1/* 2 * Xilinx USB peripheral controller driver 3 * 4 * Copyright (C) 2004 by Thomas Rathbone 5 * Copyright (C) 2005 by HP Labs 6 * Copyright (C) 2005 by David Brownell 7 * Copyright (C) 2010 - 2014 Xilinx, Inc. 8 * 9 * Some parts of this driver code is based on the driver for at91-series 10 * USB peripheral controller (at91_udc.c). 11 * 12 * This program is free software; you can redistribute it 13 * and/or modify it under the terms of the GNU General Public 14 * License as published by the Free Software Foundation; 15 * either version 2 of the License, or (at your option) any 16 * later version. 17 */ 18 19#include <linux/delay.h> 20#include <linux/device.h> 21#include <linux/dma-mapping.h> 22#include <linux/interrupt.h> 23#include <linux/io.h> 24#include <linux/module.h> 25#include <linux/of_address.h> 26#include <linux/of_device.h> 27#include <linux/of_platform.h> 28#include <linux/of_irq.h> 29#include <linux/prefetch.h> 30#include <linux/usb/ch9.h> 31#include <linux/usb/gadget.h> 32 33/* Register offsets for the USB device.*/ 34#define XUSB_EP0_CONFIG_OFFSET 0x0000 /* EP0 Config Reg Offset */ 35#define XUSB_SETUP_PKT_ADDR_OFFSET 0x0080 /* Setup Packet Address */ 36#define XUSB_ADDRESS_OFFSET 0x0100 /* Address Register */ 37#define XUSB_CONTROL_OFFSET 0x0104 /* Control Register */ 38#define XUSB_STATUS_OFFSET 0x0108 /* Status Register */ 39#define XUSB_FRAMENUM_OFFSET 0x010C /* Frame Number Register */ 40#define XUSB_IER_OFFSET 0x0110 /* Interrupt Enable Register */ 41#define XUSB_BUFFREADY_OFFSET 0x0114 /* Buffer Ready Register */ 42#define XUSB_TESTMODE_OFFSET 0x0118 /* Test Mode Register */ 43#define XUSB_DMA_RESET_OFFSET 0x0200 /* DMA Soft Reset Register */ 44#define XUSB_DMA_CONTROL_OFFSET 0x0204 /* DMA Control Register */ 45#define XUSB_DMA_DSAR_ADDR_OFFSET 0x0208 /* DMA source Address Reg */ 46#define XUSB_DMA_DDAR_ADDR_OFFSET 0x020C /* DMA destination Addr Reg */ 47#define XUSB_DMA_LENGTH_OFFSET 0x0210 /* DMA Length Register */ 48#define XUSB_DMA_STATUS_OFFSET 0x0214 /* DMA Status Register */ 49 50/* Endpoint Configuration Space offsets */ 51#define XUSB_EP_CFGSTATUS_OFFSET 0x00 /* Endpoint Config Status */ 52#define XUSB_EP_BUF0COUNT_OFFSET 0x08 /* Buffer 0 Count */ 53#define XUSB_EP_BUF1COUNT_OFFSET 0x0C /* Buffer 1 Count */ 54 55#define XUSB_CONTROL_USB_READY_MASK 0x80000000 /* USB ready Mask */ 56#define XUSB_CONTROL_USB_RMTWAKE_MASK 0x40000000 /* Remote wake up mask */ 57 58/* Interrupt register related masks.*/ 59#define XUSB_STATUS_GLOBAL_INTR_MASK 0x80000000 /* Global Intr Enable */ 60#define XUSB_STATUS_DMADONE_MASK 0x04000000 /* DMA done Mask */ 61#define XUSB_STATUS_DMAERR_MASK 0x02000000 /* DMA Error Mask */ 62#define XUSB_STATUS_DMABUSY_MASK 0x80000000 /* DMA Error Mask */ 63#define XUSB_STATUS_RESUME_MASK 0x01000000 /* USB Resume Mask */ 64#define XUSB_STATUS_RESET_MASK 0x00800000 /* USB Reset Mask */ 65#define XUSB_STATUS_SUSPEND_MASK 0x00400000 /* USB Suspend Mask */ 66#define XUSB_STATUS_DISCONNECT_MASK 0x00200000 /* USB Disconnect Mask */ 67#define XUSB_STATUS_FIFO_BUFF_RDY_MASK 0x00100000 /* FIFO Buff Ready Mask */ 68#define XUSB_STATUS_FIFO_BUFF_FREE_MASK 0x00080000 /* FIFO Buff Free Mask */ 69#define XUSB_STATUS_SETUP_PACKET_MASK 0x00040000 /* Setup packet received */ 70#define XUSB_STATUS_EP1_BUFF2_COMP_MASK 0x00000200 /* EP 1 Buff 2 Processed */ 71#define XUSB_STATUS_EP1_BUFF1_COMP_MASK 0x00000002 /* EP 1 Buff 1 Processed */ 72#define XUSB_STATUS_EP0_BUFF2_COMP_MASK 0x00000100 /* EP 0 Buff 2 Processed */ 73#define XUSB_STATUS_EP0_BUFF1_COMP_MASK 0x00000001 /* EP 0 Buff 1 Processed */ 74#define XUSB_STATUS_HIGH_SPEED_MASK 0x00010000 /* USB Speed Mask */ 75/* Suspend,Reset,Suspend and Disconnect Mask */ 76#define XUSB_STATUS_INTR_EVENT_MASK 0x01E00000 77/* Buffers completion Mask */ 78#define XUSB_STATUS_INTR_BUFF_COMP_ALL_MASK 0x0000FEFF 79/* Mask for buffer 0 and buffer 1 completion for all Endpoints */ 80#define XUSB_STATUS_INTR_BUFF_COMP_SHIFT_MASK 0x00000101 81#define XUSB_STATUS_EP_BUFF2_SHIFT 8 /* EP buffer offset */ 82 83/* Endpoint Configuration Status Register */ 84#define XUSB_EP_CFG_VALID_MASK 0x80000000 /* Endpoint Valid bit */ 85#define XUSB_EP_CFG_STALL_MASK 0x40000000 /* Endpoint Stall bit */ 86#define XUSB_EP_CFG_DATA_TOGGLE_MASK 0x08000000 /* Endpoint Data toggle */ 87 88/* USB device specific global configuration constants.*/ 89#define XUSB_MAX_ENDPOINTS 8 /* Maximum End Points */ 90#define XUSB_EP_NUMBER_ZERO 0 /* End point Zero */ 91/* DPRAM is the source address for DMA transfer */ 92#define XUSB_DMA_READ_FROM_DPRAM 0x80000000 93#define XUSB_DMA_DMASR_BUSY 0x80000000 /* DMA busy */ 94#define XUSB_DMA_DMASR_ERROR 0x40000000 /* DMA Error */ 95/* 96 * When this bit is set, the DMA buffer ready bit is set by hardware upon 97 * DMA transfer completion. 98 */ 99#define XUSB_DMA_BRR_CTRL 0x40000000 /* DMA bufready ctrl bit */ 100/* Phase States */ 101#define SETUP_PHASE 0x0000 /* Setup Phase */ 102#define DATA_PHASE 0x0001 /* Data Phase */ 103#define STATUS_PHASE 0x0002 /* Status Phase */ 104 105#define EP0_MAX_PACKET 64 /* Endpoint 0 maximum packet length */ 106#define STATUSBUFF_SIZE 2 /* Buffer size for GET_STATUS command */ 107#define EPNAME_SIZE 4 /* Buffer size for endpoint name */ 108 109/* container_of helper macros */ 110#define to_udc(g) container_of((g), struct xusb_udc, gadget) 111#define to_xusb_ep(ep) container_of((ep), struct xusb_ep, ep_usb) 112#define to_xusb_req(req) container_of((req), struct xusb_req, usb_req) 113 114/** 115 * struct xusb_req - Xilinx USB device request structure 116 * @usb_req: Linux usb request structure 117 * @queue: usb device request queue 118 * @ep: pointer to xusb_endpoint structure 119 */ 120struct xusb_req { 121 struct usb_request usb_req; 122 struct list_head queue; 123 struct xusb_ep *ep; 124}; 125 126/** 127 * struct xusb_ep - USB end point structure. 128 * @ep_usb: usb endpoint instance 129 * @queue: endpoint message queue 130 * @udc: xilinx usb peripheral driver instance pointer 131 * @desc: pointer to the usb endpoint descriptor 132 * @rambase: the endpoint buffer address 133 * @offset: the endpoint register offset value 134 * @name: name of the endpoint 135 * @epnumber: endpoint number 136 * @maxpacket: maximum packet size the endpoint can store 137 * @buffer0count: the size of the packet recieved in the first buffer 138 * @buffer1count: the size of the packet received in the second buffer 139 * @curbufnum: current buffer of endpoint that will be processed next 140 * @buffer0ready: the busy state of first buffer 141 * @buffer1ready: the busy state of second buffer 142 * @is_in: endpoint direction (IN or OUT) 143 * @is_iso: endpoint type(isochronous or non isochronous) 144 */ 145struct xusb_ep { 146 struct usb_ep ep_usb; 147 struct list_head queue; 148 struct xusb_udc *udc; 149 const struct usb_endpoint_descriptor *desc; 150 u32 rambase; 151 u32 offset; 152 char name[4]; 153 u16 epnumber; 154 u16 maxpacket; 155 u16 buffer0count; 156 u16 buffer1count; 157 u8 curbufnum; 158 bool buffer0ready; 159 bool buffer1ready; 160 bool is_in; 161 bool is_iso; 162}; 163 164/** 165 * struct xusb_udc - USB peripheral driver structure 166 * @gadget: USB gadget driver instance 167 * @ep: an array of endpoint structures 168 * @driver: pointer to the usb gadget driver instance 169 * @setup: usb_ctrlrequest structure for control requests 170 * @req: pointer to dummy request for get status command 171 * @dev: pointer to device structure in gadget 172 * @usb_state: device in suspended state or not 173 * @remote_wkp: remote wakeup enabled by host 174 * @setupseqtx: tx status 175 * @setupseqrx: rx status 176 * @addr: the usb device base address 177 * @lock: instance of spinlock 178 * @dma_enabled: flag indicating whether the dma is included in the system 179 * @read_fn: function pointer to read device registers 180 * @write_fn: function pointer to write to device registers 181 */ 182struct xusb_udc { 183 struct usb_gadget gadget; 184 struct xusb_ep ep[8]; 185 struct usb_gadget_driver *driver; 186 struct usb_ctrlrequest setup; 187 struct xusb_req *req; 188 struct device *dev; 189 u32 usb_state; 190 u32 remote_wkp; 191 u32 setupseqtx; 192 u32 setupseqrx; 193 void __iomem *addr; 194 spinlock_t lock; 195 bool dma_enabled; 196 197 unsigned int (*read_fn)(void __iomem *); 198 void (*write_fn)(void __iomem *, u32, u32); 199}; 200 201/* Endpoint buffer start addresses in the core */ 202static u32 rambase[8] = { 0x22, 0x1000, 0x1100, 0x1200, 0x1300, 0x1400, 0x1500, 203 0x1600 }; 204 205static const char driver_name[] = "xilinx-udc"; 206static const char ep0name[] = "ep0"; 207 208/* Control endpoint configuration.