bool _page_stolen;
293	u32 _rx_page_order;
294	unsigned int truesize;
295};
296
297static inline void *rxb_addr(struct iwl_rx_cmd_buffer *r)
298{
299	return (void *)((unsigned long)page_address(r->_page) + r->_offset);
300}
301
302static inline int rxb_offset(struct iwl_rx_cmd_buffer *r)
303{
304	return r->_offset;
305}
306
307static inline struct page *rxb_steal_page(struct iwl_rx_cmd_buffer *r)
308{
309	r->_page_stolen = true;
310	get_page(r->_page);
311	return r->_page;
312}
313
314static inline void iwl_free_rxb(struct iwl_rx_cmd_buffer *r)
315{
316	__free_pages(r->_page, r->_rx_page_order);
317}
318
319#define MAX_NO_RECLAIM_CMDS	6
320
321#define IWL_MASK(lo, hi) ((1 << (hi)) | ((1 << (hi)) - (1 << (lo))))
322
323/*
324 * Maximum number of HW queues the transport layer
325 * currently supports
326 */
327#define IWL_MAX_HW_QUEUES		32
328#define IWL_MAX_TID_COUNT	8
329#define IWL_FRAME_LIMIT	64
330
331/**
332 * enum iwl_wowlan_status - WoWLAN image/device status
333 * @IWL_D3_STATUS_ALIVE: firmware is still running after resume
334 * @IWL_D3_STATUS_RESET: device was reset while suspended
335 */
336enum iwl_d3_status {
337	IWL_D3_STATUS_ALIVE,
338	IWL_D3_STATUS_RESET,
339};
340
341/**
342 * enum iwl_trans_status: transport status flags
343 * @STATUS_SYNC_HCMD_ACTIVE: a SYNC command is being processed
344 * @STATUS_DEVICE_ENABLED: APM is enabled
345 * @STATUS_TPOWER_PMI: the device might be asleep (need to wake it up)
346 * @STATUS_INT_ENABLED: interrupts are enabled
347 * @STATUS_RFKILL: the HW RFkill switch is in KILL position
348 * @STATUS_FW_ERROR: the fw is in error state
349 * @STATUS_TRANS_GOING_IDLE: shutting down the trans, only special commands
350 *	are sent
351 * @STATUS_TRANS_IDLE: the trans is idle - general commands are not to be sent
352 */
353enum iwl_trans_status {
354	STATUS_SYNC_HCMD_ACTIVE,
355	STATUS_DEVICE_ENABLED,
356	STATUS_TPOWER_PMI,
357	STATUS_INT_ENABLED,
358	STATUS_RFKILL,
359	STATUS_FW_ERROR,
360	STATUS_TRANS_GOING_IDLE,
361	STATUS_TRANS_IDLE,
362};
363
364/**
365 * struct iwl_trans_config - transport configuration
366 *
367 * @op_mode: pointer to the upper layer.
368 * @cmd_queue: the index of the command queue.
369 *	Must be set before start_fw.
370 * @cmd_fifo: the fifo for host commands
371 * @cmd_q_wdg_timeout: the timeout of the watchdog timer for the command queue.
372 * @no_reclaim_cmds: Some devices erroneously don't set the
373 *	SEQ_RX_FRAME bit on some notifications, this is the
374 *	list of such notifications to filter. Max length is
375 *	%MAX_NO_RECLAIM_CMDS.
376 * @n_no_reclaim_cmds: # of commands in list
377 * @rx_buf_size_8k: 8 kB RX buffer size needed for A-MSDUs,
378 *	if unset 4k will be the RX buffer size
379 * @bc_table_dword: set to true if the BC table expects the byte count to be
380 *	in DWORD (as opposed to bytes)
381 * @scd_set_active: should the transport configure the SCD for HCMD queue
382 * @command_names: array of command names, must be 256 entries
383 *	(one for each command); for debugging only
384 * @sdio_adma_addr: the default address to set for the ADMA in SDIO mode until
385 *	we get the ALIVE from the uCode
386 */
387struct iwl_trans_config {
388	struct iwl_op_mode *op_mode;
389
390	u8 cmd_queue;
391	u8 cmd_fifo;
392	unsigned int cmd_q_wdg_timeout;
393	const u8 *no_reclaim_cmds;
394	unsigned int n_no_reclaim_cmds;
395
396	bool rx_buf_size_8k;
397	bool bc_table_dword;
398	bool scd_set_active;
399	const char *const *command_names;
400
401	u32 sdio_adma_addr;
402};
403
404struct iwl_trans_dump_data {
405	u32 len;
406	u8 data[];
407};
408
409struct iwl_trans;
410
411struct iwl_trans_txq_scd_cfg {
412	u8 fifo;
413	s8 sta_id;
414	u8 tid;
415	bool aggregate;
416	int frame_limit;
417};
418
419/**
420 * struct iwl_trans_ops - transport specific operations
421 *
422 * All the handlers MUST be implemented
423 *
424 * @start_hw: starts the HW. If low_power is true, the NIC needs to be taken
425 *	out of a low power state. From that point on, the HW can send
426 *	interrupts. May sleep.
427 * @op_mode_leave: Turn off the HW RF kill indication if on
428 *	May sleep
429 * @start_fw: allocates and inits all the resources for the transport
430 *	layer. Also kick a fw image.
431 *	May sleep
432 * @fw_alive: called when the fw sends alive notification. If the fw provides
433 *	the SCD base address in SRAM, then provide it here, or 0 otherwise.
434 *	May sleep
435 * @stop_device: stops the whole device (embedded CPU put to reset) and stops
436 *	the HW. If low_power is true, the NIC will be put in low power state.
437 *	From that point on, the HW will be stopped but will still issue an
438 *	interrupt if the HW RF kill switch is triggered.
439 *	This callback must do the right thing and not crash even if %start_hw()
440 *	was called but not &start_fw(). May sleep.
441 * @d3_suspend: put the device into the correct mode for WoWLAN during
442 *	suspend. This is optional, if not implemented WoWLAN will not be
443 *	supported. This callback may sleep.
444 * @d3_resume: resume the device after WoWLAN, enabling the opmode to
445 *	talk to the WoWLAN image to get its status. This is optional, if not
446 *	implemented WoWLAN will not be supported. This callback may sleep.
447 * @send_cmd:send a host command. Must return -ERFKILL if RFkill is asserted.
448 *	If RFkill is asserted in the middle of a SYNC host command, it must
449 *	return -ERFKILL straight away.
450 *	May sleep only if CMD_ASYNC is not set
451 * @tx: send an skb
452 *	Must be atomic
453 * @reclaim: free packet until ssn. Returns a list of freed packets.
454 *	Must be atomic
455 * @txq_enable: setup a queue. To setup an AC queue, use the
456 *	iwl_trans_ac_txq_enable wrapper. fw_alive must have been called before
457 *	this one. The op_mode must not configure the HCMD queue. The scheduler
458 *	configuration may be %NULL, in which case the hardware will not be
459 *	configured. May sleep.
460 * @txq_disable: de-configure a Tx queue to send AMPDUs
461 *	Must be atomic
462 * @wait_tx_queue_empty: wait until tx queues are empty. May sleep.
463 * @freeze_txq_timer: prevents the timer of the queue from firing until the
464 *	queue is set to awake. Must be atomic.
465 * @dbgfs_register: add the dbgfs files under this directory. Files will be
466 *	automatically deleted.
467 * @write8: write a u8 to a register at offset ofs from the BAR
468 * @write32: write a u32 to a register at offset ofs from the BAR
469 * @read32: read a u32 register at offset ofs from the BAR
470 * @read_prph: read a DWORD from a periphery register
471 * @write_prph: write a DWORD to a periphery register
472 * @read_mem: read device's SRAM in DWORD
473 * @write_mem: write device's SRAM in DWORD. If %buf is %NULL, then the memory
474 *	will be zeroed.
475 * @configure: configure parameters required by the transport layer from
476 *	the op_mode. May be called several times before start_fw, can't be
477 *	called after that.
478 * @set_pmi: set the power pmi state
479 * @grab_nic_access: wake the NIC to be able to access non-HBUS regs.
480 *	Sleeping is not allowed between grab_nic_access and
481 *	release_nic_access.
482 * @release_nic_access: let the NIC go to sleep. The "flags" parameter
483 *	must be the same one that was sent before to the grab_nic_access.
484 * @set_bits_mask - set SRAM register according to value and mask.
485 * @ref: grab a reference to the transport/FW layers, disallowing
486 *	certain low power states
487 * @unref: release a reference previously taken with @ref. Note that
488 *	initially the reference count is 1, making an initial @unref
489 *	necessary to allow low power states.