*/ 209static const struct usb_endpoint_descriptor config_bulk_out_desc = { 210 .bLength = USB_DT_ENDPOINT_SIZE, 211 .bDescriptorType = USB_DT_ENDPOINT, 212 .bEndpointAddress = USB_DIR_OUT, 213 .bmAttributes = USB_ENDPOINT_XFER_BULK, 214 .wMaxPacketSize = cpu_to_le16(EP0_MAX_PACKET), 215}; 216 217/** 218 * xudc_write32 - little endian write to device registers 219 * @addr: base addr of device registers 220 * @offset: register offset 221 * @val: data to be written 222 */ 223static void xudc_write32(void __iomem *addr, u32 offset, u32 val) 224{ 225 iowrite32(val, addr + offset); 226} 227 228/** 229 * xudc_read32 - little endian read from device registers 230 * @addr: addr of device register 231 * Return: value at addr 232 */ 233static unsigned int xudc_read32(void __iomem *addr) 234{ 235 return ioread32(addr); 236} 237 238/** 239 * xudc_write32_be - big endian write to device registers 240 * @addr: base addr of device registers 241 * @offset: register offset 242 * @val: data to be written 243 */ 244static void xudc_write32_be(void __iomem *addr, u32 offset, u32 val) 245{ 246 iowrite32be(val, addr + offset); 247} 248 249/** 250 * xudc_read32_be - big endian read from device registers 251 * @addr: addr of device register 252 * Return: value at addr 253 */ 254static unsigned int xudc_read32_be(void __iomem *addr) 255{ 256 return ioread32be(addr); 257} 258 259/** 260 * xudc_wrstatus - Sets up the usb device status stages. 261 * @udc: pointer to the usb device controller structure. 262 */ 263static void xudc_wrstatus(struct xusb_udc *udc) 264{ 265 struct xusb_ep *ep0 = &udc->ep[XUSB_EP_NUMBER_ZERO]; 266 u32 epcfgreg; 267 268 epcfgreg = udc->read_fn(udc->addr + ep0->offset)| 269 XUSB_EP_CFG_DATA_TOGGLE_MASK; 270 udc->write_fn(udc->addr, ep0->offset, epcfgreg); 271 udc->write_fn(udc->addr, ep0->offset + XUSB_EP_BUF0COUNT_OFFSET, 0); 272 udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 1); 273} 274 275/** 276 * xudc_epconfig - Configures the given endpoint. 277 * @ep: pointer to the usb device endpoint structure. 278 * @udc: pointer to the usb peripheral controller structure. 279 * 280 * This function configures a specific endpoint with the given configuration 281 * data. 282 */ 283static void xudc_epconfig(struct xusb_ep *ep, struct xusb_udc *udc) 284{ 285 u32 epcfgreg; 286 287 /* 288 * Configure the end point direction, type, Max Packet Size and the 289 * EP buffer location. 290 */ 291 epcfgreg = ((ep->is_in << 29) | (ep->is_iso << 28) | 292 (ep->ep_usb.maxpacket << 15) | (ep->rambase)); 293 udc->write_fn(udc->addr, ep->offset, epcfgreg); 294 295 /* Set the Buffer count and the Buffer ready bits.*/ 296 udc->write_fn(udc->addr, ep->offset + XUSB_EP_BUF0COUNT_OFFSET, 297 ep->buffer0count); 298 udc->write_fn(udc->addr, ep->offset + XUSB_EP_BUF1COUNT_OFFSET, 299 ep->buffer1count); 300 if (ep->buffer0ready) 301 udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 302 1 << ep->epnumber); 303 if (ep->buffer1ready) 304 udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 305 1 << (ep->epnumber + XUSB_STATUS_EP_BUFF2_SHIFT)); 306} 307 308/** 309 * xudc_start_dma - Starts DMA transfer. 310 * @ep: pointer to the usb device endpoint structure. 311 * @src: DMA source address. 312 * @dst: DMA destination address. 313 * @length: number of bytes to transfer. 314 * 315 * Return: 0 on success, error code on failure 316 * 317 * This function starts DMA transfer by writing to DMA source, 318 * destination and lenth registers. 319 */ 320static int xudc_start_dma(struct xusb_ep *ep, dma_addr_t src, 321 dma_addr_t dst, u32 length) 322{ 323 struct xusb_udc *udc = ep->udc; 324 int rc = 0; 325 u32 timeout = 500; 326 u32 reg; 327 328 /* 329 * Set the addresses in the DMA source and 330 * destination registers and then set the length 331 * into the DMA length register. 332 */ 333 udc->write_fn(udc->addr, XUSB_DMA_DSAR_ADDR_OFFSET, src); 334 udc->write_fn(udc->addr, XUSB_DMA_DDAR_ADDR_OFFSET, dst); 335 udc->write_fn(udc->addr, XUSB_DMA_LENGTH_OFFSET, length); 336 337 /* 338 * Wait till DMA transaction is complete and 339 * check whether the DMA transaction was 340 * successful. 341 */ 342 do { 343 reg = udc->read_fn(udc->addr + XUSB_DMA_STATUS_OFFSET); 344 if (!(reg & XUSB_DMA_DMASR_BUSY)) 345 break; 346 347 /* 348 * We can't sleep here, because it's also called from 349 * interrupt context. 350 */ 351 timeout--; 352 if (!timeout) { 353 dev_err(udc->dev, "DMA timeout\n"); 354 return -ETIMEDOUT; 355 } 356 udelay(1); 357 } while (1); 358 359 if ((udc->read_fn(udc->addr + XUSB_DMA_STATUS_OFFSET) & 360 XUSB_DMA_DMASR_ERROR) == XUSB_DMA_DMASR_ERROR){ 361 dev_err(udc->dev, "DMA Error\n"); 362 rc = -EINVAL; 363 } 364 365 return rc; 366} 367 368/** 369 * xudc_dma_send - Sends IN data using DMA. 370 * @ep: pointer to the usb device endpoint structure. 371 * @req: pointer to the usb request structure. 372 * @buffer: pointer to data to be sent. 373 * @length: number of bytes to send. 374 * 375 * Return: 0 on success, -EAGAIN if no buffer is free and error 376 * code on failure. 377 * 378 * This function sends data using DMA. 379 */ 380static int xudc_dma_send(struct xusb_ep *ep, struct xusb_req *req, 381 u8 *buffer, u32 length) 382{ 383 u32 *eprambase; 384 dma_addr_t src; 385 dma_addr_t dst; 386 struct xusb_udc *udc = ep->udc; 387 388 src = req->usb_req.dma + req->usb_req.actual; 389 if (req->usb_req.length) 390 dma_sync_single_for_device(udc->dev, src, 391 length, DMA_TO_DEVICE); 392 if (!ep->curbufnum && !ep->buffer0ready) { 393 /* Get the Buffer address and copy the transmit data.*/ 394 eprambase = (u32 __force *)(udc->addr + ep->rambase); 395 dst = virt_to_phys(eprambase); 396 udc->write_fn(udc->addr, ep->offset + 397 XUSB_EP_BUF0COUNT_OFFSET, length); 398 udc->write_fn(udc->addr, XUSB_DMA_CONTROL_OFFSET, 399 XUSB_DMA_BRR_CTRL | (1 << ep->epnumber)); 400 ep->buffer0ready = 1; 401 ep->curbufnum = 1; 402 } else if (ep->curbufnum && !ep->buffer1ready) { 403 /* Get the Buffer address and copy the transmit data.*/ 404 eprambase = (u32 __force *)(udc->addr + ep->rambase + 405 ep->ep_usb.maxpacket); 406 dst = virt_to_phys(eprambase); 407 udc->write_fn(udc->addr, ep->offset + 408 XUSB_EP_BUF1COUNT_OFFSET, length); 409 udc->write_fn(udc->addr, XUSB_DMA_CONTROL_OFFSET, 410 XUSB_DMA_BRR_CTRL | (1 << (ep->epnumber + 411 XUSB_STATUS_EP_BUFF2_SHIFT))); 412 ep->buffer1ready = 1; 413 ep->curbufnum = 0; 414 } else { 415 /* None of ping pong buffers are ready currently .*/ 416 return -EAGAIN; 417 } 418 419 return xudc_start_dma(ep, src, dst, length); 420} 421 422/** 423 * xudc_dma_receive - Receives OUT data using DMA. 424 * @ep: pointer to the usb device endpoint structure. 425 * @req: pointer to the usb request structure. 426 * @buffer: pointer to storage buffer of received data. 427 * @length: number of bytes to receive. 428 * 429 * Return: 0 on success, -EAGAIN if no buffer is free and error 430 * code on failure. 431 * 432 * This function receives data using DMA. 433 */ 434static int xudc_dma_receive(struct xusb_ep *ep, struct xusb_req *req, 435 u8 *buffer, u32 length) 436{ 437 u32 *eprambase; 438 dma_addr_t src; 439 dma_addr_t dst; 440 struct xusb_udc *udc = ep->udc; 441 442 dst = req->usb_req.dma + req->usb_req.actual; 443 if (!ep->curbufnum && !ep->buffer0ready) { 444 /* Get the Buffer address and copy the transmit data */ 445 eprambase = (u32 __force *)(udc->addr + ep->rambase); 446 src = virt_to_phys(eprambase); 447 udc->write_fn(udc->addr, XUSB_DMA_CONTROL_OFFSET, 448 XUSB_DMA_BRR_CTRL | XUSB_DMA_READ_FROM_DPRAM | 449 (1 << ep->epnumber)); 450 ep->buffer0ready = 1; 451 ep->curbufnum = 1; 452 } else if (ep->curbufnum && !ep->buffer1ready) { 453 /* Get the Buffer address and copy the transmit data */ 454 eprambase = (u32 __force *)(udc->addr + 455 ep->rambase + ep->ep_usb.maxpacket); 456 src = virt_to_phys(eprambase); 457 udc->write_fn(udc->addr, XUSB_DMA_CONTROL_OFFSET, 458 XUSB_DMA_BRR_CTRL | XUSB_DMA_READ_FROM_DPRAM | 459 (1 << (ep->epnumber + 460 XUSB_STATUS_EP_BUFF2_SHIFT))); 461 ep->buffer1ready = 1; 462 ep->curbufnum = 0; 463 } else { 464 /* None of the ping-pong buffers are ready currently */ 465 return -EAGAIN; 466 } 467 468 return xudc_start_dma(ep, src, dst, length); 469} 470 471/** 472 * xudc_eptxrx - Transmits or receives data to or from an endpoint. 473 * @ep: pointer to the usb endpoint configuration structure. 474 * @req: pointer to the usb request structure. 475 * @bufferptr: pointer to buffer containing the data to be sent. 476 * @bufferlen: The number of data bytes to be sent. 477 * 478 * Return: 0 on success, -EAGAIN if no buffer is free. 479 * 480 * This function copies the transmit/receive data to/from the end point buffer 481 * and enables the buffer for transmission/reception. 482 */ 483static int xudc_eptxrx(struct xusb_ep *ep, struct xusb_req *req, 484 u8 *bufferptr, u32 bufferlen) 485{ 486 u32 *eprambase; 487 u32 bytestosend; 488 int rc = 0; 489 struct xusb_udc *udc = ep->udc; 490 491 bytestosend = bufferlen; 492 if (udc->dma_enabled) { 493 if (ep->is_in) 494 rc = xudc_dma_send(ep, req, bufferptr, bufferlen); 495 else 496 rc = xudc_dma_receive(ep, req, bufferptr, bufferlen); 497 return rc; 498 } 499 /* Put the transmit buffer into the correct ping-pong buffer.*/ 500 if (!ep->curbufnum && !ep->buffer0ready) { 501 /* Get the Buffer address and copy the transmit data.*/ 502 eprambase = (u32 __force *)(udc->addr + ep->rambase); 503 if (ep->is_in) { 504 memcpy(eprambase, bufferptr, bytestosend); 505 udc->write_fn(udc->addr, ep->offset + 506 XUSB_EP_BUF0COUNT_OFFSET, bufferlen); 507 } else { 508 memcpy(bufferptr, eprambase, bytestosend); 509 } 510 /* 511 * Enable the buffer for transmission. 512 */ 513 udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 514 1 << ep->epnumber); 515 ep->buffer0ready = 1; 516 ep->curbufnum = 1; 517 } else if (ep->curbufnum && !ep->buffer1ready) { 518 /* Get the Buffer address and copy the transmit data.*/ 519 eprambase = (u32 __force *)(udc->addr + ep->rambase + 520 ep->ep_usb.maxpacket); 521 if (ep->is_in) { 522 memcpy(eprambase, bufferptr, bytestosend); 523 udc->write_fn(udc->addr, ep->offset + 524 XUSB_EP_BUF1COUNT_OFFSET, bufferlen); 525 } else { 526 memcpy(bufferptr, eprambase, bytestosend); 527 } 528 /* 529 * Enable the buffer for transmission. 530 */ 531 udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 532 1 << (ep->epnumber + XUSB_STATUS_EP_BUFF2_SHIFT)); 533 ep->buffer1ready = 1; 534 ep->curbufnum = 0; 535 } else { 536 /* None of the ping-pong buffers are ready currently */ 537 return -EAGAIN; 538 } 539 return rc; 540} 541 542/** 543 * xudc_done - Exeutes the endpoint data transfer completion tasks. 544 * @ep: pointer to the usb device endpoint structure. 545 * @req: pointer to the usb request structure. 546 * @status: Status of the data transfer. 547 * 548 * Deletes the message from the queue and updates data transfer completion 549 * status. 550 */ 551static void xudc_done(struct xusb_ep *ep, struct xusb_req *req, int status) 552{ 553 struct xusb_udc *udc = ep->udc; 554 555 list_del_init(&req->queue); 556 557 if (req->usb_req.status == -EINPROGRESS) 558 req->usb_req.status = status; 559 else 560 status = req->usb_req.status; 561 562 if (status && status != -ESHUTDOWN) 563 dev_dbg(udc->dev, "%s done %p, status %d\n", 564 ep->ep_usb.name, req, status); 565 /* unmap request if DMA is present*/ 566 if (udc->dma_enabled && ep->epnumber && req->usb_req.length) 567 usb_gadget_unmap_request(&udc->gadget, &req->usb_req, 568 ep->is_in); 569 570 if (req->usb_req.complete) { 571 spin_unlock(&udc->lock); 572 req->usb_req.complete(&ep->ep_usb, &req->usb_req); 573 spin_lock(&udc->lock); 574 } 575} 576 577/** 578 * xudc_read_fifo - Reads the data from the given endpoint buffer. 579 * @ep: pointer to the usb device endpoint structure. 580 * @req: pointer to the usb request structure. 581 * 582 * Return: 0 if request is completed and -EAGAIN if not completed. 583 * 584 * Pulls OUT packet data from the endpoint buffer. 585 */ 586static int xudc_read_fifo(struct xusb_ep *ep, struct xusb_req *req) 587{ 588 u8 *buf; 589 u32 is_short, count, bufferspace; 590 u8 bufoffset; 591 u8 two_pkts = 0; 592 int ret; 593 int retval = -EAGAIN; 594 struct xusb_udc *udc = ep->udc; 595 596 if (ep->buffer0ready && ep->buffer1ready) { 597 dev_dbg(udc->dev, "Packet NOT ready!\n"); 598 return retval; 599 } 600top: 601 if (ep->curbufnum) 602 bufoffset = XUSB_EP_BUF1COUNT_OFFSET; 603 else 604 bufoffset = XUSB_EP_BUF0COUNT_OFFSET; 605 606 count = udc->read_fn(udc->addr + ep->offset + bufoffset); 607 608 if (!ep->buffer0ready && !ep->buffer1ready) 609 two_pkts = 1; 610 611 buf = req->usb_req.buf + req->usb_req.actual; 612 prefetchw(buf); 613 bufferspace = req->usb_req.length - req->usb_req.actual; 614 is_short = count < ep->ep_usb.maxpacket; 615 616 if (unlikely(!bufferspace)) { 617 /* 618 * This happens when the driver's buffer 619 * is smaller than what the host sent. 620 * discard the extra data. 621 */ 622 if (req->usb_req.status != -EOVERFLOW) 623 dev_dbg(udc->dev, "%s overflow %d\n", 624 ep->ep_usb.name, count); 625 req->usb_req.status = -EOVERFLOW; 626 xudc_done(ep, req, -EOVERFLOW); 627 return 0; 628 } 629 630 ret = xudc_eptxrx(ep, req, buf, count); 631 switch (ret) { 632 case 0: 633 req->usb_req.actual += min(count, bufferspace); 634 dev_dbg(udc->dev, "read %s, %d bytes%s req %p %d/%d\n", 635 ep->ep_usb.name, count, is_short ? "/S" : "", req, 636 req->usb_req.actual, req->usb_req.length); 637 bufferspace -= count; 638 /* Completion */ 639 if ((req->usb_req.actual == req->usb_req.length) || is_short) { 640 if (udc->dma_enabled && req->usb_req.length) 641 dma_sync_single_for_cpu(udc->dev, 642 req->usb_req.dma, 643 req->usb_req.actual, 644 DMA_FROM_DEVICE); 645 xudc_done(ep, req, 0); 646 return 0; 647 } 648 if (two_pkts) { 649 two_pkts = 0; 650 goto top; 651 } 652 break; 653 case -EAGAIN: 654 dev_dbg(udc->dev, "receive busy\n"); 655 break; 656 case -EINVAL: 657 case -ETIMEDOUT: 658 /* DMA error, dequeue the request */ 659 xudc_done(ep, req, -ECONNRESET); 660 retval = 0; 661 break; 662 } 663 664 return retval; 665} 666 667/** 668 * xudc_write_fifo - Writes data into the given endpoint buffer. 669 * @ep: pointer to the usb device endpoint structure. 670 * @req: pointer to the usb request structure. 671 * 672 * Return: 0 if request is completed and -EAGAIN if not completed. 673 * 674 * Loads endpoint buffer for an IN packet. 675 */ 676static int xudc_write_fifo(struct xusb_ep *ep, struct xusb_req *req) 677{ 678 u32 max; 679 u32 length; 680 int ret; 681 int retval = -EAGAIN; 682 struct xusb_udc *udc = ep->udc; 683 int is_last, is_short = 0; 684 u8 *buf; 685 686 max = le16_to_cpu(ep->desc->wMaxPacketSize); 687 buf = req->usb_req.buf + req->usb_req.actual; 688 prefetch(buf); 689 length = req->usb_req.length - req->usb_req.actual; 690 length = min(length, max); 691 692 ret = xudc_eptxrx(ep, req, buf, length); 693 switch (ret) { 694 case 0: 695 req->usb_req.actual += length; 696 if (unlikely(length != max)) { 697 is_last = is_short = 1; 698 } else { 699 if (likely(req->usb_req.length != 700 req->usb_req.actual) || req->usb_req.zero) 701 is_last = 0; 702 else 703 is_last = 1; 704 } 705 dev_dbg(udc->dev, "%s: wrote %s %d bytes%s%s %d left %p\n", 706 __func__, ep->ep_usb.name, length, is_last ? "/L" : "", 707 is_short ? "/S" : "", 708 req->usb_req.length - req->usb_req.actual, req); 709 /* completion */ 710 if (is_last) { 711 xudc_done(ep, req, 0); 712 retval = 0; 713 } 714 break; 715 case -EAGAIN: 716 dev_dbg(udc->dev, "Send busy\n"); 717 break; 718 case -EINVAL: 719 case -ETIMEDOUT: 720 /* DMA error, dequeue the request */ 721 xudc_done(ep, req, -ECONNRESET); 722 retval = 0; 723 break; 724 } 725 726 return retval; 727} 728 729/** 730 * xudc_nuke - Cleans up the data transfer message list. 731 * @ep: pointer to the usb device endpoint structure. 732 * @status: Status of the data transfer. 733 */ 734static void xudc_nuke(struct xusb_ep *ep, int status) 735{ 736 struct xusb_req *req; 737 738 while (!list_empty(&ep->queue)) { 739 req = list_first_entry(&ep->queue, struct xusb_req, queue); 740 xudc_done(ep, req, status); 741 } 742} 743 744/** 745 * xudc_ep_set_halt - Stalls/unstalls the given endpoint. 