490 * @dump_data: return a vmalloc'ed buffer with debug data, maybe containing last
491 *	TX'ed commands and similar. The buffer will be vfree'd by the caller.
492 *	Note that the transport must fill in the proper file headers.
493 */
494struct iwl_trans_ops {
495
496	int (*start_hw)(struct iwl_trans *iwl_trans, bool low_power);
497	void (*op_mode_leave)(struct iwl_trans *iwl_trans);
498	int (*start_fw)(struct iwl_trans *trans, const struct fw_img *fw,
499			bool run_in_rfkill);
500	int (*update_sf)(struct iwl_trans *trans,
501			 struct iwl_sf_region *st_fwrd_space);
502	void (*fw_alive)(struct iwl_trans *trans, u32 scd_addr);
503	void (*stop_device)(struct iwl_trans *trans, bool low_power);
504
505	void (*d3_suspend)(struct iwl_trans *trans, bool test);
506	int (*d3_resume)(struct iwl_trans *trans, enum iwl_d3_status *status,
507			 bool test);
508
509	int (*send_cmd)(struct iwl_trans *trans, struct iwl_host_cmd *cmd);
510
511	int (*tx)(struct iwl_trans *trans, struct sk_buff *skb,
512		  struct iwl_device_cmd *dev_cmd, int queue);
513	void (*reclaim)(struct iwl_trans *trans, int queue, int ssn,
514			struct sk_buff_head *skbs);
515
516	void (*txq_enable)(struct iwl_trans *trans, int queue, u16 ssn,
517			   const struct iwl_trans_txq_scd_cfg *cfg,
518			   unsigned int queue_wdg_timeout);
519	void (*txq_disable)(struct iwl_trans *trans, int queue,
520			    bool configure_scd);
521
522	int (*dbgfs_register)(struct iwl_trans *trans, struct dentry* dir);
523	int (*wait_tx_queue_empty)(struct iwl_trans *trans, u32 txq_bm);
524	void (*freeze_txq_timer)(struct iwl_trans *trans, unsigned long txqs,
525				 bool freeze);
526
527	void (*write8)(struct iwl_trans *trans, u32 ofs, u8 val);
528	void (*write32)(struct iwl_trans *trans, u32 ofs, u32 val);
529	u32 (*read32)(struct iwl_trans *trans, u32 ofs);
530	u32 (*read_prph)(struct iwl_trans *trans, u32 ofs);
531	void (*write_prph)(struct iwl_trans *trans, u32 ofs, u32 val);
532	int (*read_mem)(struct iwl_trans *trans, u32 addr,
533			void *buf, int dwords);
534	int (*write_mem)(struct iwl_trans *trans, u32 addr,
535			 const void *buf, int dwords);
536	void (*configure)(struct iwl_trans *trans,
537			  const struct iwl_trans_config *trans_cfg);
538	void (*set_pmi)(struct iwl_trans *trans, bool state);
539	bool (*grab_nic_access)(struct iwl_trans *trans, bool silent,
540				unsigned long *flags);
541	void (*release_nic_access)(struct iwl_trans *trans,
542				   unsigned long *flags);
543	void (*set_bits_mask)(struct iwl_trans *trans, u32 reg, u32 mask,
544			      u32 value);
545	void (*ref)(struct iwl_trans *trans);
546	void (*unref)(struct iwl_trans *trans);
547	void (*suspend)(struct iwl_trans *trans);
548	void (*resume)(struct iwl_trans *trans);
549
550	struct iwl_trans_dump_data *(*dump_data)(struct iwl_trans *trans);
551};
552
553/**
554 * enum iwl_trans_state - state of the transport layer
555 *
556 * @IWL_TRANS_NO_FW: no fw has sent an alive response
557 * @IWL_TRANS_FW_ALIVE: a fw has sent an alive response
558 */
559enum iwl_trans_state {
560	IWL_TRANS_NO_FW = 0,
561	IWL_TRANS_FW_ALIVE	= 1,
562};
563
564/**
565 * enum iwl_d0i3_mode - d0i3 mode
566 *
567 * @IWL_D0I3_MODE_OFF - d0i3 is disabled
568 * @IWL_D0I3_MODE_ON_IDLE - enter d0i3 when device is idle
569 *	(e.g. no active references)
570 * @IWL_D0I3_MODE_ON_SUSPEND - enter d0i3 only on suspend
571 *	(in case of 'any' trigger)
572 */
573enum iwl_d0i3_mode {
574	IWL_D0I3_MODE_OFF = 0,
575	IWL_D0I3_MODE_ON_IDLE,
576	IWL_D0I3_MODE_ON_SUSPEND,
577};
578
579/**
580 * struct iwl_trans - transport common data
581 *
582 * @ops - pointer to iwl_trans_ops
583 * @op_mode - pointer to the op_mode
584 * @cfg - pointer to the configuration
585 * @status: a bit-mask of transport status flags
586 * @dev - pointer to struct device * that represents the device
587 * @hw_id: a u32 with the ID of the device / sub-device.