746 * @_ep: pointer to the usb device endpoint structure. 747 * @value: value to indicate stall/unstall. 748 * 749 * Return: 0 for success and error value on failure 750 */ 751static int xudc_ep_set_halt(struct usb_ep *_ep, int value) 752{ 753 struct xusb_ep *ep = to_xusb_ep(_ep); 754 struct xusb_udc *udc; 755 unsigned long flags; 756 u32 epcfgreg; 757 758 if (!_ep || (!ep->desc && ep->epnumber)) { 759 pr_debug("%s: bad ep or descriptor\n", __func__); 760 return -EINVAL; 761 } 762 udc = ep->udc; 763 764 if (ep->is_in && (!list_empty(&ep->queue)) && value) { 765 dev_dbg(udc->dev, "requests pending can't halt\n"); 766 return -EAGAIN; 767 } 768 769 if (ep->buffer0ready || ep->buffer1ready) { 770 dev_dbg(udc->dev, "HW buffers busy can't halt\n"); 771 return -EAGAIN; 772 } 773 774 spin_lock_irqsave(&udc->lock, flags); 775 776 if (value) { 777 /* Stall the device.*/ 778 epcfgreg = udc->read_fn(udc->addr + ep->offset); 779 epcfgreg |= XUSB_EP_CFG_STALL_MASK; 780 udc->write_fn(udc->addr, ep->offset, epcfgreg); 781 } else { 782 /* Unstall the device.*/ 783 epcfgreg = udc->read_fn(udc->addr + ep->offset); 784 epcfgreg &= ~XUSB_EP_CFG_STALL_MASK; 785 udc->write_fn(udc->addr, ep->offset, epcfgreg); 786 if (ep->epnumber) { 787 /* Reset the toggle bit.*/ 788 epcfgreg = udc->read_fn(ep->udc->addr + ep->offset); 789 epcfgreg &= ~XUSB_EP_CFG_DATA_TOGGLE_MASK; 790 udc->write_fn(udc->addr, ep->offset, epcfgreg); 791 } 792 } 793 794 spin_unlock_irqrestore(&udc->lock, flags); 795 return 0; 796} 797 798/** 799 * xudc_ep_enable - Enables the given endpoint. 800 * @ep: pointer to the xusb endpoint structure. 801 * @desc: pointer to usb endpoint descriptor. 802 * 803 * Return: 0 for success and error value on failure 804 */ 805static int __xudc_ep_enable(struct xusb_ep *ep, 806 const struct usb_endpoint_descriptor *desc) 807{ 808 struct xusb_udc *udc = ep->udc; 809 u32 tmp; 810 u32 epcfg; 811 u32 ier; 812 u16 maxpacket; 813 814 ep->is_in = ((desc->bEndpointAddress & USB_DIR_IN) != 0); 815 /* Bit 3...0:endpoint number */ 816 ep->epnumber = (desc->bEndpointAddress & 0x0f); 817 ep->desc = desc; 818 ep->ep_usb.desc = desc; 819 tmp = desc->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK; 820 ep->ep_usb.maxpacket = maxpacket = le16_to_cpu(desc->wMaxPacketSize); 821 822 switch (tmp) { 823 case USB_ENDPOINT_XFER_CONTROL: 824 dev_dbg(udc->dev, "only one control endpoint\n"); 825 /* NON- ISO */ 826 ep->is_iso = 0; 827 return -EINVAL; 828 case USB_ENDPOINT_XFER_INT: 829 /* NON- ISO */ 830 ep->is_iso = 0; 831 if (maxpacket > 64) { 832 dev_dbg(udc->dev, "bogus maxpacket %d\n", maxpacket); 833 return -EINVAL; 834 } 835 break; 836 case USB_ENDPOINT_XFER_BULK: 837 /* NON- ISO */ 838 ep->is_iso = 0; 839 if (!(is_power_of_2(maxpacket) && maxpacket >= 8 && 840 maxpacket <= 512)) { 841 dev_dbg(udc->dev, "bogus maxpacket %d\n", maxpacket); 842 return -EINVAL; 843 } 844 break; 845 case USB_ENDPOINT_XFER_ISOC: 846 /* ISO */ 847 ep->is_iso = 1; 848 break; 849 } 850 851 ep->buffer0ready = 0; 852 ep->buffer1ready = 0; 853 ep->curbufnum = 0; 854 ep->rambase = rambase[ep->epnumber]; 855 xudc_epconfig(ep, udc); 856 857 dev_dbg(udc->dev, "Enable Endpoint %d max pkt is %d\n", 858 ep->epnumber, maxpacket); 859 860 /* Enable the End point.*/ 861 epcfg = udc->read_fn(udc->addr + ep->offset); 862 epcfg |= XUSB_EP_CFG_VALID_MASK; 863 udc->write_fn(udc->addr, ep->offset, epcfg); 864 if (ep->epnumber) 865 ep->rambase <<= 2; 866 867 /* Enable buffer completion interrupts for endpoint */ 868 ier = udc->read_fn(udc->addr + XUSB_IER_OFFSET); 869 ier |= (XUSB_STATUS_INTR_BUFF_COMP_SHIFT_MASK << ep->epnumber); 870 udc->write_fn(udc->addr, XUSB_IER_OFFSET, ier); 871 872 /* for OUT endpoint set buffers ready to receive */ 873 if (ep->epnumber && !ep->is_in) { 874 udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 875 1 << ep->epnumber); 876 ep->buffer0ready = 1; 877 udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 878 (1 << (ep->epnumber + 879 XUSB_STATUS_EP_BUFF2_SHIFT))); 880 ep->buffer1ready = 1; 881 } 882 883 return 0; 884} 885 886/** 887 * xudc_ep_enable - Enables the given endpoint. 888 * @_ep: pointer to the usb endpoint structure. 889 * @desc: pointer to usb endpoint descriptor. 890 * 891 * Return: 0 for success and error value on failure 892 */ 893static int xudc_ep_enable(struct usb_ep *_ep, 894 const struct usb_endpoint_descriptor *desc) 895{ 896 struct xusb_ep *ep; 897 struct xusb_udc *udc; 898 unsigned long flags; 899 int ret; 900 901 if (!_ep || !desc || desc->bDescriptorType != USB_DT_ENDPOINT) { 902 pr_debug("%s: bad ep or descriptor\n", __func__); 903 return -EINVAL; 904 } 905 906 ep = to_xusb_ep(_ep); 907 udc = ep->udc; 908 909 if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) { 910 dev_dbg(udc->dev, "bogus device state\n"); 911 return -ESHUTDOWN; 912 } 913 914 spin_lock_irqsave(&udc->lock, flags); 915 ret = __xudc_ep_enable(ep, desc); 916 spin_unlock_irqrestore(&udc->lock, flags); 917 918 return ret; 919} 920 921/** 922 * xudc_ep_disable - Disables the given endpoint. 923 * @_ep: pointer to the usb endpoint structure. 924 * 925 * Return: 0 for success and error value on failure 926 */ 927static int xudc_ep_disable(struct usb_ep *_ep) 928{ 929 struct xusb_ep *ep; 930 unsigned long flags; 931 u32 epcfg; 932 struct xusb_udc *udc; 933 934 if (!_ep) { 935 pr_debug("%s: invalid ep\n", __func__); 936 return -EINVAL; 937 } 938 939 ep = to_xusb_ep(_ep); 940 udc = ep->udc; 941 942 spin_lock_irqsave(&udc->lock, flags); 943 944 xudc_nuke(ep, -ESHUTDOWN); 945 946 /* Restore the endpoint's pristine config */ 947 ep->desc = NULL; 948 ep->ep_usb.desc = NULL; 949 950 dev_dbg(udc->dev, "USB Ep %d disable\n ", ep->epnumber); 951 /* Disable the endpoint.*/ 952 epcfg = udc->read_fn(udc->addr + ep->offset); 953 epcfg &= ~XUSB_EP_CFG_VALID_MASK; 954 udc->write_fn(udc->addr, ep->offset, epcfg); 955 956 spin_unlock_irqrestore(&udc->lock, flags); 957 return 0; 958} 959 960/** 961 * xudc_ep_alloc_request - Initializes the request queue. 962 * @_ep: pointer to the usb endpoint structure. 963 * @gfp_flags: Flags related to the request call. 964 * 965 * Return: pointer to request structure on success and a NULL on failure. 966 */ 967static struct usb_request *xudc_ep_alloc_request(struct usb_ep *_ep, 968 gfp_t gfp_flags) 969{ 970 struct xusb_ep *ep = to_xusb_ep(_ep); 971 struct xusb_udc *udc; 972 struct xusb_req *req; 973 974 udc = ep->udc; 975 req = kzalloc(sizeof(*req), gfp_flags); 976 if (!req) { 977 dev_err(udc->dev, "%s:not enough memory", __func__); 978 return NULL; 979 } 980 981 req->ep = ep; 982 INIT_LIST_HEAD(&req->queue); 983 return &req->usb_req; 984} 985 986/** 987 * xudc_free_request - Releases the request from queue. 988 * @_ep: pointer to the usb device endpoint structure. 989 * @_req: pointer to the usb request structure. 990 */ 991static void xudc_free_request(struct usb_ep *_ep, struct usb_request *_req) 992{ 993 struct xusb_req *req = to_xusb_req(_req); 994 995 kfree(req); 996} 997 998/** 999 * xudc_ep0_queue - Adds the request to endpoint 0 queue. 1000 * @ep0: pointer to the xusb endpoint 0 structure. 1001 * @req: pointer to the xusb request structure. 1002 * 1003 * Return: 0 for success and error value on failure 1004 */ 1005static int __xudc_ep0_queue(struct xusb_ep *ep0, struct xusb_req *req) 1006{ 1007 struct xusb_udc *udc = ep0->udc; 1008 u32 length; 1009 u8 *corebuf; 1010 1011 if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) { 1012 dev_dbg(udc->dev, "%s, bogus device state\n", __func__); 1013 return -EINVAL; 1014 } 1015 if (!list_empty(&ep0->queue)) { 1016 dev_dbg(udc->dev, "%s:ep0 busy\n", __func__); 1017 return -EBUSY; 1018 } 1019 1020 req->usb_req.status = -EINPROGRESS; 1021 req->usb_req.actual = 0; 1022 1023 list_add_tail(&req->queue, &ep0->queue); 1024 1025 if (udc->setup.bRequestType & USB_DIR_IN) { 1026 prefetch(req->usb_req.buf); 1027 length = req->usb_req.length; 1028 corebuf = (void __force *) ((ep0->rambase << 2) + 1029 udc->addr); 1030 length = req->usb_req.actual = min_t(u32, length, 1031 EP0_MAX_PACKET); 1032 memcpy(corebuf, req->usb_req.buf, length); 1033 udc->write_fn(udc->addr, XUSB_EP_BUF0COUNT_OFFSET, length); 1034 udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 1); 1035 } else { 1036 if (udc->setup.wLength) { 1037 /* Enable EP0 buffer to receive data */ 1038 udc->write_fn(udc->addr, XUSB_EP_BUF0COUNT_OFFSET, 0); 1039 udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 1); 1040 } else { 1041 xudc_wrstatus(udc); 1042 } 1043 } 1044 1045 return 0; 1046} 1047 1048/** 1049 * xudc_ep0_queue - Adds the request to endpoint 0 queue. 1050 * @_ep: pointer to the usb endpoint 0 structure. 1051 * @_req: pointer to the usb request structure. 1052 * @gfp_flags: Flags related to the request call. 1053 * 1054 * Return: 0 for success and error value on failure 1055 */ 1056static int xudc_ep0_queue(struct usb_ep *_ep, struct usb_request *_req, 1057 gfp_t gfp_flags) 1058{ 1059 struct xusb_req *req = to_xusb_req(_req); 1060 struct xusb_ep *ep0 = to_xusb_ep(_ep); 1061 struct xusb_udc *udc = ep0->udc; 1062 unsigned long flags; 1063 int ret; 1064 1065 spin_lock_irqsave(&udc->lock, flags); 1066 ret = __xudc_ep0_queue(ep0, req); 1067 spin_unlock_irqrestore(&udc->lock, flags); 1068 1069 return ret; 1070} 1071 1072/** 1073 * xudc_ep_queue - Adds the request to endpoint queue. 1074 * @_ep: pointer to the usb endpoint structure. 1075 * @_req: pointer to the usb request structure. 1076 * @gfp_flags: Flags related to the request call. 1077 * 1078 * Return: 0 for success and error value on failure 1079 */ 1080static int xudc_ep_queue(struct usb_ep *_ep, struct usb_request *_req, 1081 gfp_t gfp_flags) 1082{ 1083 struct xusb_req *req = to_xusb_req(_req); 1084 struct xusb_ep *ep = to_xusb_ep(_ep); 1085 struct xusb_udc *udc = ep->udc; 1086 int ret; 1087 unsigned long flags; 1088 1089 if (!ep->desc) { 1090 dev_dbg(udc->dev, "%s:queing request to disabled %s\n", 1091 __func__, ep->name); 1092 return -ESHUTDOWN; 1093 } 1094 1095 if (!udc->driver || udc->gadget.speed == USB_SPEED_UNKNOWN) { 1096 dev_dbg(udc->dev, "%s, bogus device state\n", __func__); 1097 return -EINVAL; 1098 } 1099 1100 spin_lock_irqsave(&udc->lock, flags); 1101 1102 _req->status = -EINPROGRESS; 1103 _req->actual = 0; 1104 1105 if (udc->dma_enabled) { 1106 ret = usb_gadget_map_request(&udc->gadget, &req->usb_req, 1107 ep->is_in); 1108 if (ret) { 1109 dev_dbg(udc->dev, "gadget_map failed ep%d\n", 1110 ep->epnumber); 1111 spin_unlock_irqrestore(&udc->lock, flags); 1112 return -EAGAIN; 1113 } 1114 } 1115 1116 if (list_empty(&ep->queue)) { 1117 if (ep->is_in) { 1118 dev_dbg(udc->dev, "xudc_write_fifo from ep_queue\n"); 1119 if (!xudc_write_fifo(ep, req)) 1120 req = NULL; 1121 } else { 1122 dev_dbg(udc->dev, "xudc_read_fifo from ep_queue\n"); 1123 if (!xudc_read_fifo(ep, req)) 1124 req = NULL; 1125 } 1126 } 1127 1128 if (req != NULL) 1129 list_add_tail(&req->queue, &ep->queue); 1130 1131 spin_unlock_irqrestore(&udc->lock, flags); 1132 return 0; 1133} 1134 1135/** 1136 * xudc_ep_dequeue - Removes the request from the queue. 1137 * @_ep: pointer to the usb device endpoint structure. 1138 * @_req: pointer to the usb request structure. 1139 * 1140 * Return: 0 for success and error value on failure 1141 */ 1142static int xudc_ep_dequeue(struct usb_ep *_ep, struct usb_request *_req) 1143{ 1144 struct xusb_ep *ep = to_xusb_ep(_ep); 1145 struct xusb_req *req = to_xusb_req(_req); 1146 struct xusb_udc *udc = ep->udc; 1147 unsigned long flags; 1148 1149 spin_lock_irqsave(&udc->lock, flags); 1150 /* Make sure it's actually queued on this endpoint */ 1151 list_for_each_entry(req, &ep->queue, queue) { 1152 if (&req->usb_req == _req) 1153 break; 1154 } 1155 if (&req->usb_req != _req) { 1156 spin_unlock_irqrestore(&ep->udc->lock, flags); 1157 return -EINVAL; 1158 } 1159 xudc_done(ep, req, -ECONNRESET); 1160 spin_unlock_irqrestore(&udc->lock, flags); 1161 1162 return 0; 1163} 1164 1165/** 1166 * xudc_ep0_enable - Enables the given endpoint. 1167 * @ep: pointer to the usb endpoint structure. 1168 * @desc: pointer to usb endpoint descriptor. 1169 * 1170 * Return: error always. 1171 * 1172 * endpoint 0 enable should not be called by gadget layer. 1173 */ 1174static int xudc_ep0_enable(struct usb_ep *ep, 1175 const struct usb_endpoint_descriptor *desc) 1176{ 1177 return -EINVAL; 1178} 1179 1180/** 1181 * xudc_ep0_disable - Disables the given endpoint. 1182 * @ep: pointer to the usb endpoint structure. 1183 * 1184 * Return: error always. 1185 * 1186 * endpoint 0 disable should not be called by gadget layer. 1187 */ 1188static int xudc_ep0_disable(struct usb_ep *ep) 1189{ 1190 return -EINVAL; 1191} 1192 1193static const struct usb_ep_ops xusb_ep0_ops = { 1194 .enable = xudc_ep0_enable, 1195 .disable = xudc_ep0_disable, 1196 .alloc_request = xudc_ep_alloc_request, 1197 .free_request = xudc_free_request, 1198 .queue = xudc_ep0_queue, 1199 .dequeue = xudc_ep_dequeue, 1200 .set_halt = xudc_ep_set_halt, 1201}; 1202 1203static const struct usb_ep_ops xusb_ep_ops = { 1204 .enable = xudc_ep_enable, 1205 .disable = xudc_ep_disable, 1206 .alloc_request = xudc_ep_alloc_request, 1207 .free_request = xudc_free_request, 1208 .queue = xudc_ep_queue, 1209 .dequeue = xudc_ep_dequeue, 1210 .set_halt = xudc_ep_set_halt, 1211}; 1212 1213/** 1214 * xudc_get_frame - Reads the current usb frame number. 1215 * @gadget: pointer to the usb gadget structure. 1216 * 1217 * Return: current frame number for success and error value on failure. 1218 */ 1219static int xudc_get_frame(struct usb_gadget *gadget) 1220{ 1221 struct xusb_udc *udc; 1222 int frame; 1223 1224 if (!gadget) 1225 return -ENODEV; 1226 1227 udc = to_udc(gadget); 1228 frame = udc->read_fn(udc->addr + XUSB_FRAMENUM_OFFSET); 1229 return frame; 1230} 1231 1232/** 1233 * xudc_wakeup - Send remote wakeup signal to host 1234 * @gadget: pointer to the usb gadget structure. 1235 * 1236 * Return: 0 on success and error on failure 1237 */ 1238static int xudc_wakeup(struct usb_gadget *gadget) 1239{ 1240 struct xusb_udc *udc = to_udc(gadget); 1241 u32 crtlreg; 1242 int status = -EINVAL; 1243 unsigned long flags; 1244 1245 spin_lock_irqsave(&udc->lock, flags); 1246 1247 /* Remote wake up not enabled by host */ 1248 if (!udc->remote_wkp) 1249 goto done; 1250 1251 crtlreg = udc->read_fn(udc->addr + XUSB_CONTROL_OFFSET); 1252 crtlreg |= XUSB_CONTROL_USB_RMTWAKE_MASK; 1253 /* set remote wake up bit */ 1254 udc->write_fn(udc->addr, XUSB_CONTROL_OFFSET, crtlreg); 1255 /* 1256 * wait for a while and reset remote wake up bit since this bit 1257 * is not cleared by HW after sending remote wakeup to host. 1258 */ 1259 mdelay(2); 1260 1261 crtlreg &= ~XUSB_CONTROL_USB_RMTWAKE_MASK; 1262 udc->write_fn(udc->addr, XUSB_CONTROL_OFFSET, crtlreg); 1263 status = 0; 1264done: 1265 spin_unlock_irqrestore(&udc->lock, flags); 1266 return status; 1267} 1268 1269/** 1270 * xudc_pullup - start/stop USB traffic 1271 * @gadget: pointer to the usb gadget structure. 1272 * @is_on: flag to start or stop 1273 * 1274 * Return: 0 always 1275 * 1276 * This function starts/stops SIE engine of IP based on is_on. 1277 */ 1278static int xudc_pullup(struct usb_gadget *gadget, int is_on) 1279{ 1280 struct xusb_udc *udc = to_udc(gadget); 1281 unsigned long flags; 1282 u32 crtlreg; 1283 1284 spin_lock_irqsave(&udc->lock, flags); 1285 1286 crtlreg = udc->read_fn(udc->addr + XUSB_CONTROL_OFFSET); 1287 if (is_on) 1288 crtlreg |= XUSB_CONTROL_USB_READY_MASK; 1289 else 1290 crtlreg &= ~XUSB_CONTROL_USB_READY_MASK; 1291 1292 udc->write_fn(udc->addr, XUSB_CONTROL_OFFSET, crtlreg); 1293 1294 spin_unlock_irqrestore(&udc->lock, flags); 1295 1296 return 0; 1297} 1298 1299/** 1300 * xudc_eps_init - initialize endpoints. 1301 * @udc: pointer to the usb device controller structure. 1302 */ 1303static void xudc_eps_init(struct xusb_udc *udc) 1304{ 1305 u32 ep_number; 1306 1307 INIT_LIST_HEAD(&udc->gadget.ep_list); 1308 1309 for (ep_number = 0; ep_number < XUSB_MAX_ENDPOINTS; ep_number++) { 1310 struct xusb_ep *ep = &udc->ep[ep_number]; 1311 1312 if (ep_number) { 1313 list_add_tail(&ep->ep_usb.ep_list, 1314 &udc->gadget.ep_list); 1315 usb_ep_set_maxpacket_limit(&ep->ep_usb, 1316 (unsigned short) ~0); 1317 snprintf(ep->name, EPNAME_SIZE, "ep%d", ep_number); 1318 ep->ep_usb.name = ep->name; 1319 ep->ep_usb.ops = &xusb_ep_ops; 1320 } else { 1321 ep->ep_usb.name = ep0name; 1322 usb_ep_set_maxpacket_limit(&ep->ep_usb, EP0_MAX_PACKET); 1323 ep->ep_usb.ops = &xusb_ep0_ops; 1324 } 1325 1326 ep->udc = udc; 1327 ep->epnumber = ep_number; 1328 ep->desc = NULL; 1329 /* 1330 * The configuration register address offset between 1331 * each endpoint is 0x10. 