588 *	Set during transport allocation.
589 * @hw_id_str: a string with info about HW ID. Set during transport allocation.
590 * @pm_support: set to true in start_hw if link pm is supported
591 * @ltr_enabled: set to true if the LTR is enabled
592 * @dev_cmd_pool: pool for Tx cmd allocation - for internal use only.
593 *	The user should use iwl_trans_{alloc,free}_tx_cmd.
594 * @dev_cmd_headroom: room needed for the transport's private use before the
595 *	device_cmd for Tx - for internal use only
596 *	The user should use iwl_trans_{alloc,free}_tx_cmd.
597 * @rx_mpdu_cmd: MPDU RX command ID, must be assigned by opmode before
598 *	starting the firmware, used for tracing
599 * @rx_mpdu_cmd_hdr_size: used for tracing, amount of data before the
600 *	start of the 802.11 header in the @rx_mpdu_cmd
601 * @dflt_pwr_limit: default power limit fetched from the platform (ACPI)
602 * @dbg_dest_tlv: points to the destination TLV for debug
603 * @dbg_conf_tlv: array of pointers to configuration TLVs for debug
604 * @dbg_trigger_tlv: array of pointers to triggers TLVs for debug
605 * @dbg_dest_reg_num: num of reg_ops in %dbg_dest_tlv
606 */
607struct iwl_trans {
608	const struct iwl_trans_ops *ops;
609	struct iwl_op_mode *op_mode;
610	const struct iwl_cfg *cfg;
611	enum iwl_trans_state state;
612	unsigned long status;
613
614	struct device *dev;
615	u32 hw_rev;
616	u32 hw_id;
617	char hw_id_str[52];
618
619	u8 rx_mpdu_cmd, rx_mpdu_cmd_hdr_size;
620
621	bool pm_support;
622	bool ltr_enabled;
623
624	/* The following fields are internal only */
625	struct kmem_cache *dev_cmd_pool;
626	size_t dev_cmd_headroom;
627	char dev_cmd_pool_name[50];
628
629	struct dentry *dbgfs_dir;
630
631#ifdef CONFIG_LOCKDEP
632	struct lockdep_map sync_cmd_lockdep_map;
633#endif
634
635	u64 dflt_pwr_limit;
636
637	const struct iwl_fw_dbg_dest_tlv *dbg_dest_tlv;
638	const struct iwl_fw_dbg_conf_tlv *dbg_conf_tlv[FW_DBG_CONF_MAX];
639	struct iwl_fw_dbg_trigger_tlv * const *dbg_trigger_tlv;
640	u8 dbg_dest_reg_num;
641
642	enum iwl_d0i3_mode d0i3_mode;
643
644	/* pointer to trans specific struct */
645	/*Ensure that this pointer will always be aligned to sizeof pointer */
646	char trans_specific[0] __aligned(sizeof(void *));
647};
648
649static inline void iwl_trans_configure(struct iwl_trans *trans,
650				       const struct iwl_trans_config *trans_cfg)
651{
652	trans->op_mode = trans_cfg->op_mode;
653
654	trans->ops->configure(trans, trans_cfg);
655}
656
657static inline int _iwl_trans_start_hw(struct iwl_trans *trans, bool low_power)
658{
659	might_sleep();
660
661	return trans->ops->start_hw(trans, low_power);
662}
663
664static inline int iwl_trans_start_hw(struct iwl_trans *trans)
665{
666	return trans->ops->start_hw(trans, true);
667}
668
669static inline void iwl_trans_op_mode_leave(struct iwl_trans *trans)
670{
671	might_sleep();
672
673	if (trans->ops->op_mode_leave)
674		trans->ops->op_mode_leave(trans);
675
676	trans->op_mode = NULL;
677
678	trans->state = IWL_TRANS_NO_FW;
679}
680
681static inline void iwl_trans_fw_alive(struct iwl_trans *trans, u32 scd_addr)
682{
683	might_sleep();
684
685	trans->state = IWL_TRANS_FW_ALIVE;
686
687	trans->ops->fw_alive(trans, scd_addr);
688}
689