1332 */ 1333 ep->offset = XUSB_EP0_CONFIG_OFFSET + (ep_number * 0x10); 1334 ep->is_in = 0; 1335 ep->is_iso = 0; 1336 ep->maxpacket = 0; 1337 xudc_epconfig(ep, udc); 1338 1339 /* Initialize one queue per endpoint */ 1340 INIT_LIST_HEAD(&ep->queue); 1341 } 1342} 1343 1344/** 1345 * xudc_stop_activity - Stops any further activity on the device. 1346 * @udc: pointer to the usb device controller structure. 1347 */ 1348static void xudc_stop_activity(struct xusb_udc *udc) 1349{ 1350 int i; 1351 struct xusb_ep *ep; 1352 1353 for (i = 0; i < XUSB_MAX_ENDPOINTS; i++) { 1354 ep = &udc->ep[i]; 1355 xudc_nuke(ep, -ESHUTDOWN); 1356 } 1357} 1358 1359/** 1360 * xudc_start - Starts the device. 1361 * @gadget: pointer to the usb gadget structure 1362 * @driver: pointer to gadget driver structure 1363 * 1364 * Return: zero on success and error on failure 1365 */ 1366static int xudc_start(struct usb_gadget *gadget, 1367 struct usb_gadget_driver *driver) 1368{ 1369 struct xusb_udc *udc = to_udc(gadget); 1370 struct xusb_ep *ep0 = &udc->ep[XUSB_EP_NUMBER_ZERO]; 1371 const struct usb_endpoint_descriptor *desc = &config_bulk_out_desc; 1372 unsigned long flags; 1373 int ret = 0; 1374 1375 spin_lock_irqsave(&udc->lock, flags); 1376 1377 if (udc->driver) { 1378 dev_err(udc->dev, "%s is already bound to %s\n", 1379 udc->gadget.name, udc->driver->driver.name); 1380 ret = -EBUSY; 1381 goto err; 1382 } 1383 1384 /* hook up the driver */ 1385 udc->driver = driver; 1386 udc->gadget.speed = driver->max_speed; 1387 1388 /* Enable the control endpoint. */ 1389 ret = __xudc_ep_enable(ep0, desc); 1390 1391 /* Set device address and remote wakeup to 0 */ 1392 udc->write_fn(udc->addr, XUSB_ADDRESS_OFFSET, 0); 1393 udc->remote_wkp = 0; 1394err: 1395 spin_unlock_irqrestore(&udc->lock, flags); 1396 return ret; 1397} 1398 1399/** 1400 * xudc_stop - stops the device. 1401 * @gadget: pointer to the usb gadget structure 1402 * @driver: pointer to usb gadget driver structure 1403 * 1404 * Return: zero always 1405 */ 1406static int xudc_stop(struct usb_gadget *gadget) 1407{ 1408 struct xusb_udc *udc = to_udc(gadget); 1409 unsigned long flags; 1410 1411 spin_lock_irqsave(&udc->lock, flags); 1412 1413 udc->gadget.speed = USB_SPEED_UNKNOWN; 1414 udc->driver = NULL; 1415 1416 /* Set device address and remote wakeup to 0 */ 1417 udc->write_fn(udc->addr, XUSB_ADDRESS_OFFSET, 0); 1418 udc->remote_wkp = 0; 1419 1420 xudc_stop_activity(udc); 1421 1422 spin_unlock_irqrestore(&udc->lock, flags); 1423 1424 return 0; 1425} 1426 1427static const struct usb_gadget_ops xusb_udc_ops = { 1428 .get_frame = xudc_get_frame, 1429 .wakeup = xudc_wakeup, 1430 .pullup = xudc_pullup, 1431 .udc_start = xudc_start, 1432 .udc_stop = xudc_stop, 1433}; 1434 1435/** 1436 * xudc_clear_stall_all_ep - clears stall of every endpoint. 1437 * @udc: pointer to the udc structure. 1438 */ 1439static void xudc_clear_stall_all_ep(struct xusb_udc *udc) 1440{ 1441 struct xusb_ep *ep; 1442 u32 epcfgreg; 1443 int i; 1444 1445 for (i = 0; i < XUSB_MAX_ENDPOINTS; i++) { 1446 ep = &udc->ep[i]; 1447 epcfgreg = udc->read_fn(udc->addr + ep->offset); 1448 epcfgreg &= ~XUSB_EP_CFG_STALL_MASK; 1449 udc->write_fn(udc->addr, ep->offset, epcfgreg); 1450 if (ep->epnumber) { 1451 /* Reset the toggle bit.*/ 1452 epcfgreg = udc->read_fn(udc->addr + ep->offset); 1453 epcfgreg &= ~XUSB_EP_CFG_DATA_TOGGLE_MASK; 1454 udc->write_fn(udc->addr, ep->offset, epcfgreg); 1455 } 1456 } 1457} 1458 1459/** 1460 * xudc_startup_handler - The usb device controller interrupt handler. 1461 * @udc: pointer to the udc structure. 1462 * @intrstatus: The mask value containing the interrupt sources. 1463 * 1464 * This function handles the RESET,SUSPEND,RESUME and DISCONNECT interrupts. 1465 */ 1466static void xudc_startup_handler(struct xusb_udc *udc, u32 intrstatus) 1467{ 1468 u32 intrreg; 1469 1470 if (intrstatus & XUSB_STATUS_RESET_MASK) { 1471 1472 dev_dbg(udc->dev, "Reset\n"); 1473 1474 if (intrstatus & XUSB_STATUS_HIGH_SPEED_MASK) 1475 udc->gadget.speed = USB_SPEED_HIGH; 1476 else 1477 udc->gadget.speed = USB_SPEED_FULL; 1478 1479 xudc_stop_activity(udc); 1480 xudc_clear_stall_all_ep(udc); 1481 udc->write_fn(udc->addr, XUSB_TESTMODE_OFFSET, 0); 1482 1483 /* Set device address and remote wakeup to 0 */ 1484 udc->write_fn(udc->addr, XUSB_ADDRESS_OFFSET, 0); 1485 udc->remote_wkp = 0; 1486 1487 /* Enable the suspend, resume and disconnect */ 1488 intrreg = udc->read_fn(udc->addr + XUSB_IER_OFFSET); 1489 intrreg |= XUSB_STATUS_SUSPEND_MASK | XUSB_STATUS_RESUME_MASK | 1490 XUSB_STATUS_DISCONNECT_MASK; 1491 udc->write_fn(udc->addr, XUSB_IER_OFFSET, intrreg); 1492 } 1493 if (intrstatus & XUSB_STATUS_SUSPEND_MASK) { 1494 1495 dev_dbg(udc->dev, "Suspend\n"); 1496 1497 /* Enable the reset, resume and disconnect */ 1498 intrreg = udc->read_fn(udc->addr + XUSB_IER_OFFSET); 1499 intrreg |= XUSB_STATUS_RESET_MASK | XUSB_STATUS_RESUME_MASK | 1500 XUSB_STATUS_DISCONNECT_MASK; 1501 udc->write_fn(udc->addr, XUSB_IER_OFFSET, intrreg); 1502 1503 udc->usb_state = USB_STATE_SUSPENDED; 1504 1505 if (udc->driver->suspend) { 1506 spin_unlock(&udc->lock); 1507 udc->driver->suspend(&udc->gadget); 1508 spin_lock(&udc->lock); 1509 } 1510 } 1511 if (intrstatus & XUSB_STATUS_RESUME_MASK) { 1512 bool condition = (udc->usb_state != USB_STATE_SUSPENDED); 1513 1514 dev_WARN_ONCE(udc->dev, condition, 1515 "Resume IRQ while not suspended\n"); 1516 1517 dev_dbg(udc->dev, "Resume\n"); 1518 1519 /* Enable the reset, suspend and disconnect */ 1520 intrreg = udc->read_fn(udc->addr + XUSB_IER_OFFSET); 1521 intrreg |= XUSB_STATUS_RESET_MASK | XUSB_STATUS_SUSPEND_MASK | 1522 XUSB_STATUS_DISCONNECT_MASK; 1523 udc->write_fn(udc->addr, XUSB_IER_OFFSET, intrreg); 1524 1525 udc->usb_state = 0; 1526 1527 if (udc->driver->resume) { 1528 spin_unlock(&udc->lock); 1529 udc->driver->resume(&udc->gadget); 1530 spin_lock(&udc->lock); 1531 } 1532 } 1533 if (intrstatus & XUSB_STATUS_DISCONNECT_MASK) { 1534 1535 dev_dbg(udc->dev, "Disconnect\n"); 1536 1537 /* Enable the reset, resume and suspend */ 1538 intrreg = udc->read_fn(udc->addr + XUSB_IER_OFFSET); 1539 intrreg |= XUSB_STATUS_RESET_MASK | XUSB_STATUS_RESUME_MASK | 1540 XUSB_STATUS_SUSPEND_MASK; 1541 udc->write_fn(udc->addr, XUSB_IER_OFFSET, intrreg); 1542 1543 if (udc->driver && udc->driver->disconnect) { 1544 spin_unlock(&udc->lock); 1545 udc->driver->disconnect(&udc->gadget); 1546 spin_lock(&udc->lock); 1547 } 1548 } 1549} 1550 1551/** 1552 * xudc_ep0_stall - Stall endpoint zero. 1553 * @udc: pointer to the udc structure. 1554 * 1555 * This function stalls endpoint zero. 1556 */ 1557static void xudc_ep0_stall(struct xusb_udc *udc) 1558{ 1559 u32 epcfgreg; 1560 struct xusb_ep *ep0 = &udc->ep[XUSB_EP_NUMBER_ZERO]; 1561 1562 epcfgreg = udc->read_fn(udc->addr + ep0->offset); 1563 epcfgreg |= XUSB_EP_CFG_STALL_MASK; 1564 udc->write_fn(udc->addr, ep0->offset, epcfgreg); 1565} 1566 1567/** 1568 * xudc_setaddress - executes SET_ADDRESS command 1569 * @udc: pointer to the udc structure. 1570 * 1571 * This function executes USB SET_ADDRESS command 1572 */ 1573static void xudc_setaddress(struct xusb_udc *udc) 1574{ 1575 struct xusb_ep *ep0 = &udc->ep[0]; 1576 struct xusb_req *req = udc->req; 1577 int ret; 1578 1579 req->usb_req.length = 0; 1580 ret = __xudc_ep0_queue(ep0, req); 1581 if (ret == 0) 1582 return; 1583 1584 dev_err(udc->dev, "Can't respond to SET ADDRESS request\n"); 1585 xudc_ep0_stall(udc); 1586} 1587 1588/** 1589 * xudc_getstatus - executes GET_STATUS command 1590 * @udc: pointer to the udc structure. 