690static inline int iwl_trans_start_fw(struct iwl_trans *trans,
691				     const struct fw_img *fw,
692				     bool run_in_rfkill)
693{
694	might_sleep();
695
696	WARN_ON_ONCE(!trans->rx_mpdu_cmd);
697
698	clear_bit(STATUS_FW_ERROR, &trans->status);
699	return trans->ops->start_fw(trans, fw, run_in_rfkill);
700}
701
702static inline int iwl_trans_update_sf(struct iwl_trans *trans,
703				      struct iwl_sf_region *st_fwrd_space)
704{
705	might_sleep();
706
707	if (trans->ops->update_sf)
708		return trans->ops->update_sf(trans, st_fwrd_space);
709
710	return 0;
711}
712
713static inline void _iwl_trans_stop_device(struct iwl_trans *trans,
714					  bool low_power)
715{
716	might_sleep();
717
718	trans->ops->stop_device(trans, low_power);
719
720	trans->state = IWL_TRANS_NO_FW;
721}
722
723static inline void iwl_trans_stop_device(struct iwl_trans *trans)
724{
725	_iwl_trans_stop_device(trans, true);
726}
727
728static inline void iwl_trans_d3_suspend(struct iwl_trans *trans, bool test)
729{
730	might_sleep();
731	trans->ops->d3_suspend(trans, test);
732}
733
734static inline int iwl_trans_d3_resume(struct iwl_trans *trans,
735				      enum iwl_d3_status *status,
736				      bool test)
737{
738	might_sleep();
739	return trans->ops->d3_resume(trans, status, test);
740}
741
742static inline void iwl_trans_ref(struct iwl_trans *trans)
743{
744	if (trans->ops->ref)
745		trans->ops->ref(trans);
746}
747
748static inline void iwl_trans_unref(struct iwl_trans *trans)
749{
750	if (trans->ops->unref)
751		trans->ops->unref(trans);
752}
753
754static inline void iwl_trans_suspend(struct iwl_trans *trans)
755{
756	if (trans->ops->suspend)
757		trans->ops->suspend(trans);
758}
759
760static inline void iwl_trans_resume(struct iwl_trans *trans)
761{
762	if (trans->ops->resume)
763		trans->ops->resume(trans);
764}
765
766static inline struct iwl_trans_dump_data *
767iwl_trans_dump_data(struct iwl_trans *trans)
768{
769	if (!trans->ops->dump_data)
770		return NULL;
771	return trans->ops->dump_data(trans);
772}
773
774static inline int iwl_trans_send_cmd(struct iwl_trans *trans,
775				     struct iwl_host_cmd *cmd)
776{
777	int ret;
778
779	if (unlikely(!(cmd->flags & CMD_SEND_IN_RFKILL) &&
780		     test_bit(STATUS_RFKILL, &trans->status)))
781		return -ERFKILL;
782
783	if (unlikely(test_bit(STATUS_FW_ERROR, &trans->status)))
784		return -EIO;
785
786	if (unlikely(trans->state != IWL_TRANS_FW_ALIVE)) {
787		IWL_ERR(trans, "%s bad state = %d\n", __func__, trans->state);
788		return -EIO;
789	}
790
791	if (!(cmd->flags & CMD_ASYNC))
792		lock_map_acquire_read(&trans->sync_cmd_lockdep_map);
793
794	ret = trans->ops->send_cmd(trans, cmd);
795
796	if (!(cmd->flags & CMD_ASYNC))
797		lock_map_release(&trans->sync_cmd_lockdep_map);
798
799	return ret;
800}
801
802static inline struct iwl_device_cmd *
803iwl_trans_alloc_tx_cmd(struct iwl_trans *trans)
804{
805	u8 *dev_cmd_ptr = kmem_cache_alloc(trans->dev_cmd_pool, GFP_ATOMIC);
806
807	if (unlikely(dev_cmd_ptr == NULL))
808		return NULL;
809
810	return (struct iwl_device_cmd *)
811			(dev_cmd_ptr + trans->dev_cmd_headroom);
812}
813
814static inline void iwl_trans_free_tx_cmd(struct iwl_trans *trans,
815					 struct iwl_device_cmd *dev_cmd)
816{