1591 * 1592 * This function executes USB GET_STATUS command 1593 */ 1594static void xudc_getstatus(struct xusb_udc *udc) 1595{ 1596 struct xusb_ep *ep0 = &udc->ep[0]; 1597 struct xusb_req *req = udc->req; 1598 struct xusb_ep *target_ep; 1599 u16 status = 0; 1600 u32 epcfgreg; 1601 int epnum; 1602 u32 halt; 1603 int ret; 1604 1605 switch (udc->setup.bRequestType & USB_RECIP_MASK) { 1606 case USB_RECIP_DEVICE: 1607 /* Get device status */ 1608 status = 1 << USB_DEVICE_SELF_POWERED; 1609 if (udc->remote_wkp) 1610 status |= (1 << USB_DEVICE_REMOTE_WAKEUP); 1611 break; 1612 case USB_RECIP_INTERFACE: 1613 break; 1614 case USB_RECIP_ENDPOINT: 1615 epnum = udc->setup.wIndex & USB_ENDPOINT_NUMBER_MASK; 1616 target_ep = &udc->ep[epnum]; 1617 epcfgreg = udc->read_fn(udc->addr + target_ep->offset); 1618 halt = epcfgreg & XUSB_EP_CFG_STALL_MASK; 1619 if (udc->setup.wIndex & USB_DIR_IN) { 1620 if (!target_ep->is_in) 1621 goto stall; 1622 } else { 1623 if (target_ep->is_in) 1624 goto stall; 1625 } 1626 if (halt) 1627 status = 1 << USB_ENDPOINT_HALT; 1628 break; 1629 default: 1630 goto stall; 1631 } 1632 1633 req->usb_req.length = 2; 1634 *(u16 *)req->usb_req.buf = cpu_to_le16(status); 1635 ret = __xudc_ep0_queue(ep0, req); 1636 if (ret == 0) 1637 return; 1638stall: 1639 dev_err(udc->dev, "Can't respond to getstatus request\n"); 1640 xudc_ep0_stall(udc); 1641} 1642 1643/** 1644 * xudc_set_clear_feature - Executes the set feature and clear feature commands. 1645 * @udc: pointer to the usb device controller structure. 1646 * 1647 * Processes the SET_FEATURE and CLEAR_FEATURE commands. 1648 */ 1649static void xudc_set_clear_feature(struct xusb_udc *udc) 1650{ 1651 struct xusb_ep *ep0 = &udc->ep[0]; 1652 struct xusb_req *req = udc->req; 1653 struct xusb_ep *target_ep; 1654 u8 endpoint; 1655 u8 outinbit; 1656 u32 epcfgreg; 1657 int flag = (udc->setup.bRequest == USB_REQ_SET_FEATURE ? 1 : 0); 1658 int ret; 1659 1660 switch (udc->setup.bRequestType) { 1661 case USB_RECIP_DEVICE: 1662 switch (udc->setup.wValue) { 1663 case USB_DEVICE_TEST_MODE: 1664 /* 1665 * The Test Mode will be executed 1666 * after the status phase. 1667 */ 1668 break; 1669 case USB_DEVICE_REMOTE_WAKEUP: 1670 if (flag) 1671 udc->remote_wkp = 1; 1672 else 1673 udc->remote_wkp = 0; 1674 break; 1675 default: 1676 xudc_ep0_stall(udc); 1677 break; 1678 } 1679 break; 1680 case USB_RECIP_ENDPOINT: 1681 if (!udc->setup.wValue) { 1682 endpoint = udc->setup.wIndex & USB_ENDPOINT_NUMBER_MASK; 1683 target_ep = &udc->ep[endpoint]; 1684 outinbit = udc->setup.wIndex & USB_ENDPOINT_DIR_MASK; 1685 outinbit = outinbit >> 7; 1686 1687 /* Make sure direction matches.*/ 1688 if (outinbit != target_ep->is_in) { 1689 xudc_ep0_stall(udc); 1690 return; 1691 } 1692 epcfgreg = udc->read_fn(udc->addr + target_ep->offset); 1693 if (!endpoint) { 1694 /* Clear the stall.*/ 1695 epcfgreg &= ~XUSB_EP_CFG_STALL_MASK; 1696 udc->write_fn(udc->addr, 1697 target_ep->offset, epcfgreg); 1698 } else { 1699 if (flag) { 1700 epcfgreg |= XUSB_EP_CFG_STALL_MASK; 1701 udc->write_fn(udc->addr, 1702 target_ep->offset, 1703 epcfgreg); 1704 } else { 1705 /* Unstall the endpoint.*/ 1706 epcfgreg &= ~(XUSB_EP_CFG_STALL_MASK | 1707 XUSB_EP_CFG_DATA_TOGGLE_MASK); 1708 udc->write_fn(udc->addr, 1709 target_ep->offset, 1710 epcfgreg); 1711 } 1712 } 1713 } 1714 break; 1715 default: 1716 xudc_ep0_stall(udc); 1717 return; 1718 } 1719 1720 req->usb_req.length = 0; 1721 ret = __xudc_ep0_queue(ep0, req); 1722 if (ret == 0) 1723 return; 1724 1725 dev_err(udc->dev, "Can't respond to SET/CLEAR FEATURE\n"); 1726 xudc_ep0_stall(udc); 1727} 1728 1729/** 1730 * xudc_handle_setup - Processes the setup packet. 1731 * @udc: pointer to the usb device controller structure. 1732 * 1733 * Process setup packet and delegate to gadget layer. 1734 */ 1735static void xudc_handle_setup(struct xusb_udc *udc) 1736{ 1737 struct xusb_ep *ep0 = &udc->ep[0]; 1738 struct usb_ctrlrequest setup; 1739 u32 *ep0rambase; 1740 1741 /* Load up the chapter 9 command buffer.*/ 1742 ep0rambase = (u32 __force *) (udc->addr + XUSB_SETUP_PKT_ADDR_OFFSET); 1743 memcpy(&setup, ep0rambase, 8); 1744 1745 udc->setup = setup; 1746 udc->setup.wValue = cpu_to_le16(setup.wValue); 1747 udc->setup.wIndex = cpu_to_le16(setup.wIndex); 1748 udc->setup.wLength = cpu_to_le16(setup.wLength); 1749 1750 /* Clear previous requests */ 1751 xudc_nuke(ep0, -ECONNRESET); 1752 1753 if (udc->setup.bRequestType & USB_DIR_IN) { 1754 /* Execute the get command.*/ 1755 udc->setupseqrx = STATUS_PHASE; 1756 udc->setupseqtx = DATA_PHASE; 1757 } else { 1758 /* Execute the put command.*/ 1759 udc->setupseqrx = DATA_PHASE; 1760 udc->setupseqtx = STATUS_PHASE; 1761 } 1762 1763 switch (udc->setup.bRequest) { 1764 case USB_REQ_GET_STATUS: 1765 /* Data+Status phase form udc */ 1766 if ((udc->setup.bRequestType & 1767 (USB_DIR_IN | USB_TYPE_MASK)) != 1768 (USB_DIR_IN | USB_TYPE_STANDARD)) 1769 break; 1770 xudc_getstatus(udc); 1771 return; 1772 case USB_REQ_SET_ADDRESS: 1773 /* Status phase from udc */ 1774 if (udc->setup.bRequestType != (USB_DIR_OUT | 1775 USB_TYPE_STANDARD | USB_RECIP_DEVICE)) 1776 break; 1777 xudc_setaddress(udc); 1778 return; 1779 case USB_REQ_CLEAR_FEATURE: 1780 case USB_REQ_SET_FEATURE: 1781 /* Requests with no data phase, status phase from udc */ 1782 if ((udc->setup.bRequestType & USB_TYPE_MASK) 1783 != USB_TYPE_STANDARD) 1784 break; 1785 xudc_set_clear_feature(udc); 1786 return; 1787 default: 1788 break; 1789 } 1790 1791 spin_unlock(&udc->lock); 1792 if (udc->driver->setup(&udc->gadget, &setup) < 0) 1793 xudc_ep0_stall(udc); 1794 spin_lock(&udc->lock); 1795} 1796 1797/** 1798 * xudc_ep0_out - Processes the endpoint 0 OUT token. 1799 * @udc: pointer to the usb device controller structure. 1800 */ 1801static void xudc_ep0_out(struct xusb_udc *udc) 1802{ 1803 struct xusb_ep *ep0 = &udc->ep[0]; 1804 struct xusb_req *req; 1805 u8 *ep0rambase; 1806 unsigned int bytes_to_rx; 1807 void *buffer; 1808 1809 req = list_first_entry(&ep0->queue, struct xusb_req, queue); 1810 1811 switch (udc->setupseqrx) { 1812 case STATUS_PHASE: 1813 /* 1814 * This resets both state machines for the next 1815 * Setup packet. 1816 */ 1817 udc->setupseqrx = SETUP_PHASE; 1818 udc->setupseqtx = SETUP_PHASE; 1819 req->usb_req.actual = req->usb_req.length; 1820 xudc_done(ep0, req, 0); 1821 break; 1822 case DATA_PHASE: 1823 bytes_to_rx = udc->read_fn(udc->addr + 1824 XUSB_EP_BUF0COUNT_OFFSET); 1825 /* Copy the data to be received from the DPRAM. */ 1826 ep0rambase = (u8 __force *) (udc->addr + 1827 (ep0->rambase << 2)); 1828 buffer = req->usb_req.buf + req->usb_req.actual; 1829 req->usb_req.actual = req->usb_req.actual + bytes_to_rx; 1830 memcpy(buffer, ep0rambase, bytes_to_rx); 1831 1832 if (req->usb_req.length == req->usb_req.actual) { 1833 /* Data transfer completed get ready for Status stage */ 1834 xudc_wrstatus(udc); 1835 } else { 1836 /* Enable EP0 buffer to receive data */ 1837 udc->write_fn(udc->addr, XUSB_EP_BUF0COUNT_OFFSET, 0); 1838 udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 1); 1839 } 1840 break; 1841 default: 1842 break; 1843 } 1844} 1845 1846/** 1847 * xudc_ep0_in - Processes the endpoint 0 IN token. 1848 * @udc: pointer to the usb device controller structure. 1849 */ 1850static void xudc_ep0_in(struct xusb_udc *udc) 1851{ 1852 struct xusb_ep *ep0 = &udc->ep[0]; 1853 struct xusb_req *req; 1854 unsigned int bytes_to_tx; 1855 void *buffer; 1856 u32 epcfgreg; 1857 u16 count = 0; 1858 u16 length; 1859 u8 *ep0rambase; 1860 u8 test_mode = udc->setup.wIndex >> 8; 1861 1862 req = list_first_entry(&ep0->queue, struct xusb_req, queue); 1863 bytes_to_tx = req->usb_req.length - req->usb_req.actual; 1864 1865 switch (udc->setupseqtx) { 1866 case STATUS_PHASE: 1867 switch (udc->setup.bRequest) { 1868 case USB_REQ_SET_ADDRESS: 1869 /* Set the address of the device.*/ 1870 udc->write_fn(udc->addr, XUSB_ADDRESS_OFFSET, 1871 udc->setup.wValue); 1872 break; 1873 case USB_REQ_SET_FEATURE: 1874 if (udc->setup.bRequestType == 1875 USB_RECIP_DEVICE) { 1876 if (udc->setup.wValue == 1877 USB_DEVICE_TEST_MODE) 1878 udc->write_fn(udc->addr, 1879 XUSB_TESTMODE_OFFSET, 1880 test_mode); 1881 } 1882 break; 1883 } 1884 req->usb_req.actual = req->usb_req.length; 1885 xudc_done(ep0, req, 0); 1886 break; 1887 case DATA_PHASE: 1888 if (!bytes_to_tx) { 1889 /* 1890 * We're done with data transfer, next 1891 * will be zero length OUT with data toggle of 1892 * 1. Setup data_toggle. 