817	u8 *dev_cmd_ptr = (u8 *)dev_cmd - trans->dev_cmd_headroom;
818
819	kmem_cache_free(trans->dev_cmd_pool, dev_cmd_ptr);
820}
821
822static inline int iwl_trans_tx(struct iwl_trans *trans, struct sk_buff *skb,
823			       struct iwl_device_cmd *dev_cmd, int queue)
824{
825	if (unlikely(test_bit(STATUS_FW_ERROR, &trans->status)))
826		return -EIO;
827
828	if (unlikely(trans->state != IWL_TRANS_FW_ALIVE))
829		IWL_ERR(trans, "%s bad state = %d\n", __func__, trans->state);
830
831	return trans->ops->tx(trans, skb, dev_cmd, queue);
832}
833
834static inline void iwl_trans_reclaim(struct iwl_trans *trans, int queue,
835				     int ssn, struct sk_buff_head *skbs)
836{
837	if (unlikely(trans->state != IWL_TRANS_FW_ALIVE))
838		IWL_ERR(trans, "%s bad state = %d\n", __func__, trans->state);
839
840	trans->ops->reclaim(trans, queue, ssn, skbs);
841}
842
843static inline void iwl_trans_txq_disable(struct iwl_trans *trans, int queue,
844					 bool configure_scd)
845{
846	trans->ops->txq_disable(trans, queue, configure_scd);
847}
848
849static inline void
850iwl_trans_txq_enable_cfg(struct iwl_trans *trans, int queue, u16 ssn,
851			 const struct iwl_trans_txq_scd_cfg *cfg,
852			 unsigned int queue_wdg_timeout)
853{
854	might_sleep();
855
856	if (unlikely((trans->state != IWL_TRANS_FW_ALIVE)))
857		IWL_ERR(trans, "%s bad state = %d\n", __func__, trans->state);
858
859	trans->ops->txq_enable(trans, queue, ssn, cfg, queue_wdg_timeout);
860}
861
862static inline void iwl_trans_txq_enable(struct iwl_trans *trans, int queue,
863					int fifo, int sta_id, int tid,
864					int frame_limit, u16 ssn,
865					unsigned int queue_wdg_timeout)
866{
867	struct iwl_trans_txq_scd_cfg cfg = {
868		.fifo = fifo,
869		.sta_id = sta_id,
870		.tid = tid,
871		.frame_limit = frame_limit,
872		.aggregate = sta_id >= 0,
873	};
874
875	iwl_trans_txq_enable_cfg(trans, queue, ssn, &cfg, queue_wdg_timeout);
876}
877
878static inline
879void iwl_trans_ac_txq_enable(struct iwl_trans *trans, int queue, int fifo,
880			     unsigned int queue_wdg_timeout)
881{
882	struct iwl_trans_txq_scd_cfg cfg = {
883		.fifo = fifo,
884		.sta_id = -1,
885		.tid = IWL_MAX_TID_COUNT,
886		.frame_limit = IWL_FRAME_LIMIT,
887		.aggregate = false,
888	};
889
890	iwl_trans_txq_enable_cfg(trans, queue, 0, &cfg, queue_wdg_timeout);
891}
892
893static inline void iwl_trans_freeze_txq_timer(struct iwl_trans *trans,
894					      unsigned long txqs,
895					      bool freeze)
896{
897	if (unlikely(trans->state != IWL_TRANS_FW_ALIVE))
898		IWL_ERR(trans, "%s bad state = %d\n", __func__, trans->state);
899
900	if (trans->ops->freeze_txq_timer)
901		trans->ops->freeze_txq_timer(trans, txqs, freeze);
902}
903
904static inline int iwl_trans_wait_tx_queue_empty(struct iwl_trans *trans,
905						u32 txqs)
906{
907	if (unlikely(trans->state != IWL_TRANS_FW_ALIVE))
908		IWL_ERR(trans, "%s bad state = %d\n", __func__, trans->state);
909
910	return trans->ops->wait_tx_queue_empty(trans, txqs);
911}
912
913static inline int iwl_trans_dbgfs_register(struct iwl_trans *trans,
914					   struct dentry *dir)
915{
916	return trans->ops->dbgfs_register(trans, dir);
917}
918
919static inline void iwl_trans_write8(struct iwl_trans *trans, u32 ofs, u8 val)
920{
921	trans->ops->write8(trans, ofs, val);
922}
923
924static inline void iwl_trans_write32(struct iwl_trans *trans, u32 ofs, u32 val)
925{
926	trans->ops->write32(trans, ofs, val);
927}
928
929static inline u32 iwl_trans_read32(struct iwl_trans *trans, u32 ofs)
930{
931	return trans->ops->read32(trans, ofs);
932}
933
934static inline u32 iwl_trans_read_prph(struct iwl_trans *trans, u32 ofs)
935{
936	return trans->ops->read_prph(trans, ofs);
937}
938
939static inline void iwl_trans_write_prph(struct iwl_trans *trans, u32 ofs,
940					u32 val)
941{
942	return trans->ops->write_prph(trans, ofs, val);
943}
944
945static inline int iwl_trans_read_mem(struct iwl_trans *trans, u32 addr,
946				     void *buf, int dwords)
947{
948	return trans->ops->read_mem(trans, addr, buf, dwords);
949}
950
951#define iwl_trans_read_mem_bytes(trans, addr, buf, bufsize)		      \
952	do {								      \
953		if (__builtin_constant_p(bufsize))			      \
954			BUILD_BUG_ON((bufsize) % sizeof(u32));		      \
955		iwl_trans_read_mem(trans, addr, buf, (bufsize) / sizeof(u32));\
956	} while (0)
957
958static inline u32 iwl_trans_read_mem32(struct iwl_trans *trans, u32 addr)
959{
960	u32 value;
961
962	if (WARN_ON(iwl_trans_read_mem(trans, addr, &value, 1)))
963		return 0xa5a5a5a5;
964
965	return value;
966}
967
968static inline int iwl_trans_write_mem(struct iwl_trans *trans, u32 addr,
969				      const void *buf, int dwords)
970{
971	return trans->ops->write_mem(trans, addr, buf, dwords);
972}
973
974static inline u32 iwl_trans_write_mem32(struct iwl_trans *trans, u32 addr,
975					u32 val)
976{
977	return iwl_trans_write_mem(trans, addr, &val, 1);
978}
979
980static inline void iwl_trans_set_pmi(struct iwl_trans *trans, bool state)
981{
982	if (trans->ops->set_pmi)
983		trans->ops->set_pmi(trans, state);
984}
985
986static inline void
987iwl_trans_set_bits_mask(struct iwl_trans *trans, u32 reg, u32 mask, u32 value)
988{
989	trans->ops->set_bits_mask(trans, reg, mask, value);
990}
991
992#define iwl_trans_grab_nic_access(trans, silent, flags)	\
993	__cond_lock(nic_access,				\
994		    likely((trans)->ops->grab_nic_access(trans, silent, flags)))
995
996static inline void __releases(nic_access)
997iwl_trans_release_nic_access(struct iwl_trans *trans, unsigned long *flags)
998{
999	trans->ops->release_nic_access(trans, flags);
1000	__release(nic_access);
1001}
1002
1003static inline void iwl_trans_fw_error(struct iwl_trans *trans)
1004{
1005	if (WARN_ON_ONCE(!trans->op_mode))
1006		return;
1007
1008	/* prevent double restarts due to the same erroneous FW */
1009	if (!test_and_set_bit(STATUS_FW_ERROR, &trans->status))
1010		iwl_op_mode_nic_error(trans->op_mode);
1011}
1012
1013/*****************************************************
1014* driver (transport) register/unregister functions
1015******************************************************/
1016int __must_check iwl_pci_register_driver(void);
1017void iwl_pci_unregister_driver(void);
1018
1019static inline void trans_lockdep_init(struct iwl_trans *trans)
1020{
1021#ifdef CONFIG_LOCKDEP
1022	static struct lock_class_key __key;
1023
1024	lockdep_init_map(&trans->sync_cmd_lockdep_map, "sync_cmd_lockdep_map",
1025			 &__key, 0);
1026#endif
1027}
1028
1029#endif /* __iwl_trans_h__ */
1030