1893 */ 1894 epcfgreg = udc->read_fn(udc->addr + ep0->offset); 1895 epcfgreg |= XUSB_EP_CFG_DATA_TOGGLE_MASK; 1896 udc->write_fn(udc->addr, ep0->offset, epcfgreg); 1897 udc->setupseqtx = STATUS_PHASE; 1898 } else { 1899 length = count = min_t(u32, bytes_to_tx, 1900 EP0_MAX_PACKET); 1901 /* Copy the data to be transmitted into the DPRAM. */ 1902 ep0rambase = (u8 __force *) (udc->addr + 1903 (ep0->rambase << 2)); 1904 buffer = req->usb_req.buf + req->usb_req.actual; 1905 req->usb_req.actual = req->usb_req.actual + length; 1906 memcpy(ep0rambase, buffer, length); 1907 } 1908 udc->write_fn(udc->addr, XUSB_EP_BUF0COUNT_OFFSET, count); 1909 udc->write_fn(udc->addr, XUSB_BUFFREADY_OFFSET, 1); 1910 break; 1911 default: 1912 break; 1913 } 1914} 1915 1916/** 1917 * xudc_ctrl_ep_handler - Endpoint 0 interrupt handler. 1918 * @udc: pointer to the udc structure. 1919 * @intrstatus: It's the mask value for the interrupt sources on endpoint 0. 1920 * 1921 * Processes the commands received during enumeration phase. 1922 */ 1923static void xudc_ctrl_ep_handler(struct xusb_udc *udc, u32 intrstatus) 1924{ 1925 1926 if (intrstatus & XUSB_STATUS_SETUP_PACKET_MASK) { 1927 xudc_handle_setup(udc); 1928 } else { 1929 if (intrstatus & XUSB_STATUS_FIFO_BUFF_RDY_MASK) 1930 xudc_ep0_out(udc); 1931 else if (intrstatus & XUSB_STATUS_FIFO_BUFF_FREE_MASK) 1932 xudc_ep0_in(udc); 1933 } 1934} 1935 1936/** 1937 * xudc_nonctrl_ep_handler - Non control endpoint interrupt handler. 1938 * @udc: pointer to the udc structure. 1939 * @epnum: End point number for which the interrupt is to be processed 1940 * @intrstatus: mask value for interrupt sources of endpoints other 1941 * than endpoint 0. 1942 * 1943 * Processes the buffer completion interrupts. 1944 */ 1945static void xudc_nonctrl_ep_handler(struct xusb_udc *udc, u8 epnum, 1946 u32 intrstatus) 1947{ 1948 1949 struct xusb_req *req; 1950 struct xusb_ep *ep; 1951 1952 ep = &udc->ep[epnum]; 1953 /* Process the End point interrupts.*/ 1954 if (intrstatus & (XUSB_STATUS_EP0_BUFF1_COMP_MASK << epnum)) 1955 ep->buffer0ready = 0; 1956 if (intrstatus & (XUSB_STATUS_EP0_BUFF2_COMP_MASK << epnum)) 1957 ep->buffer1ready = 0; 1958 1959 if (list_empty(&ep->queue)) 1960 return; 1961 1962 req = list_first_entry(&ep->queue, struct xusb_req, queue); 1963 1964 if (ep->is_in) 1965 xudc_write_fifo(ep, req); 1966 else 1967 xudc_read_fifo(ep, req); 1968} 1969 1970/** 1971 * xudc_irq - The main interrupt handler. 1972 * @irq: The interrupt number. 1973 * @_udc: pointer to the usb device controller structure. 1974 * 1975 * Return: IRQ_HANDLED after the interrupt is handled. 1976 */ 1977static irqreturn_t xudc_irq(int irq, void *_udc) 1978{ 1979 struct xusb_udc *udc = _udc; 1980 u32 intrstatus; 1981 u32 ier; 1982 u8 index; 1983 u32 bufintr; 1984 unsigned long flags; 1985 1986 spin_lock_irqsave(&udc->lock, flags); 1987 1988 /* 1989 * Event interrupts are level sensitive hence first disable 1990 * IER, read ISR and figure out active interrupts. 1991 */ 1992 ier = udc->read_fn(udc->addr + XUSB_IER_OFFSET); 1993 ier &= ~XUSB_STATUS_INTR_EVENT_MASK; 1994 udc->write_fn(udc->addr, XUSB_IER_OFFSET, ier); 1995 1996 /* Read the Interrupt Status Register.*/ 1997 intrstatus = udc->read_fn(udc->addr + XUSB_STATUS_OFFSET); 1998 1999 /* Call the handler for the event interrupt.*/ 2000 if (intrstatus & XUSB_STATUS_INTR_EVENT_MASK) { 2001 /* 2002 * Check if there is any action to be done for : 2003 * - USB Reset received {XUSB_STATUS_RESET_MASK} 2004 * - USB Suspend received {XUSB_STATUS_SUSPEND_MASK} 2005 * - USB Resume received {XUSB_STATUS_RESUME_MASK} 2006 * - USB Disconnect received {XUSB_STATUS_DISCONNECT_MASK} 2007 */ 2008 xudc_startup_handler(udc, intrstatus); 2009 } 2010 2011 /* Check the buffer completion interrupts */ 2012 if (intrstatus & XUSB_STATUS_INTR_BUFF_COMP_ALL_MASK) { 2013 /* Enable Reset, Suspend, Resume and Disconnect */ 2014 ier = udc->read_fn(udc->addr + XUSB_IER_OFFSET); 2015 ier |= XUSB_STATUS_INTR_EVENT_MASK; 2016 udc->write_fn(udc->addr, XUSB_IER_OFFSET, ier); 2017 2018 if (intrstatus & XUSB_STATUS_EP0_BUFF1_COMP_MASK) 2019 xudc_ctrl_ep_handler(udc, intrstatus); 2020 2021 for (index = 1; index < 8; index++) { 2022 bufintr = ((intrstatus & 2023 (XUSB_STATUS_EP1_BUFF1_COMP_MASK << 2024 (index - 1))) || (intrstatus & 2025 (XUSB_STATUS_EP1_BUFF2_COMP_MASK << 2026 (index - 1)))); 2027 if (bufintr) { 2028 xudc_nonctrl_ep_handler(udc, index, 2029 intrstatus); 2030 } 2031 } 2032 } 2033 2034 spin_unlock_irqrestore(&udc->lock, flags); 2035 return IRQ_HANDLED; 2036} 2037 2038/** 2039 * xudc_probe - The device probe function for driver initialization. 2040 * @pdev: pointer to the platform device structure. 2041 * 2042 * Return: 0 for success and error value on failure 2043 */ 2044static int xudc_probe(struct platform_device *pdev) 2045{ 2046 struct device_node *np = pdev->dev.of_node; 2047 struct resource *res; 2048 struct xusb_udc *udc; 2049 struct xusb_ep *ep0; 2050 int irq; 2051 int ret; 2052 u32 ier; 2053 u8 *buff; 2054 2055 udc = devm_kzalloc(&pdev->dev, sizeof(*udc), GFP_KERNEL); 2056 if (!udc) 2057 return -ENOMEM; 2058 2059 /* Create a dummy request for GET_STATUS, SET_ADDRESS */ 2060 udc->req = devm_kzalloc(&pdev->dev, sizeof(struct xusb_req), 2061 GFP_KERNEL); 2062 if (!udc->req) 2063 return -ENOMEM; 2064 2065 buff = devm_kzalloc(&pdev->dev, STATUSBUFF_SIZE, GFP_KERNEL); 2066 if (!buff) 2067 return -ENOMEM; 2068 2069 udc->req->usb_req.buf = buff; 2070 2071 /* Map the registers */ 2072 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 2073 udc->addr = devm_ioremap_resource(&pdev->dev, res); 2074 if (IS_ERR(udc->addr)) 2075 return PTR_ERR(udc->addr); 2076 2077 irq = platform_get_irq(pdev, 0); 2078 if (irq < 0) { 2079 dev_err(&pdev->dev, "unable to get irq\n"); 2080 return irq; 2081 } 2082 ret = devm_request_irq(&pdev->dev, irq, xudc_irq, 0, 2083 dev_name(&pdev->dev), udc); 2084 if (ret < 0) { 2085 dev_dbg(&pdev->dev, "unable to request irq %d", irq); 2086 goto fail; 2087 } 2088 2089 udc->dma_enabled = of_property_read_bool(np, "xlnx,has-builtin-dma"); 2090 2091 /* Setup gadget structure */ 2092 udc->gadget.ops = &xusb_udc_ops; 2093 udc->gadget.max_speed = USB_SPEED_HIGH; 2094 udc->gadget.speed = USB_SPEED_UNKNOWN; 2095 udc->gadget.ep0 = &udc->ep[XUSB_EP_NUMBER_ZERO].ep_usb; 2096 udc->gadget.name = driver_name; 2097 2098 spin_lock_init(&udc->lock); 2099 2100 /* Check for IP endianness */ 2101 udc->write_fn = xudc_write32_be; 2102 udc->read_fn = xudc_read32_be; 2103 udc->write_fn(udc->addr, XUSB_TESTMODE_OFFSET, TEST_J); 2104 if ((udc->read_fn(udc->addr + XUSB_TESTMODE_OFFSET)) 2105 != TEST_J) { 2106 udc->write_fn = xudc_write32; 2107 udc->read_fn = xudc_read32; 2108 } 2109 udc->write_fn(udc->addr, XUSB_TESTMODE_OFFSET, 0); 2110 2111 xudc_eps_init(udc); 2112 2113 ep0 = &udc->ep[0]; 2114 2115 /* Set device address to 0.*/ 2116 udc->write_fn(udc->addr, XUSB_ADDRESS_OFFSET, 0); 2117 2118 ret = usb_add_gadget_udc(&pdev->dev, &udc->gadget); 2119 if (ret) 2120 goto fail; 2121 2122 udc->dev = &udc->gadget.dev; 2123 2124 /* Enable the interrupts.*/ 2125 ier = XUSB_STATUS_GLOBAL_INTR_MASK | XUSB_STATUS_INTR_EVENT_MASK | 2126 XUSB_STATUS_FIFO_BUFF_RDY_MASK | XUSB_STATUS_FIFO_BUFF_FREE_MASK | 2127 XUSB_STATUS_SETUP_PACKET_MASK | 2128 XUSB_STATUS_INTR_BUFF_COMP_ALL_MASK; 2129 2130 udc->write_fn(udc->addr, XUSB_IER_OFFSET, ier); 2131 2132 platform_set_drvdata(pdev, udc); 2133 2134 dev_vdbg(&pdev->dev, "%s at 0x%08X mapped to %p %s\n", 2135 driver_name, (u32)res->start, udc->addr, 2136 udc->dma_enabled ? "with DMA" : "without DMA"); 2137 2138 return 0; 2139fail: 2140 dev_err(&pdev->dev, "probe failed, %d\n", ret); 2141 return ret; 2142} 2143 2144/** 2145 * xudc_remove - Releases the resources allocated during the initialization. 2146 * @pdev: pointer to the platform device structure. 2147 * 2148 * Return: 0 always 2149 */ 2150static int xudc_remove(struct platform_device *pdev) 2151{ 2152 struct xusb_udc *udc = platform_get_drvdata(pdev); 2153 2154 usb_del_gadget_udc(&udc->gadget); 2155 2156 return 0; 2157} 2158 2159/* Match table for of_platform binding */ 2160static const struct of_device_id usb_of_match[] = { 2161 { .compatible = "xlnx,usb2-device-4.00.a", }, 2162 { /* end of list */ }, 2163}; 2164MODULE_DEVICE_TABLE(of, usb_of_match); 2165 2166static struct platform_driver xudc_driver = { 2167 .driver = { 2168 .name = driver_name, 2169 .of_match_table = usb_of_match, 2170 }, 2171 .probe = xudc_probe, 2172 .remove = xudc_remove, 2173}; 2174 2175module_platform_driver(xudc_driver); 2176 2177MODULE_DESCRIPTION("Xilinx udc driver"); 2178MODULE_AUTHOR("Xilinx, Inc"); 2179MODULE_LICENSE("GPL"); 2180